Gioteck FR-1 Manual

FR-1
prEcautions
This product has been designed with the
highest concern for safety. However, any
electrical device, if used improperly, has
the potential to cause harm. To help ensure
risk-free operation please pay attention to the
FREEDOM RACING WHEEL
following guidelines.
FOR PLAYSTATION 3™
• Use only as intended. This is a precision
product, handle with care.
Thank you for purchasing the • Contains small parts. Not suitable for
children under 3 years of age.
FR-1 Freedom Racing Wheel
• Store in a dry & dust free area.
from Gioteck.
• Do not store in areas of extreme heat or
cold, and avoid direct sunlight or heat
We hope that this product will
sources eg. heaters.
• Do not allow the product to get wet or dirty;
go beyond your expectations for
doing so may cause damage.
a quality made accessory.
• Do not clean with benzene, paint thinner,
acetone, alcohol, or other such solvents.
Please read this booklet
• Do not take the product apart; doing so will
thoroughly before using the void your warranty and may cause
electrical shock.
product and review the PS3™
manual for additional details
warnings
regarding PS3™ operation.
Always follow these instructions
closely. This symbol indicates
Thank you & enjoy! important installation, operational or
maintenance instructions.
gb
01 | Directional Pad
02 | Action Buttons
03 | Home Button
01
04 | Select Button
05 | Start Button
06 | Channel LED
07 | Power LED
08 | Sensitivity Switch
03
09 | R2 Button
04
10 | L2 Button
11 | X Trigger
12 | Trigger
13 | R1 Button 06
14 | L1 Button
15 | Mini USB Port
16 | Battery Compartment
17 | USB Dongle
07
Fr DE
01 | Steuerkreuz
01 | Pad directionnel
02 | Boutons d'action 02 | Aktionstasten
03 | Bouton Home 03 | Home-Taste
04 | Bouton Sélection 04 | Select-Taste
05 | Bouton Démarrer 05 | Starttaste
06 | Canal DEL 06 | Kanal-LED
07 | Alimentation DEL 07 | Stromversorgungs-LED
08 | Interrupteur de sensibilité 08 | Empfindlichkeitsschalter
09 | Bouton R2 09 | R2-Taste
10 | Bouton L2 10 | L2-Taste
11 | Gâchette X 11 | X Trigger
12 | Gâchette 12 | Trigger
13 | Bouton R1 13 | R1-Taste
14 | Bouton L1 14 | L1-Taste
15 | Mini port USB 15 | USB-Minianschluss
16 | Compartiment à piles 16 | Batteriefach
17 | Branchement USB 17 | USB-Dongle
Es it
01 | Control de dirección 01 | Pad direzionale
02 | Botones de acción 02 | Pulsanti di comando
03 | Botón Inicio 03 | Pulsante Home
04 | Botón Selección 04 | Pulsante di selezione
05 | Botón Start 05 | Pulsante di avvio
06 | LED de canales 06 | LED canale
07 | LED de encendido 07 | LED alimentazione
08 | Selector de sensibilidad 08 | Interruttore sensibilità
09 | Botón R2 09 | Pulsante R2
10 | Botón L2 10 | Pulsante L2
11 | Disparador X 11 | Trigger X
12 | Disparador 12 | Trigger
13 | Botón R1 13 | Pulsante R1
14 | Botón L1 14 | Pulsante L1
15 | Puerto miniUSB 15 | Porta USB Mini
16 | Compartimento de baterías 16 | Vano batterie
17 | Llave (dongle) USB 17 | Dongle USB
EnvironmEnt
Please help to conserve the
environment by recycling the
cardboard packaging of this product.
This product should NOT be disposed
of in normal household waste. It should
be disposed of separately. Please take
it to an electrical waste collection point.
lEgals
This product complies with the following legal
regulations. For further information go to
www.gioteck.com
Gioteck hereby declares that this
controller is in compliance with the
essential requirements and other provisions
of Directive 2004/108/EC. To view the full
version of the Declaration of Conformity
please go online to doc.gioteck.com
Caution: The user is cautioned that changes
or modifications not expressly approved by the
party responsible for compliance could void
the user's authority to operate the equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept
08
02
05
17
09 10
11 12
13 14
15
16
pt cZ
01 | Control de dirección 01 | Ovladač směru
02 | Botones de acción 02 | Akční tlačítka
03 | Botón Inicio 03 | Tlačítko pro návrat
04 | Botón Selección 04 | Tlačítko pro výběr
05 | Botón Start 05 | Tlačítko start
06 | LED de canales 06 | LED pro kanál
07 | LED de encendido 07 | Napájecí LED
08 | Selector de sensibilidad 08 | Tlačítko pro citlivost
09 | Botón R2 09 | Tlačítko R2
10 | Botón L2 10 | Tlačítko L2
11 | Disparador X 11 | X Spoušť
12 | Disparador 12 | Spoušť
13 | Botón R1 13 | Tlačítko R1
14 | Botón L1 14 | Tlačítko L1
15 | Puerto miniUSB 15 | Port USB Mini
16 | Compartimento de baterías
16 | Oddíl pro baterie
17 | Llave (dongle) USB 17 | Bezpečnostní klíč USB
sEt up
any interference received, including interference
that may cause undesired operation. Note:
1) Plug the USB Dongle into USB Port #1
This equipment has been tested and found
on the PS3 console.
