1. Manuals
  2. Brands
  3. Maretron Manuals
  4. Wireless Router
  5. Linksys E2000
  6. Configuration manual

Maretron Linksys E2000 Configuration Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Linksys E2000 Wireless-N Router Configuration Guide
http://www.manuallib.com/file/2601646
From ManualLib.com
ManualLib.com collects and classifies the global product
instrunction manuals to help users access anytime and
anywhere, helping users make better use of products.
Home: http://www.manuallib.com/ Chinese: http://www.shuomingshuku.com/
This Manual: http://www.manuallib.com/file/2601646

Advertisement

Table of Contents
loading

Summary of Contents for Maretron Linksys E2000

  • Page 1 Linksys E2000 Wireless-N Router Configuration Guide http://www.manuallib.com/file/2601646 From ManualLib.com ManualLib.com collects and classifies the global product instrunction manuals to help users access anytime and anywhere, helping users make better use of products. Home: http://www.manuallib.com/ Chinese: http://www.shuomingshuku.com/ This Manual: http://www.manuallib.com/file/2601646...

  • Page 2: Configuration Guide

    ® ® Linksys E2000 Wireless-N Router ® Configuration Guide Revision 1.0 Copyright © 2011 Maretron, LLP All Rights Reserved Maretron, LLP 9014 N. 23 Ave #10 Phoenix, AZ 85021-7850 http://www.maretron.com Maretron Manual Part #: M003009 Revision 1.0 Page 1 This Manual: http://www.manuallib.com/file/2601646...

  • Page 3: Revision History

    Linksys® E2000 Wireless-N Router Configuration Guide Revision History Rev. Description Original document Page 2 Revision 1.0 This Manual: http://www.manuallib.com/file/2601646...

  • Page 4: Table Of Contents

    Adding a Wireless PC N2KView Client to the Network ........... 16   Adding a Mobile N2KView Client to the Network ............ 16       Resetting the WiFi/Router to Maretron Configuration ............17   Physically Reset the WiFi/Router ................17     Give your Wireless Network a name ..............17  ...

  • Page 5: Introduction

    USB gateway (USB100)). Figure 1 shows a typical configuration where multiple devices ® running Maretron’s N2KView software (e.g., laptop computer, desktop computer, smart phone, tablet, Maretron DSM800 display, or Maretron MBB100 black box) are connected back ® to an NMEA 2000 network through the WiFi/Router and the Maretron Internet Protocol Gateway (IPG100).
  • Page 6 ® ® Although the WiFi/Router is mostly pre-configured by Maretron, there are a few steps that must ® be performed to establish the connection between Maretron’s N2KView vessel monitoring ® and control software (client) and Maretron’s N2KServer (server). If you are installing a system ®...

  • Page 7: Configuring The Wifi/Router

    Linksys® E2000 Wireless-N Router Configuration Guide Configuring the WiFi/Router The settings in the WiFi/Router are changed using a web browser such as Internet Explorer, Safari, or Mozilla Firefox. Connecting to the WiFi/Router Connect the WiFi/Router to your PC using the blue Ethernet cable supplied in the box. Use the supplied AC adapter to power the WiFi/Router.
  • Page 8 ® ® From now on, we will just show the screens from Firefox – the screens from other browsers will be very similar. Leave the User name blank, and enter the default Password, which is admin and press the OK button. You may see the following message: Cisco connect is a utility that comes with the router.
  • Page 9 Linksys® E2000 Wireless-N Router Configuration Guide You are now connected to the WiFi/Router, and should see the following basic setup screen. Page 8 Revision 1.0 This Manual: http://www.manuallib.com/file/2601646...

  • Page 10: Adding An Ipg100 To The Network

    Adding an IPG100 to the Network. Connect Maretron’s Internet Protocol Gateway (IPG100) to the WiFi/Router using an Ethernet Cable. The cable plugs into one of the blue Ethernet sockets at the back of the router. Reset the IPG100 by removing the NMEA2000 cable and re-attaching it. This forces the IPG100 to connect to this router, and removes previously allocated addresses.
  • Page 11 Linksys® E2000 Wireless-N Router Configuration Guide From the Basic Setup page, open the DHCP Reservation Table by pressing the DHCP Reservation button. The DHCP Reservation table is displayed as shown below: If you do not see an IPG100 in the top part of the table, then it has not requested an address from the DHCP Server.
  • Page 12 ® ® Carefully copy the Client Name and MAC Address for the IPG100 from the top table to the second table. Set the assigned IP Address for the IPG100 to 192.168.1.3. Press Add Clients to add the IPG100 to the table: Press Save Settings and then Close.

