Related Manuals for NNG NTV-KIT558
Summary of Contents for NNG NTV-KIT558
- Page 1 3950 NW 120 Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-Ford V1 Navigation interface for FORD vehicles equipped with 8.4” MyTouch NTV-KIT558 NTV-DOC218...
- Page 2 Page 3 7. Rear-LCD Cable 1. NNG-FORD V1 GPS/Interface 8. GPS Antenna 2. NNG-FORD V1 Internal Modification PCB 9. OEM/NAV Toggle Switch 3. NNG-FORD V1 Plug & Play T-Harness 4. LCD/TP Cables 5. Audio Switch Module 6. Audio I/O Y-Cable...
- Page 3 NTV-DOC218 STOP – Install At Your Own Risk YOU MUST READ THESE WARNINGS AND NOTICE BEFORE PRODUCT HANDLING AND INSTALLATION! PRODUCT AND VEHICLE APPLICATION WARRANTY DISCLAIMER WARNING! The Navigation Electronic Components are sensitive to Electro-Static Discharge (ESD). DO NOT HANDLE THE NAVIGATION ELECTRONIC COMPONENTS WITHOUT PROPER ESD GROUNDING DURING INSTALLATION.
- Page 4 NTV-DOC218 WARNING To avoid dangerous distractions that may lead to an accident, the driver should never operate the system while the vehicle is in motion. Before installing this product, the seller should inform the end-user of proper use and compliance with the proper instructions and all state and federal laws.
- Page 5 NTV-DOC218...
- Page 6 NTV-DOC218...
- Page 7 NTV-DOC218...
- Page 8 NTV-DOC218...
- Page 9 NTV-DOC218...
- Page 10 NTV-DOC218...
- Page 11 NTV-DOC218 Page 10...
- Page 12 NTV-DOC218 Page 11...
- Page 13 NTV-DOC218 Page 12...
- Page 14 NTV-DOC218 Mount the GPS antenna to the top-rear of the vehicle allowing it to attach using its magnetic base. Route the GPS antenna extensions harness to the front Connect the TP-IN and LCD-IN harness to the PINK of the vehicle above the headliner, down the and YELLOW ports on the navigation control module.
- Page 15 NTV-DOC218 Connect the power harness from the vehicle interface Connect the speaker interface harness to the harness to the navigation control module. navigation control module. Find the threaded end of the GPS antenna and connect Connect the vehicle interface harness to the factory it to the navigation control module.
- Page 16 NTV-DOC218 Apply double sided tape (or equivalent) to the bottom Attach the navigation control module to the dashboard side of the navigation control module. in the open cavity below the factory CD player. Attach the vehicle interface harness to the backside of Connect the TP-IN and LCD-IN harnesses previously the touch screen unit.
- Page 17 NTV-DOC218 Replace the touch screen unit and factory CD player. If indoors, start the vehicle and move it outside so that the GPS antenna has a clear view of the sky. Press the Make sure no wires are pinched in the process. mute/call decline button to switch from the factory interface to the iGo Navigation interface.
- Page 18 NNG-FORD V1 Wiring Diagram Page 16...
- Page 19 Ford Audio Integration Components for audio integration: GPS Audio Box Wiring (FD-AUDSPK-02) Wiring (AUD-6PIN-01) Main Harness (same harness used in main install) Rear-LCD (connected to GPS box from main install) Steps: Connect both FD-AUDSPK-02 and AUD-6PIN-01 to GPS Audio Box Connect white, 2-PIN power plug to power from main Interface harness 2-PIN power Insert green wire with pin to Main Harness (See figure 1) green wire from...
-
Page 20: Gps Monitor
WEAK /NO GPS SIGNAL? Tips to Improve GPS Antenna Signal if vehicle equipped Metallized Windshield* “GPS MONITOR Tools” Exit IGO MAP by press SHUT DOWN BUTTON Console> SETUP GPS MONITOR Locate the Antenna with minimum 5 bars in dark blue or Gray bar (Always suggest mounting the GPS antenna on the roof) Press “!”... - Page 21 PROPER GPS ANTENNA POSITION if vehicle equipped *Metallized Windshield Sedan SUV/Coupe TRUCK (Shown as Tundra) Alternatively, installer might choose to mount Antenna inside the headliner or inside vehicle using GPS monitor tools (see instruction). However, stay away from the windshield. * Windshields with metal particles can interfere with radio waves, dash-mount satellite radio receivers, and GPS receivers may be affected external transmitters and receivers may be required.