Advertisement
Quick Links
User Manual of Serial to WiFi Converter, Model VE10W
Wiring Architecture
RS232 Wiring Diagram
Serial
Signal
VE10W
Device
Pin
Pin no's
no's
2
RX
3
3
TX
2
5
GND
5
7
RTS
8
8
CTS
7
LED
Indicators
SYS (Red)
LAN (Green)
TX (Red)
RX (Green)
When you finish the steps mentioned above and the LED indicators are as shown, the converter is
installed correctly. You can use the Software Setup CD to setup the IP Address.
To proceed with the Advance parameter setup, you can also use a web browser (IE or Netscape) to continue
the detailed settings.
Page 11 of 18
RS485 Wiring Diagram
Signal
Serial
VE10W
Device
Pin
Signal
no's
TX
D-
1
RX
D+
2
GND
CTS
RTS
: Power
When the Power is on, the LED in ON
: Network
When the LAN signal is detected, the LED will be ON.
: Data sent
When data is sent out from the network, the LED will blink.
: Data received
When data is received in the network, the LED will blink.
RS422 Wiring Diagram
Signal
Serial
VE10W
Device
Pin
Signal
no's
D-
R-
3
D+
R+
4
T-
1
T+
2
Signal
T-
T+
R-
R+
Advertisement
Related Manuals for Vernier VE10W
Summary of Contents for Vernier VE10W
- Page 1 User Manual of Serial to WiFi Converter, Model VE10W Wiring Architecture RS232 Wiring Diagram RS485 Wiring Diagram RS422 Wiring Diagram Serial Signal VE10W Signal Serial VE10W Signal Serial VE10W Signal Device Device Device Pin no’s no’s Signal no’s Signal no’s...
- Page 2 DS Tool Software Setup DS Tool uses UDP broadcast packets to query and configure converters on the network. Insert the CD. Select “DSTool_ODM_Setup” folder. Double click “DSTool_ODM_Setup.exe”. When the “Installing DSTool” screen pops up, double click the “Start” icon for installing. After installation, “Installation was completed successfully”...
- Page 3 Serial to Wi-Fi Converter Configuration Broadcast After finishing DSTool installation, launch DSTool, double click “Broadcast” button. It will detect the existence converters in the network. Select the converters you wish to add and double click “Add” button. The table will depict the converter details such as IP address, MAC Address, Device Name and Status. Device List In the Device List icon, you will find all the added converters.
- Page 4 General After listing of device IP in “Device List” item, you can click the IP as shown in the table. General information as “Model”, “IP Address”, and “MAC Address”, “Firmware Version” “Device Name / Location“ and device working status … etc appear. You can configure some parameters and modify device name and location...
- Page 5 Networking Serial to Wi-Fi converter can support both type of IP such as Static IP or DHCP/BootP IP configuration. After modifying configuration click the icon of “Apply Only” or “Apply and Save” for finishing IP configuration. Wireless You can use the wireless item for configuring Serial to Wi-Fi Converter’s Wi-Fi parameters.
- Page 6 Management In addition to DSTool, Serial to Wi-Fi Converter can also be managed by Web and Telnet consoles as well as by SNMP. The Web and Telnet functions are enabled as default. To enable or disable the management consoles, you can use the “Configuration” and “Management”...
- Page 7 Port Port Configurations is for configuring Serial parameters. Port Alias : Remarks for the port. Baud rate : From 110bps to 460.8kbps Parity : No, Even, Odd, Mark, Space Data Bits : 5, 6, 7, 8 Stop Bits: 1, 2 (1.5) Flow Control : None, XON/XOFF, RTS/CTS, DTR/DSR Interface : RS232...
- Page 8 This operation mode supports up to 5 simultaneous connections, so that multiple hosts can collect data from the same serial device at the same time. Service Mode : Virtual COM Mode This option enables the Serial Port in the Converter to act and be controlled as PC’s COM port for Windows. One PC can have as many as COM ports on the network without the limitation of PC’s physical slots.
- Page 9 Virtual COM Wizard DSTool offers one of the easiest way to add serial COM ports over the network by the Virtual COM Wizard. Serial Wi-Fi Converter COM port driver is installed when you install DSTool. Select the Virtual COM Wizard from Setup Wizard.
- Page 10 Specify the Virtual COM port range and continue the operation by checking the COM port table Serial Tunnel Wizard The Serial Tunnel Wizard gives you the option to transparently pair two devices over the network. Select the devices that should be paired and move the devices into IP1 and IP2.
- Page 11 Group IP Wizard When you have more than one device to configure, use Group IP wizard to configure all IP addresses of the devices remotely. Select Group IP Wizard after opening DSTool, or use Broadcast and find more than one Converters on the network and double click the button of “Click here”...
- Page 12 Click NEXT to confirm the setup and the IP configuration is finished, you will see the IP addresses for the devices Group Setup Wizard Group Setup Wizard can help you to copy the configuration of one device to other converters. You can select the items to be copied.
- Page 13 Select the Source device for the configuration and Destination devices. Click NEXT to confirm and finish the wizard. Page 1313 of...
- Page 14 Group Firmware Wizard To update firmware for a group of devices can be as easy as 4 steps of Group Firmware Wizard Select the device model as Serial to Wi-Fi Converter DS-11- W, and select available converters on the network for the upgrade Specify the firmware image and select NEXT.
- Page 15 IP Collection Dynamic DHCP IP settings find the changing IP addresses. DSTool supports auto IP reporting function to report the current IP address of the Serial to Wi-Fi converter units to administrator. To enable the function, check “Auto IP Report” in “Configuration”, “General”.
- Page 16 Web Console Configuration Here you can verify the connections & settings. Connect a PC to the Converter. The operating system can be Windows 95, 98, ME, XP, 2000. The “Hyper Terminal” utility should be installed on your PC (see Figure 4.1). Connect the RS232 port of the Converter to the PC COM port &...
- Page 17 After “OK” button is pressed, Figure 4.5 appears. If the Hyper Terminal connects with the converter successfully, the time clock at the “left lower” corner “Connected hh:mm:ss” will start counting. Figure 4.5 Hyper Terminal for COM Port Initiate another Hyper Terminal as a COM Port Terminal (in Figure 4.3, select COM 1 or other COM port instead of “TCP/IP (Winsock)”).
- Page 18 Pin outs RS-232 Pin Assignment The pin assignment scheme for a 9-pin male connector on a DTE is given below. PIN 1 : DCD PIN 2 : RXD PIN 3 : TXD PIN 4 : DTR PIN 5 : GND PIN 6 : DSR PIN 7 : RTS PIN 8 : CTS PIN 9 : DC 5V...