  • Page 13: Adding A Pc Based N2Kserver ® To The Network

    , then each one must have a unique reserved address, but this is beyond the scope of these instructions, so please contact Maretron Technical Support for assistance. Inside the WiFi/Router is a DHCP Server, which is responsible for assigning IP addresses to other network devices that request them.
  • Page 14 ® ® The DHCP Reservation table is displayed as shown below: Carefully copy the Client Name and MAC Address for the PC from the top table to the second table. Set the assigned IP Address for the PC to 192.168.1.3. Revision 1.0 Page 13 This Manual: http://www.manuallib.com/file/2601646...

  • Page 15: Adding A Mbb100 N2Kview Client To The Network

    PC is given its new address. Adding a MBB100 N2KView Client to the Network Connect Maretron’s Black Box (MBB100) to the WiFi/Router using an Ethernet Cable. The cable plugs into one of the blue Ethernet sockets at the back of the router.

  • Page 16: Adding A Dsm800 N2Kview Client To The Network

    ® ® If the default values are used this should be 192.168.1.3. A message should be displayed at the bottom left of the section stating that an IPG100 or N2KServer has been found, and giving its IP Address. Press the Connect button to establish the connection. Adding a DSM800 N2KView Client to the Network Connect the DSM800 to the WiFi/Router using an Ethernet Cable.

  • Page 17: Adding A Wireless Pc N2Kview Client To The Network

    Linksys® E2000 Wireless-N Router Configuration Guide Adding a Wireless PC N2KView Client to the Network Using the Wireless Configuration programs supplied with the PC, connect to the Wireless Network identified by the SSID written on the label affixed to the bottom of your router. When prompted to enter the passphrase, enter the passphrase from the same label.

  • Page 18: Resetting The Wifi/Router To Maretron Configuration

    In addition to the parameters that must be set by the user described in paragraph 2, several parameters are set by Maretron at the factory. If the factory settings are ever lost, then you can reset the WiFi/Router and program the factory setting by following the instructions outlined in the following paragraphs.

  • Page 19: Programming Network Security

    Linksys® E2000 Wireless-N Router Configuration Guide In the Network Name (SSID) field, replace the word Cisco with Maretron, leaving the 5 digits from the serial number intact. Programming network security This section details the programming of WiFi/Router to ensure that wireless messages to and from the router are encrypted against eavesdropping.

  • Page 20: Appendix A- Client/Server Architecture

    N2KView software may run on a ® ® Windows PC, Mac, or Maretron ’s MBB100 or DSM800. Mobile versions of N2KView software are available for iPod Touch, iPhone, iPad and most Android devices. The service ® offered by the server to the stations (clients) is access to the NMEA 2000 network data that ®...

  • Page 21: Examples Of Nmea 2000® Client/Server Architectures

    Linksys® E2000 Wireless-N Router Configuration Guide A.1 Examples of NMEA 2000® Client/Server Architectures ® N2KServer may run on a Windows PC (using Maretron’s USB100 gateway - see and ) or ® N2KServer may run directly on an IPG100 (see Figure 2).

  • Page 22: Tcp/Ip Networks

    ® ® Figure 3 extends the example shown in by adding an external internet access point across a Wide Area Network (WAN). Although it is possible to setup the network as shown in , ensuring ® ® that the remote N2KView clients can find the IP Address of the N2KServer at the correct port (6543 or 6544) requires considerable IT expertise.

  • Page 23: Nat (Network Address Translation)

    Linksys® E2000 Wireless-N Router Configuration Guide typically found as part of a router. The router can be configured to reserve a specific address for the computer and then assign that same address each time at startup. If the router chooses a different address each time, then the computer may be difficult to find on the network.

  • Page 24: Static And Dynamic Ip Addressing

    ® ® ® N2KView must then be set up to request a connection to the WAN IP Address of the router and the new port number. A.5 Static and Dynamic IP Addressing ® ® If you wish to use N2KView to view data from an N2KServer on a WAN through an Internet ®...
  • Page 25 Linksys® E2000 Wireless-N Router Configuration Guide ® The N2KView system protects your vessel’s data with multiple levels of protection. ® ® First, any data that passes between the N2KServer server component and any N2KView station components is protected using industry-standard SSL encryption. This encryption standard is widely used to protect financial information on the internet.

Table of Contents