LuguLake T-180BT User Manual

/ Q %H X L /L
To Lugulake Customer:
We are always here to solve your problem.
Contact us, we will respond
you within 24 hours.
Email : support@lugulake.us
Tel: 1-626-244-8606
Website: www.lugulake.us


ASSEMBLY AND SAFETY

The remote control contains a button cell.Please always keep the remote control and the button
Please read the following instructions before assembly:
cell out of reach of children.
The Soundbar is designed for audio playback.All other uses are expressly excluded.
If the button cell is accidentally swallowed, it can lead to burns and even death within two hours.
If you want to set up the Soundbar on shelving units, in cupboards, etc., please ensure that there is
You should therefore see a doctor immediately.
adequate ventilation. There must be a free area of at least 10 cm on either side and above the
Keep new and used batteries out of reach of children. If the battery compartment cannot be closed
Soundbar.
safely,do not continue to use the device and keep out of reach of children.
Do not cover the Soundbar with newspapers,tablecloths, curtains, etc.
Remove the battery if used up or if you do not use the device for a long time. We do not assume
When setting up the Soundbar, please note that furniture surfaces may be covered with various
liability for damage caused by leaked batteries.
finishes or synthetic materials that often contain chemical substances. These substances can attack
The batteries, even those free from heavy metals,must not be disposed of as domestic waste.Used
the material of the unit base among other things. This can leave residues on the furniture surface,
batteries must be discarded in used battery collection containers found at commercial or public waste
which may be difficult or impossible to remove.
management services.
If the Soundbar is subjected to big variations in temperature, for example when transported from a
You must never open the Soundbar. In case of damage due to improper tampering, any claims for
cold to a warm place, do not use the Soundbar for at least two hours.
guarantee are lost.
The Soundbar is designed to be used in dry rooms. Should you nevertheless decide to operate it
Storms are a danger to any electronic device.Even if the Soundbar is switched off, it may still become
outdoors, you must ensure that it is protected from moisture (dripping or splashing water).
damaged as a result of lightning striking the mains. In case of a storm, you must always pull the mains
Only use the Soundbar in a temperate climate.
plug.
Do not place the Soundbar close to a radiator or in direct sunlight; this can affect the cooling system.
Notes:
Do not place any containers with liquids inside (e.g. vases) on top of the Soundbar.
Do not connect any devices when your device is switched on. Also switch the other devices off before
Do not place any open sources of fire (e.g. candles) on top of the Soundbar.
connecting them!
Do not use any cleaning agents; these may damage the casing. Cleanse the device using a clean and
Do not plug the mains plug of your device into the socket until all external devices have been
dry cloth.
connected!
Do not expose the battery to extreme heat,such as for example sunlight, radiators, fire, etc.
Please ensure that the mains plug is freely accessible!

Switches the device on and off.
RF Exposure Warning
220-240V Mains cable.
This equipment must be installed and operated in acordance with provided manual. The device
50/60Hz 0.1A
comprised a built-in antenna, and must not be co-located or operating in conjunction with any other
Note:
antenna or transmitter.
The Soundbar is only completely separated from the mains once the mains plug has been pulled.
See the figure on page 3.
Remote control buttons
Controls are on the front page
LED,
– lights up red whenever the device is in standby mode;
– lights up white if the source device "TV" has been selected.
– lights up orange if the source device "Aux In" has been selected.
3D Activates stereo spread.
– Flashes red when the sound is muted.
Switches the device on from standby mode and back off again. AUX Selects the source device connected to the »AUX IN« jack.
TV Selects the source device "TV" (in the jack »RCA INPUT«).
Increases the volume.
Volume change.
Decreases the volume.
Press briefly to select the source device "TV", "external device" and "Bluetooth".
Press and hold to start Bluetooth pairing; the display B flashes rapidly.
LED flashes rapidly during the Bluetooth pairing process.
PREPARATION/CONNECTION
Connection jacks and controls on the back page
Preparation
Audio signal input (ø 3.5 mm) for connecting an external device.
Activate the remote control battery
Audio signal input (Cinch) for connecting the LCD TV.
1 Remove protection film from the battery compartment.
Audio signal output (Cinch) for an external subwoofer.
– The remote control is now functional.