to comply with the limits for a Class B digital
2) Turn on the console.
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
3) Open the battery compartment and
protection against harmful interference in a
insert 2 x AA batteries.
residential installation.
This equipment generates, uses and can 4) Press the "Home" Button to power
radiate radio frequency energy and, if not
on the Freedom Racing Wheel.
installed and used in accordance with the
5) The FR-1 will automatically select a
instructions, may cause harmful interference
to radio communications. However, there is no channel and an LED will light.
guarantee that interference will not occur in a
6) Now you can enjoy all of your racing
particular installation. If this equipment does
games with a Gioteck Freedom Wheel!
cause harmful interference to radio or television
reception, which can be determined by turning
Press & hold the "Home" button
the equipment off and on, the user is encouraged
for 5 seconds to activate pairing
to try to correct the interference by one or more
at any time.
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
motion stEEring control
1) Tilt the wheel above 30° to activate
motion sensing steering technology.
2) Turn 120° Left/Right for an effective
steering angle. (Note: If you turn the
30˚
wheel more than 120°, the steering will
default back to the neutral position.)
3) Tilt between 30° to 145° horizontally for
an effective operational angle.
Lay the FR-1 flat during menu
operation to prevent motion
sensor interference.
TILT TO ACTIVATE
MOTION SENSING
115˚
EFFECTIVE TILT ANGLE EFFECTIVE TURNING ANGLE
motion sEnsing moDE motion sEnsing calibration
The default setting for the Motion Sensing To calibrate your FR1 follow the
Mode is the Left 3D Stick. instructions below:
To change Motion Sensing from the 1) Place it on a flat surface.
Left 3D Stick to Six Axis Mode:
2) Press and hold the "Select" & "Home"
1) Press and hold "Select" with "the down buttons simultaneously for 5 seconds
arrow on the D-Pad" for 5 seconds.
3) All four channel LED's will light.
2) The Power LED will flash slowly
4) Press the "Start" button to calibrate.
3 times to indicate the change.
5) Once calibration is complete,
3) To change back to the default setting,
the LED's will turn OFF and the
repeat the process above.
assigned channel LED will light.
Note: Once the power is off,
all program settings will
reset to default.
opEration
POWER ON
To turn on the FR-1, press Home button
once and the LED will light.
POWER OFF
To turn off, press & hold "Select" & the
"O" button simultaneously for 5 seconds.
FR-1
Note: The FR-1 will automatically turn
off if it is disconnected from the PS3
for 30 seconds or more.
SLEEP MODE
FREEDOM
The FR-1 will enter sleep mode if it is
inactive for 5 minutes. To exit sleep
RACING WHEEL
mode, press Home button once.
FOR PS3™
SENSITIVITY ADJUSTMENT
To adjust the sensitivity, slide the
Sensitivity Switch to your desired level.
Note: Sensitivity Adjustment does
not work during Six Axis Mode.
LOW BATTERY
The Channel LEDs will flash rapidly
when the battery charge is low. You will
need to replace with new batteries.
rEassigning X & triggErs
The default keys for the Trigger Pedals
□
are the X Trigger & Trigger. To change
the Trigger Pedals to the R2 Button &
L2 Button:
1) Press and hold the "Select" & "Start"
buttons simultaneously for 5 seconds.
2) The power LED will flash slowly 3 times
to indicate the change.
3) To change back to the default setting,
repeat the process above.
Note: Once the power is off,
all program settings will
reset to default.
120° STEERING TO THE LEFT 120° STEERING TO THE RIGHT
troublEshooting
i) In some games the racing wheel
must be assigned to Port 1.
To assign The FR-1 to Port 1, press and
hold the "Home" button. The Channel
LED will indicate when the channel
assignment is successful.
ii) The Pedals do not seem to work.
Make sure the trigger pedals have not
been reprogrammed – Please follow the
instructions in the "Reassigning Trigger
Pedals" section.
For further assistance please contact
our customer support team on our
website: www.gioteck.com
.