Noise Information; Mounting Vac Accessories; Assembly; Inserting A Disposal Bbag - Bosch GAS 35 M AFC Professional Original Instructions Manual

OBJ_BUCH-1715-001.book Page 19 Thursday, February 14, 2013 4:04 PM
Automatic Start/Stop feature*
max. power
Rated voltage
EU 220 –240 V
UK 110 V
UK/DK 240/230 V
CH 230 V
* Specification of the allowable load of the connected power tool (coun-
try-specific)

Noise Information

Measured sound values determined according to EN 60704.
Typically the A-weighted sound pressure level of the vacuum
cleaner is lower than 70 dB(A). Uncertainty K= 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
and the directives 2011/65/EU, 2006/42/EC,
2004/108/EC including their amendments.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Helmut Heinzelmann
Senior Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
15.02.2013

Assembly

 Before any work on the vacuum cleaner itself, pull the
mains plug.
Mounting the Vacuum-hose Holder (see figure A)
– Slide the vacuum-hose holders 4 firmly from above into the
retainers 32 intended for this purpose, until they engage.
Mounting the Vacuum Hose (see figure B)
– Mount the vacuum hose 24 onto the hose connection
piece 3 and turn it in clockwise direction to the stop.
Note: While vacuuming, an electrostatic charge develops in
the vacuum hose and accessories caused through the friction
of the dust, which the operator could experience in the form
of static discharging (dependent on environmental influences
and physical perception).
As a general rule, Bosch recommends using an anti-static vac-
uum hose (accessory), when vacuuming fine dusts and dry
materials.
Bosch Power Tools
Mounting VAC Accessories (see figure C)
The vacuum hose 24 is equipped with a clip system, with
min. power
which the VAC accessories (tool sleeve 22, elbow 23) can be
output output
connected.
2200 W 100 W
Mounting the Tool Sleeve
750 W 100 W
– Mount the tool sleeve 22 onto the vacuum hose 24 until
1800 W 100 W
both snap-fasteners 33 of the vacuum hose can be heard
1100 W 100 W
to engage.
– To disassemble, press both snap-fasteners 33 inward and
pull the components apart.
Mounting Nozzles and Tubes
– Mount the elbow 23 onto the vacuum hose 24 until both snap-
fasteners 33 of the vacuum hose can be heard to engage.
– Afterwards, mount the desired VAC accessory (floor noz-
zle, crevice nozzle, vacuum tube, etc.) firmly onto the el-
bow 23.
– To disassemble, press both snap-fasteners 33 inward and
pull the components apart.
Inserting/Removing a Disposal Bag or Dust Bag
(Dry Vacuuming) (see figures D1
For dry vacuuming of materials according to dust category M,
a disposal bag 25 or a dust bag must be inserted.
When vacuuming materials with or without an exposition limit
value ≥ 1 mg/m
to vacuum directly into the container.
Note: When using a paper filter bag, the automatic filter
cleaning (AFC) (see "Deactivating the AFC", page 21) must,
and when using a fleece filter bag, should be shut off.
Have the emptying and maintenance, incl. the disposal of
dust-collection containers, carried out only by specialists.
Appropriate protective equipment is required. Do not op-
erate the vacuum cleaner without the complete filter sys-
tem. Otherwise there is danger to your own health.

Inserting a Disposal bBag

– Unlock the latches 13 and remove the vacuum lid 12.
– Insert the disposal bag 25 into the container 1 with the fill-
ing opening toward the front.
– Pull the filling opening over the connection flange into the
recess of the connection flange.
– Make sure that the disposal bag 25 faces completely
against the interior sides of the container 1.
– Fold the rest of the disposal bag 25 over the edge of the
container 1.
– Reattach the vacuum lid 12 again and lock the latches 13.
Removing and Closing the Disposal Bag
– Unlock the latches 13 and remove the vacuum lid 12.
– Pull the full disposal bag 25 toward the rear off of the con-
nection flange.
– Carefully remove the disposal bag 25 out of the vacuum
cleaner without damaging it.
When doing this, pay attention that the disposal bag does
not get caught or ripped open against the connection
flange or other sharp objects.
3
(according to dust category L), it is possible
The vacuum cleaner contains materials
WARNING
that are hazardous to one's health.
English | 19
D2)
–
1 619 929 L61 | (14.2.13)