Change remote control batteries (TYPE CR 2025)

An external device, such as a MP3-Player for example,can be connected to the »AUX IN« jack.
Note: 1 Connect a standard audio lead to the »AUX IN« jack of the Soundbar.
If your device no longer responds to the remote control commands, the battery may be dead. It is 2 Connect adapter cable to the external device.
imperative that dead batteries be removed. We do not assume liability for damage caused by leaked Note:
batteries. The LCD TV can also be connected via the »AUX IN« jack if it is not equipped with audio output jacks.
Caution: In such cases please use the headphone jack.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Connect mains cable
1. Hold the remote control with the back side facing up. Check that the mains voltage indicated on the type label (on the back of the device) corresponds to the
2. Push the detent of the battery holder to the right and remove battery holder. local mains voltage.
3. Remove used battery and insert new battery into the battery holder, positive pole facing upward. If this is not the case, please consult your specialist dealer.
4. Push battery holder into the remote control until it clicks into place. 1 Plug mains cable plug into the socket (220-240V~50/60Hz).

Connecting

Caution:
Connect Soundbar to the LCD TV The Soundbar is connected to the mains via the mains cable. If you want to disconnect the Soundbar
1 Connect a standard audio lead to the from the mains completely,you must pull the mains plug.
Please ensure that the mains cable is freely accessible during operation and is not obstructed by any
»RCA INPUT« jacks of the Soundbar.
– Please be aware of the left and right channels when doing so (white = left channel,red = right channel). other objects.
2 Connect audio lead to the audio output jacks of the LCD TV.

WALL MOUNTING

Connect subwoofer to the Soundbar Caution:
If a subwoofer is to be connected, connect standard audio cable to the »SUB OUT« jack of the The ground must be firm and capable of handling the load.
Soundbar and the audio input jack of the subwoofer. Use mountings that are appropriate for the weight of the device (weight of the Soundbar T-180BT plus
Connect external device DIN safety = approx. 2.5 kg).
For wooden or hollow wall structures use suitable plugs and screws. Seek advice from a specialist dealer.

Warning: 4 Detach unit base from the Soundbar, rotate 180°.
In order to prevent injuries, the device must be securely fastened to the wall in accordance with the
installation instructions.
Note:
Installation of the Soundbar T-180BT for professional use (e.g. in a bistro) must only be carried out
by an electrically qualified person, in accordance with the applicable construction regulations as per
VDE 0100.
1 Determine place of installation and mark drill holes. 2 Drill the holes (8 mmΦ) in the wall and insert
– The distance between drill holes of the Soundbar the plugs included.
5 Place the included washer and then the snap ring onto the fixing bolt and reattach the unit base
is 64 centimetres.
through the second drill hole.
6 Affix the included spacers to the back of the unit base.
3 Screw in the two supplied screws. Distance of screw head from the wall 4 mm.

OPERATION

7 Connect a standard audio lead to the »RCA INPUT« jack of the Soundbar.
TV mode – operating with the remote control of the sound bar
– Please be aware of the left and right channels when doing so (white = left channel,red =
1 Switch Soundbar into standby mode using
right channel).
»POWER ON/OFF«.
Note:
– The LED A lights up red.
If a subwoofer is to be connected, connect standard audio cable to the »SUB OUT« jack
2 Switch Soundbar on from standby mode using » «.
of the Soundbar.
– The LED A lights up white.
8 Carefully slide the Soundbar
Note:
over the bolt heads.
After power on the source device "TV" is selected automatically.
3 Adjust the volume using »+ V« or »V –«.
4 Use » « to mute the sound.
5 Switch Soundbar into standby mode using» «.
6 Switch Soundbar off using »POWER ON/OFF«.
9 Connect audio lead to the audio output jacks of the LCD TV.
TV mode – operating with the remote control of the television
Note: If the sound is only to be played through the sound bar and the volume is to be controlled using the
If a subwoofer is to be connected, connect the audio cable to the subwoofer.
remote control of the television, this must be set in the TV. In the sound menu of your television, turn
10 Plug mains cable into the socket.
off the TV speakers, turn on the audio output, and select the status "Controllable". (This depends on
Caution:
the television; see the operating instructions of the TV.)
The Soundbar is connected to the mains via the mains cable. If you want to disconnect the
Turning on the sound bar automatically
Soundbar from the mains completely, you must pull the mains plug.
The sound bar will turn on from standby modeautomatically when there is an audio signal on the
Please ensure that the mains cable is freely accessible during operation and is not obstructed
"RCA INPUT" sockets. It turns off after about 15 minutes when the audio signal is no longer
by any other objects.
present.


