Advertisement
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: productsupport@harborfreight.com
REV 14g
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2014 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Advertisement
Summary of Contents for Portland 61714
- Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
-
Page 2: Table Of Contents
Keep cord from heat, oil, and sharp edges. extension cord plug in any way. This design is referred to as double-insulated, indicated by Page 2 For technical questions, please call 1-888-866-5797. Item 61714... -
Page 3: Safety
Be sure switch is off when plugging in. Ground Fault Circuit Interrupter (GFCI) 4. Do not Overreach - should also be implemented – Keep proper footing and balance at all times. it prevents sustained electrical shock. Item 61714 For technical questions, please call 1-888-866-5797. Page 3... -
Page 4: General Safety
Harbor Freight Tools for a replacement. factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUcTIONS. Page 4 For technical questions, please call 1-888-866-5797. Item 61714... -
Page 5: Specifications
Specifications Electrical Rating 120VAC / 60Hz / 14A Blade Speed 4,300 RPM Blade Diameter 7" Maximum Limb Capacity 1-1/2" Diameter 3190553 Item 61714 For technical questions, please call 1-888-866-5797. Page 5... -
Page 6: Setup
3. Secure in place with a Pin (63). 7. Align the holes and secure in place with two Washers and Screws. 4. Repeat steps 2 and 3 on the other end of the Axle. Page 6 For technical questions, please call 1-888-866-5797. Item 61714... - Page 7 Functions Hopper Control Panel Locking Knob Reset Button Power Switch Hopper Control Panel Base Lower Frame Figure c Item 61714 For technical questions, please call 1-888-866-5797. Page 7...
-
Page 8: Operation
This Chipper/Shredder is equipped with an overload protection system. If the unit clogs while running, the overload protection system will shut the power off. Wait at least one minute before restarting. Press the Reset Button then turn the Power Switch on. Page 8 For technical questions, please call 1-888-866-5797. Item 61714... -
Page 9: Maintenance
Blade. Screws 5. Secure in place with the screws. Repeat with the other Blade at the same time. Figure E Item 61714 For technical questions, please call 1-888-866-5797. Page 9... -
Page 10: Parts List And Diagram
Bearing Nut Frame Plate Spanner Hex Nut Wheel Cover Switch Spring Washer 2 Lower Frame Switch Frame Plate Axle Screw Washer Power Cord Bushing Cord Sheath Wheel Cord Clamp Plate Page 10 For technical questions, please call 1-888-866-5797. Item 61714... - Page 11 Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 61714 For technical questions, please call 1-888-866-5797. Page 11...
-
Page 12: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
Need help?
Do you have a question about the 61714 and is the answer not in the manual?
Questions and answers
What is the sharpening angle for the blades?
I'd like to order a hopper to replace broken shaft of my old chipper
can I order the hopper for this product (chipper/shredder 61714)?