Advertisement
Quick Links
SPECIFICATIONS
Dimensions:
Weight:
Frequency Bands:
Signal Meter
Frequency Response:
The Wall Mount Power Injector is a convenient way to
switch between your cable feed and over-the-air signals
from your JACK antenna.
To use the Power Injector, simply turn the unit on with the
ON/OFF button. When on (button depressed), the power
light will turn green indicating +12 volts to the antenna,
and the over-the-air signal from your JACK antenna will
be fed to the two TV outputs.
When off, the cable TV signal will be fed to the two TV
outputs if wired for cable TV input.
1. Turn on antenna power at Power Injector Wall Mount Plate.
2. Turn on SureLock Signal Meter with switch on side of rotational knob enclosure.
3. Rotate attenuator dial fully clockwise.
NOTE: In step 4, LED lights will illuminate from left (next to power) to right.
All LED lights may not illuminate depending on signal strength.
4. Depress button on rotational knob and rotate antenna
until maximum number of LED lights illuminate on signal meter.
5. Rotate attenuator dial counter clockwise until last illuminated LED light flickers.
6. Rotate antenna to illuminate last flickering LED light.
7. Repeat steps 5 and 6 to pinpoint signal reception.
8. Follow instructions for TV or converter box to scan for available channels.
JACK
®
w/built-in SureLock
11.25" H x 16" W x 12.5" L
2.3 lbs.
VHF (47-230 Mhz) - 20 db gain
UHF (470-860 Mhz) - 25 db gain
40-862 Mhz (Ch 2-69)
POSITIONING THE ANTENNA
Digital HDTV Over-the-Air Antenna
®
OA8200 - White • OA8201 - Black
Powered Amplifier:
Power Supply:
Enclosure/Mount:
OPERATION
Page 1
Digital TV Signal Meter
+12 Volt / 100 mA working
Wall Mt. Switch (included)
• Mfr. # PB1000 - power supply, white
ASA-Automotive grade
NOTE: Arrow on knob indicates which
direction antenna is pointing.
Advertisement
Related Manuals for Jack OA8200
Summary of Contents for Jack OA8200
- Page 1 ON/OFF button. When on (button depressed), the power light will turn green indicating +12 volts to the antenna, and the over-the-air signal from your JACK antenna will be fed to the two TV outputs. When off, the cable TV signal will be fed to the two TV outputs if wired for cable TV input.
- Page 2 For roof thicknesses 1 1/4” to 3 1/2” use the assembly as shipped. For roof thicknesses 3 1/2” to 6” use the longer connector. IMPORTANT! You must install the included wall mount switch KC# PB1000 to operate the JACK antenna. (See page 5) Page 2...
- Page 3 EXTERIOR BASE MOUNT INSTALLATION (FIG. 2) IMPORTANT! The installer is responsible for determining the most appropriate fasteners to secure the base mount to the roof and weatherproofing all holes with sealant. The installer is responsible for sealing all existing holes when replacing an existing antenna mount.
- Page 4 INTERIOR ENCLOSURE INSTALLATION (FIG. 3) IMPORTANT! The rotation knob only fits on the end of the adjustable connector in one direction. SEE INSET BELOW. 1. Press knob button and remove knob from enclosure base. 2. Make sure the coax exits the roof thru the enlarged portion of the roof hole and route the coax thru the coax hole in the enclosure base.
- Page 5 WALL MOUNT POWER INJECTOR INSTALLATION (FIG. 4) 1. Make all connections as shown. The Wall Mount Power Injector: • Can be mounted in most standard electrical boxes. • Requires a +12 Volt DC power source. (Inadequate voltage may cause the green LED to not illuminate and the unit to not function properly.
- Page 6 IMPORTANT! Do not power wash any part of the JACK antenna head or base mount. LIMITED WARRANTY Every new JACK HDTV Antenna System is thoroughly inspected and tested before leaving the factory, and is covered by the following two year parts and one year labor limited warranty from the date of original purchase: •...