Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ACESEE AS-0410
Summary of Contents for ACESEE AS-0410
-
Page 1: User Manual
H.264 NETWORK Embedded DVR User Manual Plastic shell DVR... - Page 2 Thank you for purchase our product. Please read this user manual carefully to ensure that you can use the device correctly and safely. Attentions: ◆The DVR should be installed in a well-ventilated place，keep suitable space from ground ,benefit for machine cooling，Be sure not to block its air vent.，keep away from heat sources and high temperaturea environment。...
-
Page 3: Table Of Contents
CONTENT CONTENT......................3 1. Product Introduction..................3 1.1 Summary....................3 1.2 Main Functions..................4 1.3 Rear panel diagram................4 2. Basic function operation.................6 2.1 On/off Switching navigation..............6 2.2 Login....................... 6 2.3 Main menu setup guide................7 2.4 Configuration management..............9 2.5 Data retrieval..................21 2.6 Backup....................24 2.7 Check information................24 2.8 Disk management................25... -
Page 4: Product Introduction
1. Product Introduction 1.1 Summary This device is a digital monitoring and recording product specially designed for the security field. It adopts standalone processor and standalone Linux operating system. The device combines with the latest technologies in the IT field, such as video and audio compression/decompression, large capacity HDD record, TCP/IP network etc.. -
Page 5: Rear Panel Diagram
1.3 Rear panel diagram Statement(Pictures will be subject to the actual:): pic: the rear panel interface, button layout and type, real product shall prevail. ， below rear panel picture may be different with the actual panel. Connectors on Rear Panel： Item Physical connector Connector description... -
Page 6: Basic Function Operation
2. Basic function operation 2.1 On/off Switching navigation 2.1.1 Start Before start，Please ensure all parts connected well！ Power on Equipment start，POWER indicator light is red. 2.1.2 Power off User can power off the device by using remote controller、keyboard and mouse. 2.1.3 Disconnect the power by keyboard and mouse: Step1: enter into Menu, then select “System Shut Down”... -
Page 7: Main Menu Setup Guide
Icon Motion Timing Sign Manual Alarm Recording detectio recording description record state n state state Live playback Click Playbutton to playback the record enter fast record playback: as lelow picture: User can do concrete operation by click the buttons on screen. 2.3 Main menu setup guide Menu bar: Click right mouse or press ESC button on the front panel, the control bar will display on the bottom of the screen, refer to pic2-2... - Page 8 Pic2-3 Channel choose user could choose 1 channels from 1-4 to show live video.click to save. Click function menu ，will show dialogue frame as Pic 2-4; Pic 2-4 Mian function Click“Config”，display syswindows as pic2-5: Pic 2-5 Configuration management” Press MENU button on the front panel or the same button on remote control, also cuold display the same window.
-
Page 9: Configuration Management
2.4 Configuration management Configuration Management contains nine sub-menu: basic configuration, on-site configuration, video configuration, recording plan, alarm configuration, network configuration, user management, PTZ configuration and advanced configuration. 2.4.1 Basic configuration Click“Basic configuration” ，show window as pic2-6, The basic configuration contains two sub-menu: system date and time system Pic 2-6 System In this interface user can setup the device name, device ID, video format , Video... -
Page 10: Live Configuration
2 ) Time & date Pic 2-7 Time & date Set the date format, time format time zone at the date and time "interface; Note: Click the "Default" button, the system restore the default settings; Click the "Apply" button will save the above settings; Click the "Exit"button to exit the current interface. - Page 11 Tick off camera name and click “Setup” button to display a window as below： Pic 2-9 Live-color adjustment In this interface, user can adjust brightness, hue, saturation and contrast in live; click “Default” button to resort default setting, click “OK” button to save the setting.user can setup all channels with same parameters, please tick off “all”...
-
Page 12: Record Configuration
2.4.3 Record configuration Click“Record configuration” ，enter window as pic2-11： Record configuration includes four sub menus: start, record bit rate, Character overlay. recycle record. 2.4.3.1 Start Pic 2-11 Start Tick off record channel, channel audio. User can setup all channels with same parameters, tick off “All”, then to do relevant setup. - Page 13 2.4.3.2 Record bit rate Pic 2-12 Record bit rate Setup rate, resolution, quality, encode and max bit stream User can setup all channels with same parameters, tick off “All”, then to do relevant setup. Click “Default” button to resort default setting; click “Apply” button to save the setting; click “Exit”...