Bluetooth mode

3 To ensure that the sound bar powers on, adjust the audio signal with the volume buttons on the
TV so that the power-on level is reached. Compatible with the following devices
Your device can be paired with all current, Bluetooth-enabled devices that adhere to the A2DP standard.
– The sound bar switches on.
– The LED A lights up white. This applied to smartphones, laptops and tablet PCs for example.
Search for and connect to auxiliary Bluetooth device
4 If the sound bar does not switch on, increase the volume using the volume buttons on the TV.
1 Switch Soundbar into standby mode using »POWER ON/OFF«.
Notes:
– The LED A lights up red.
The volume can be set with the remote control of the television.
2 Switch Soundbar on from standby mode using » «.
If the output signal of the TV (and thus the volume) is set too low, the sound bar may not switch on
after the TV is powered off and back on. If this is the case, increase the output signal of the TV with 3 Select "Bluetooth" source device by pressing » « on the remote control.
4 Activate the Bluetooth function on the auxiliary Bluetooth device.
the remote control of the television and use the »+ V« or »V –« buttons of the remote control of the
sound bar to adjust the volume to the desired volume. 5 Press and hold » « on the remote control of the T-180BT.
– The LED B flashes rapidly.
Caution:
If the sound bar was switched to standby with the remote control (using the »8« button), automatic 6 Start the search function on the auxiliary Bluetooth device.
– After a short period of time, your T-180BT is displayed on the Bluetooth device.
power-on is disabled. The sound bar then needs to be switched on again with this button.
Turning off the sound barautomatically 7 Select the T-180BT on the Bluetooth device and connect it.
8 When the auxiliary Bluetooth device is paired with your device, the LED B of your T-180BT
If there is no audio signal on the »RCA INPUT«and »AUX IN« sockets, then the sound bar
automatically switches to standby after 15 minutes. To use the sound bar again, switch it back on. flashes slowly.
Note:
Operating with an external device
1 If an "external" device is connected to the »AUX IN« socket, select this program source with the Your T-180BT can only receive and play back the audio signal from one Bluetooth device;
up to 8 devices can nevertheless be paired.
»AUX« button of the remote control.
2 Switch to TV mode using the »TV« button of the remote control.

Activate a paired auxiliary Bluetooth device Please note that the data transfer range can be up to 9 m, depending on the auxiliary Bluetooth device
Notes: and the structural conditions.
Auxiliary Bluetooth devices must only be paired once (depending on the auxiliary Bluetooth device).

Technical Information

When leaving and then returning to the reception range of the T-180BT, the auxiliary Bluetooth This device is suppressed in accordance with the applicable EC Directives.
device will pair with it automatically. This product conforms to European Directives 1999/5/EC, 2009/125/ EC and 2011/65/EU.
The T-18BT will only connect automatically with the last paired auxiliary Bluetooth device. The type label can be found on the back of the device.
If the auxiliary Bluetooth device is not detected,it must be reactivated via its menu. CE declaration of conformity
Playback of auxiliary Bluetooth device The CE declaration of conformity for the device can be found as a PDF file on the Grundig homepage,
1 Begin playback on auxiliary Bluetooth device. www.grundig.com/download/doc.
2 Set the desired volume using »+ V –«. Power supply: 220-240V~50/60Hz 0.1A
Note: Max. power input 2SHUDWLRQ “ : 6WDQGE\ ”  :
The volume can also be adjusted from the auxiliary Bluetooth device. Power output: DIN45324, 10% THD 2 x 20 W
3 Mute the volume using » « on the remote control. Frequency response: 20Hz - 20 kHz
4 Stop playback on auxiliary Bluetooth device. S/N ratio: • G%
Notes: Dimensions and weight: Wx H x D 99 x 9.3 x 7 cm
Various functions can also be controlled using the remote control of the T-180BT: Weight approx. 2.56 kg
– Select play-pause using » «, Technical and design modifications reserved!
– Continue playback by pressing » « again;
– select previous track using » «;
– select next track using » «.
290X110MM
145X110MM
T-180BT


Switches the device on from standby mode and back off again.
Mutes the Soundbar speakers and unmutes them again.
Press briefly to select the source device "Bluetooth";
press and hold to start Bluetooth pairing.
Selects the previous track in Bluetooth mode.
Starts playback in Bluetooth mode and switches between play/pause.
Selects the next track in Bluetooth mode.





Separation: • G%