Fluke 6055 Manuals

Manuals and User Guides for Fluke 6055. We have 1 Fluke 6055 manual available for free PDF download: User Manual

Fluke 6055 User Manual

Fluke 6055 User Manual (63 pages)

Calibration Bath

Brand: Fluke | Category: Test Equipment | Size: 1.47 MB

Table of Contents

Table of Contents
3
1 Before You Start

7
- Symbols Used
  7
- Safety Information
  8
  - Warnings
    8
  - Cautions
    11
- Authorized Service Centers
  12
2 Introduction

14
3 Specifications and Environmental Conditions

15
- Specifications
  15
- Environmental Conditions
  15
4 Installation

17
- Unpacking
  17
- Comments Concerning the Use of Salt
  18
- Bath Environment
  18
- Dry-Out" Period
  18
- Power
  18
- Setup
  18
- Setting the Temperature
  19
5 Bath Use

21
- General
  21
- Comparison Calibration
  21
- Calibration of Multiple Probes
  22
6 Parts and Controls

25
- Power Panel
  25
- Figure 3 Back Panel
  25
- Back Panel
  26
7 General Operation

27
- Two Modes of Temperature Control
  27
  - Temperature Control Mode
    27
  - Temperature Drift Mode
    27
  - Figure 4 System Diagram
    28
- Bath Fluid
  29
- Fluid System
  29
- Fluid Drain
  29
- Filling the Bath
  29
  - Using Heat Transfer Salt
    29
    
    The First Salt Load
    29
    
    Figure 5 System Diagram
    30
    
    Melting the Salt
    31
- Stirring
  32
- Power
  32
8 Controller Operation

33
- Bath Temperature
  33
- Reset Cut-Out
  33
- Figure 6 Controller Operation Flowchart
  34
- Temperature Set-Point
  35
  - Programmable Set-Points
    35
  - Set-Point Value
    36
  - Set-Point Vernier
    36
- Temperature Scale Units
  37
- Secondary Menu
  38
- Heater Power
  38
- Proportional Band
  38
- Figure 7 Bath Temperature Fluctuations at Various Proportional Band Settings
  39
- Cut-Out
  40
- Controller Configuration
  41
- Probe Parameters
  41
  - Alpha
    42
- Operating Parameters
  42
  - Cut-Out Reset Mode
    42
  - Stir Mode Select
    42
  - Stir Set-Point
    43
  - Heat up Power
    43
- Serial Interface Parameters
  44
  - Baud Rate
    44
  - Sample Period
    45
  - Duplex Mode
    45
  - Linefeed
    45
- IEEE-488 Parameters
  46
  - IEEE-488 Address
    46
- Calibration Parameters
  46
  - Cto
    47
  - CO and CG
    47
  - H and L
    47
9 Digital Communication Interface

48
- Serial Communications
  48
  - Wiring
    48
  - Setup
    48
    
    Figure 8 Serial Cable Wiring Diagram
    48
    
    Baud Rate
    49
    
    Duplex Mode
    49
    
    Linefeed
    49
    
    Sample Period
    49
  - Serial Operation
    49
- IEEE-488 Communication (Optional)
  50
  - Setup and Address Selection
    50
  - IEEE-488 Operation
    50
- Interface Commands
  50
- Power Commands
  54
- Heater Settings for Control
  55
- Power Commands
  55
10 Calibration Procedure

56
- Calibration Points
  56
- Measuring the Set-Point Error
  56
- Computing R0 and ALPHA
  56
- Calibration Example
  57
- Figure 9 Calibration Example
  58
11 Maintenance

59
12 Troubleshooting

61
- Comments
  63
  - EMC Directive
    63
  - Low Voltage Directive (Safety)
    63

Advertisement

Advertisement

Related Products

Fluke Categories

Measuring Instruments Test Equipment Multimeter Thermometer Laboratory Equipment

More Fluke Manuals