-
Page 14: Recycle Record
Stamp：User can overlap the channel name and time stamp on video Pic 2-13 Character overlay Tick off camera name, time stamp; click Setting button, and then user can use cursor to drag the camera name and time stamp in random positions. Please refer to below Figures User can also setup all channels with same parameters. -
Page 15: Alarm Configuration
Click “Default” button to resort default setting; click “Apply” button to save the setting; click “Exit” button to exit current interface. 2.4.4.2 Motion Pic 2-15 Motion The setup steps of motion are familiar with schedule Note: the default schedule of motion detection is full-selected, that is, the color of schedule setting interface is blue. - Page 16 2.4.5.2 Motion Motion includes one sub menus: motion 1> Motion Pic 2-21 Motion Click start motion alarm and set alarm hold time， It refers to after close motion alarm it delay to the preset setting time. Click alarm "Settings" button, show below window： Pic 2-22 Alarm handling Alarm configuration, trigger video alarm handling, linkage alarm handling and sensor alarm handling trigger settings is same.
-
Page 17: Network Configuration
set All locales for the detection region；click icon，will clear setting detection region； click icon，save setting；click button,exit from current interface. User can setup all channels with same parameters, please tick off “All”, and then to do relevant setup. Click “Default” button to resort default setting; Click “Apply” button to save the setting; click “Exit”... - Page 18 2.4.6.1 Network Pic 2-27 Network configuration HTTP port：the default value is 80. If the value changed, user needs to add the port number when typing IP address in IE address blank. IE set HTTP port to 82, IP address: http://192.168.0.25 , user needs to input that address: http://192.168.0.25:82 into IE browser.
-
Page 19: Other Settings
options: lowest, lower, low, medium, higher and highest. 2.4.6.3 Email Pic 2-29 Email SMTP Server/Port: the name and port number of SMTP server. Send address/password: sender’s email address/password. Receive address: receiver’s email address. Here user can add at least three mail addresses. -
Page 20: User Management
2.4.7 User management Enter User management , as below pic： Pic 2-31 User management Clicking Add button, a dialog box will pop-up as below： Pic 2-32 General General: Input user name, password; select user type, input the MAC address of the PC;... -
Page 21: Data Retrieval
In the authority interface, assign the definite operation right for that user. In the user management interface, click Setup button to modify user name, user type and binding PC MAC address. Select the user that user wants to delete in the user list box and then click “Delete” button to delete this user. - Page 22 Pic 2-42 Time search Step 2：Select the channel, the calendar date , the start time and end time Step 3：click“Play” button, Playback will start from the set time bucket; click the corresponding button on the screen to start concrete operations. Pic 2-43 Playback buttons...
- Page 23 2.5.2 Event search Step1:：enter into Search configurationevent search; refer to below pic. Pic 2-44 Event search Step2：After clicking Search button, the searched event information will displayed in the event list box, double check a certain record file to playback. Step3：User can select date, channel. Tick off Motion, Sensor or All accordingly to search.
-
Page 24: Backup
2.6 Backup This unit supports backup by USB device，User also can make backup by IE browser via internet. Step1: enter into backup configuration interface, as below pic： Pic 2-45 Data backup Step2: set the start & end time, select channels and click Search button to display the searched data in the data backup list box. -
Page 25: Disk Management
2.8 Disk management Enter menu Disk management，In the interface, the user can view disk storage state, also can choose to formatting the hard disk Please format the hard disk before record ,Specific operation as below：. Step1: enter into disk management interface， The system will pop up the Disk Management window. -
Page 26: Upgrade
2.9 Upgrade Once have the new version, the user can choose to upgrade the panel and the mianboard, can get upgraded software from the buyers, to upgrade the system. Upgrade step：user needs to copy the upgrade software which get from vendor into the USB storage device and then connect to the USB port.