LOCATIONS Corporate Head Quarters Middle East E-PoS International LLC Tel: +9714-3523288 / 3512861 P.O.Box 12608 Fax: +9714-3513396 Dubai, UAE Email: eposintl@emirates.net.ae South East Asia Head Quarters South East E-PoS International Tel: +91-253-2411806 Asia Nasik-Pune Road Fax: +91-252-2415295 Ayodhya Nagri Email: pradeepw@sancharnet.in...
DO’S & DON’TS (Integrated circuits on All E-PoS System boards are sensitive to static electricity. To avoid damaging any Components on the computer board, before getting started, read these following precautions and other instructions and save them for later reference).
ACCESSORIES 1. Warranty Card. 2. Power Cable. 3. Driver Bank CD. 4. External Floppy Disk Cable. 5. External IDE Cable. 6. Keys. The following drivers in the folders of Drivers Bank are necessary for driver installation: Folder Driver Function Acrobat Acrobat Reader Installation BIOS Tool BIOS Update Tool...
INPUT / OUTPUT FUNCTIONS 2.1 Front View 2.2 Rear View Function Function Function Function USB 1 & 2 COM3 Compact Flash Printer AC Power COM4 Keyboard COM2 Power Fan External FDD Mouse COM1 16 External CD-ROM •...
PERIPHERALS INSTALLATION 4.1 Install External FDD Use the floppy cable from the accessory bag to connect the floppy disk drive to the system bay module. 4.1.1 Enable FDD BIOS Setup Enter "Standard CMOS Features" of the b. Move the arrow key downward to the Main Menu of BIOS CMOS Setup Utility.
Page 9
4.2 Install External IDE Device Connect the IDE cable from either the second HDD or CD-ROM drive to the 50 pin Header hidden in the Front Cover of the Base Stand. 4.3 Install MCR Module (optional) The optional MCR is removed during transportation and can be connected by the user. The manufacturer offers two types of MCR Module: Serial type or keyboard type.
For serial type MCR, CN3 on keyboard type cable the function board is disconnected. If you choose keyboard type MCR, use the keyboard type cable to connect the CN3 on the function board. CN3(function board) For serial type MCR, JP1 on the function board is set as closing 3-4 and 7-8.
4.4 Install a Compact Flash Card You can install a CF card into the Compact Flash slot. 4.5 Install Cash Drawer(optional) a. We provide a Cash Drawer Control b. Loosen a screw ot one side of the Box for Cash Drawer installation. Box…...
Page 12
g. Our factory default for Cash Drawer power source is set to close JP2(through the DIO cable), but if you want to acquire power from an external source, close JP1 as the picture shows. Now you can start connecting the Cash Drawer with the POS system.
Page 13
4.5.1 DIO port Pin Assignment Data in Address(206h) Data Out Address(206h) 4.5.2 Digital Output Programming The output is TTL Level. The output signal must be TTL compatible. Output Address Out 0 0(customer define) Out 1 1(default) Out 2 2(customer define) Out 3 3(customer define) 4.5.3 Digital Input Programming...
Page 14
4.6 Install Customer Display Module (optional) RJ-45 Cable Customer Display cover kit a. Remove the Customer Display cover kit b. Make the RJ-45 cable go through the from the system base. system base. Supporter buttom Pole support c. Install the supporter bottom onto the cover d.
Page 15
screw bolt g. Now the Customer Display is in an erect h. Insert the screw bolt into the supporter position. top. i. Fasten the nut of screw bolt. j. Connect the RJ-45 cable to COM2 (default). For COM2 connection, default pin 5 and pin 6 of JP3.
DRIVER INSTALLATION The following procedures are for Windows 98. Other platforms are similar. 5.1 Elo_Touch a. Click "COMMON" on the POS driver window. b. Click "Elo_Touch" on the COMMON c. Choose the OS to be installed with Elo window. _Touch driver. d.
Page 18
f. Click “Next” on the Elo MonitorMouse for g. Choose “COM3” and click “Next” on the Windows 95/98 Setup window. Elo MonitorMouse for Windows 95/98 Setup window. h. Click “Yes” on the System Settings i. After the computer restarted, touch the Change.
Page 19
m. Now the Elo_Touch driver is installed. l. If the cursor is not lined up with your finger, click “Align…” to execute the alignment procedure again, or click “OK” 5.2 LAN a. Click "COMMON" on the POS driver window. b. Click “Lan_driver” on the COMMON c.
Page 20
REL8139_810x window. window. g. Click “Browse” on the Insert Disk window. f. Click “Next” on the InstallShield Wizard. h. Point out the exact location of the new i. Click “OK” on the Insert Disk window. LAN driver and click “OK”. j.
Page 21
5.3 VGA a. Click “My Computer” on the desktop by the right key of the mouse and then click “Properties” by the left key of the mouse. b. Click “Device Manager” on the System Properties” window. c. Click “Display adapters” and you will not d.
Page 22
f. Click “Next” on the Add New Hardware Wizard window. e. Click “Driver” and then click “Update Driver…” on the Standard PCI Graphic Adapter (VGA) window. g. Choose “Search for the best driver for h. Click “Browse” on the Add New your device”...
Page 23
i. Point out the exact location of the new j. Click “Next” on the Update Device Driver VGA driver and click OK. Wizard window. k. Click “Next” on the Add New Hardware l. Click “Finish” on the Add New Hardware Wizard window.
Page 25
6.2 Watch Dog Timer Settings: JP1 (On slot card FT-7364) Time 0.1 sec 0.5 sec 1.0 sec 1.6 sec 10 sec 1 min 10 min 6.2.1 Watch Dog Timer Programming: Input / Output Address Function Output 205H Watch Dog ON Input 205H Watch Dog WDI...
Page 26
66MHz Close Open Open Open Close 6.10 CMOS Operation Mode Function JP12 *CMOS Normal CMOS Reset ________________________________________________________________________ E-Pos International L.L.C, P. O. Box No. 12608, Dubai, U. A. E, Tel. No. (+9714) 3523288, Fax. No. (+9714) 3513396, E-Mail: eposintl@emirates.net.ae ••...