Clicker K3 User Manual

CLICKER MODEL K3
Wireless Keypad - For use with Garage Door Openers
The Clicker can be
programmed to operate with
different brands of garage
door openers.
Compatible with most garage
door opener systems
manufactured by Chamberlain,
Genie, LiftMaster, Linear,
Master Mechanic, Moore-O-
Matic, Multi-Code, Sears,
Stanley, and Do It.
THE CLICKER IS NOT COMPATIBLE WITH ROTATING CODE SYSTEMS SUCH AS
GENIE INTELLICODE, STANLEY SECURE CODE OR SECURITY✚ GARAGE DOOR
OPENER SYSTEMS DEVELOPED BY SEVERAL MANUFACTURERS SINCE 1996.
Identify Your Garage Door Opener Brand
Determine your brand from an original hand held remote or locate the motor unit
receiver. The receiver can be mounted on the back or side panel of the motor unit
or could be mounted on the ceiling or wall.
SECTION BRAND
1 Linear, Moore-O-Matic
2 Stanley
3 Multi-Code
4 Chamberlain, LiftMaster,
Master Mechanic, Sears, Do It
5 Genie (9 Code Switch Systems)
6 Genie (12 Code Switch Systems)
Helpful Hints
You must choose a 3-digit Personal Identification Number (PIN) when
programming the K3. After programming is complete, your PIN plus any
additional number must be entered to activate your system.
If an incorrect PIN is entered, it is necessary to wait 30 seconds before proceeding.
Once programmed, the K3 will activate your garage door opener. The keypad
remains active for 30 seconds. During this time you may stop, reverse or
reactivate the door by pressing any number on the keypad.
MOUNTING THE K3
Select a smooth vertical surface. Mount the keypad out of the path of the moving
garage door, but within sight of it. At least 4 inches of clearance is needed above
the keypad in order to slide the cover up.
Slide outside cover up and remove. Remove battery cover. Take battery out of
compartment (it is not necessary to disconnect it). Mount the keypad using the
screws supplied, then reinsert battery, replace battery cover, and slide outside
cover down.
BATTERY REPLACEMENT
Replace the 9-volt battery when the keypad light becomes dim or does not light
up. Slide the outside cover up, unscrew the battery cover and replace battery. It
may be necessary to reprogram the keypad after battery is replaced.
NOTICE: To comply with FCC and or Industry Canada rules, adjustment or modifications of this receiver
and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE
NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep keypads out of reach of children. NEVER permit children to
CAUTION
operate, or play with remote control transmitters/keypads.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted,
and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. Never
permit anyone to cross path of moving gate or door.
Motor Unit
And Receiver
1 2 3
4 5 6
7 8 9
0 #
Circle your
Brand and
proceed to the
appropriate
section.
CHANGING YOUR PIN
It is not necessary to reprogram the K3 to change the existing PIN.
To change your PIN:
I Enter existing 3-digit PIN and the * key.
I Enter new 3-digit PIN and the * key.
I WAIT 30 SECONDS - To test, enter new 3-digit PIN followed by any 4th
additional number. Note: Do not use the * or # keys as number.
1 LINEAR AND MOORE-O-MATIC
Locate your systems code switch positions from an original hand held remote or
the motor unit receiver. If the switch is "on" or "up", place a 1; "off" or
"down", place a 2 in the corresponding box in the TABLE below.
1 2 3 4 5 6 7 8
CODE SWITCH SEQUENCE
ON/UP
OFF/DOWN
Choose a 3-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
Write PIN here:
Step 1 Enter 1 2 3 and the * key.
Step 2 Enter your PIN and the * key.
Step 3 WAIT 30 SECONDS
Step 4 Enter your PIN and the # key.
Step 5 Enter 1 and the # key.
Step 6 Enter code in sequence from the TABLE above and the # key.
Step 7 WAIT 30 SECONDS - Programming is complete.
To test enter PIN followed by any 4th additional number.
Note: Do not use the * star or # pound keys as a 4th number.
If programming is unsuccessful, wait 30 seconds before attempting to
reprogram. Reverse code from TABLE above (Change 1 to 2; 2 to 1)
To clear and start over: Press the * star and # pound keys simultaneously.
Release after keypad begins to flash rapidly. This will set the keypad back to the
factory setting. Repeat programming procedures.
To program a second door, return to Step 1, choose a different PIN, and enter 4
5 6 instead of 1 2 3. Proceed with steps 2 through 7. If unsuccessful, clearing
the keypad back to the factory setting will erase the first door programmed.
2 STANLEY • 3 MULTI-CODE
Locate your systems code switch positions from an original hand held remote or
the motor unit receiver. If the switch is "on" or "up", place a 1; "off" or "down",
place a 2 in the corresponding box in the TABLE below.
CODE SWITCH SEQUENCE
1 2 3 4 5 6 7 8 9 10
ON/UP
OFF/DOWN
Choose a 3-digit Personal Identification Number (PIN). Any combination of
numbers from 0 to 9 may be used.
Write PIN here:
Step 1 Enter 1 2 3 and the * key.
Step 2 Enter your PIN and the * key.
Step 3 WAIT 30 SECONDS
Step 4 Enter your PIN and the # key.
Step 5 STANLEY - Enter 2 and the # key.
MULTI-CODE - Enter 3 and the # key.
Step 6 Enter code in sequence from the TABLE above and the # key.
Step 7 WAIT 30 SECONDS - Programming is complete.
To test enter PIN followed by any 4th additional number.
Note: Do not use the * star or # pound keys as a 4th number.
If programming is unsuccessful, wait 30 seconds before attempting to reprogram.
Reverse code from TABLE above (Change 1 to 2; 2 to 1) Stanley brands * try as
Multi-Code, Multi-Code brands * try as Stanley.
To clear and start over: Press the * star and # pound keys simultaneously.
Release after keypad begins to flash rapidly. This will set the keypad back to the
factory setting. Repeat programming procedures.
To program a second door, return to Step 1, choose a different PIN, and enter 4 5
6 instead of 1 2 3. Proceed with steps 2 through 7. If unsuccessful, clearing the
keypad back to the factory setting will erase the first door programmed.
PROGRAMMING
PROGRAMMING
WARNING
WARNING