Meccanica Benassi F 213 User Manual
  1. Manuals
  2. Brands
  3. Meccanica Benassi Manuals
  4. Lawn Mower
  5. F 213
  6. User manual

Meccanica Benassi F 213 User Manual

Motormower
Hide thumbs
Table of Contents

Advertisement

Quick Links

GB
MOTORMOWER F 213
READ THIS MANUAL CAREFULLY
All right reserved
This manual cannot be either reproduced or released without the
manufacturer's prior written consent.
PRINTED IN ITALY
1 - FOREWORD
This symbol is used to highlight an important safety information. If
this information is ignored, people are in danger either of possible
injures – even serious ones – or death.
IMPORTANT
This term highlights special precautions to be taken in order not to
damage the machine.
The machine serial number is printed on the drive box.
Always mention the machine serial number when calling our technical service or when ordering spare parts.
The CE mark is on the engine support right side.
USER'S MANUAL
2 – IDENTIFICATION AND MARKING
IMPORTANT NOTE
USER'S MANUAL
1.
FOREWORD
2.
IDENTIFICATION AND MARKING
3.
CONDITIONS AND USE
4.
WARRANTY
5.
VIBRATIONS-NOISE-STABILITY
6.
WARNING SIGNS
7.
SAFETY WARNINGS
8.
TECHNICAL DATA
9.
DIMENSIONS – MEASUREMENTS
10. DESCRIPTION OF CONTROLS
11. MACHINE PREPARATION
12. STARTING OF THE MACHINE
13. WORK STARTING/STOPPING
14. MAINTENANCE - LUBRICATION
15. TROUBLES AND SOLUTIONS
16. RULES FOR A GOOD WORK
17. DECLARATION OF CONFORMITY
ENGINE :Use and maintenance instructions of the engine
are mentioned in the relevant manual, copy of which is
always supplied with every machine.
MARKING
Marking example.
07/05
Pag. 0
Pag. 0
Pag. 1
Pag. 1
Pag. 2
Pag. 2
Pag.3-4
Pag 5
Pag.5
Pag .6
Pag. 7
Pag. 8
Pag. 8
Pag. 9
Pag. 9
Pag.10
Pag.10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the F 213 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Meccanica Benassi F 213

Summary of Contents for Meccanica Benassi F 213

  • Page 1 07/05 USER’S MANUAL MOTORMOWER F 213 USER’S MANUAL FOREWORD Pag. 0 IDENTIFICATION AND MARKING Pag. 0 CONDITIONS AND USE Pag. 1 WARRANTY Pag. 1 READ THIS MANUAL CAREFULLY VIBRATIONS-NOISE-STABILITY Pag. 2 WARNING SIGNS Pag. 2 All right reserved SAFETY WARNINGS Pag.3-4...

  • Page 2: Warranty

    The Manufacturer reserves the right to make any change Descriptions, figures and technical features mentioned at any time without being bound to update this herein are non-binding for the Manufacturer. These are publication. mentioned as mere information. Copyright of MECCANICA BENASSI S.P.A.” - 1 -...

  • Page 3: Warning Signs

    5 – VIBRATIONS – NOISE - STABILITY IN CASE OF CONTINUOUS USE OF THE MACHINE IT IS RECOMMENDED THAT PROTECTIVE HEARING EQUIPMENT IS USED. VIBRATIONS The vibrations of the machine have been taken according to the bill EN 709 and EN 1033 The values obtained in m/sec.

  • Page 4: Safety Warnings

    7- SAFETY WARNINGS Before the machine is operating, read the Use and Maintenance manual thoroughly, so that you are fully aware of all the operating controls and safety aspects of the machine. Before starting the engine , be sure that the SAFETY DEVICES are well working and fitting. Without these cares the operator might work in a danger situation.
  • Page 5 17) Do not run the machine in a confined area as toxic exhaust gas can kill. 18) Plan your work before commencing. 19) Do not use the machine when you are tired. 20) Engage the clutch gradually; sudden engagement could cause the machine to rear up. 21) The area next to the engine exhaust will most likely reach temperatures above 80°.

  • Page 6: Technical Data

    8 – TECHNICAL DATA ENGINE 4 STROKE on the belt with idler CLUTCH single speed with wheels disengagement GEAR BOX 1090 r.p.m with left (Sx) rotation P.T.O height adjustable on revolving vibrations dampers HANDLEBARS 3.50.06 tyres WHEELS Complete machine about kg.56 WEIGHT ACCESSORIES ESM cutter bar 81 cm with eccentric movement...

  • Page 7: Description Of The Controls

    10 – DESCRIPTION OF THE CONTROLS 1 WHEEL DISENGAGE LEVER Located on the right handlebar; it is necessary to disengage the wheels from the transmission. In “off” position ( RAISED LEVER wheels Pic. 1 engaged when the lever is depressed the wheels are disengaged.

  • Page 8: Machine Preparation

    . 3 ) . 4) LEVERS PLACED ON THE HANDLEBARS HANDLEBAR POS AND POS AND PTO ROD USED IN THE DIFFERENT POSITIONS LET • displace the machine in quiet both with engine in motion or stop • operate the cutter bar with idle wheels •...

  • Page 9: Starting Of The Machine

    12 – STARTING OF THE MACHINE Before using the machine make sure you have understood all the instructions contained in this manual. Before starting the machine always check: - the oil levels in the engine and reducer case with proper dip-stick; - the air filter is well clean both inside and outside: brushwood and leaves near the filter could burn if they enter into contact with the superheated head of the cylinder - the tyres are at the right pressure ( 1.3 Bar) and correctly turned...

  • Page 10: Maintenance And Lubrication

    14 – MAINTENANCE and LUBRICATION To optimise the efficiency of the machine it is necessary to maintain the machine correctly and to ensure the engine is fully lubricated. The machine is normally supplied packed without oil in the engine, as clearly indicated on the label attached to the engine.

  • Page 11: Declaration Of Conformity

    - GB - CE – DECLARATION OF CONFORMITY In compliance with CEE 89/392 regulations and subsequent changes MECCANICA BENASSI S.p.A , I-44040 DOSSO (FE) via Statale, 325 DECLARES, under is own responsibility, that the item called MOTORMOWER Model: From series-no.:...

Table of Contents