Operating the machine outside of any of the above limitations is considered abuse and any resulting Scotsman reserves the right to make design changes damage is not covered by warranty and could cause a and/or improvements at any time. Specifications and complete loss of warranty coverage.
HID312, HID525 and HID540 Installation and User’s Manual Placement The location of the equipment should be selected Cafeteria applications. with care. Consideration should be given to allow The unit can be placed in a cafeteria line for ice and adequate space on the sides for air cooled models to water.
HID312, HID525 and HID540 Installation and User’s Manual Counter Installations Panel Removal Units placed on a counter must either use legs or be sealed to the counter top with food grade sealant per Remove one screw at bottom front of upper front local codes.
HID312, HID525 and HID540 Installation and User’s Manual Machine Stands Scotsman manufactures two machines stands for the HID dispensers: a 16 inch wide model and a 21 inch wide model. The prior machine stands are not suitable for use with the HID models and their use is not recommended.
HID312, HID525 and HID540 Installation and User’s Manual Component Location Photo-Electric Eye Ice Ice Making Level Sensors System Water Reservoir Agitator, Dispense Bar, Dispense Compressor Rotor Control Box Electronic Condenser Controller Compressor Ice Dispense Sensor Drain Basin and Manifold Water Dispense...
To locate one, call the number on machine will act as an internal vent, no additional the back of this manual or go to Scotsman’s website vent should be required unless there is a very long www.scotsman-ice.com to identify a local distributor or horizontal run.
Make sure they know who to call for service. 14. Fill out the Customer Evaluation and Warranty Registration form, and mail it in to Scotsman or ON / OFF register the unit at Scotsman’s website (www.
HID312, HID525 and HID540 Installation and User’s Manual Operation: Ice and Water Vending During ice making soft ice is compressed thru a die Other notes: and then broken off into irregular lengths. It will not be • An occasional drip may be seen from the ice clear and, because of melting, when dispensed it will dispense chute.
HID312, HID525 and HID540 Installation and User’s Manual Controller All models use the same control system. The electronic controller operates the compressor (with fan motor), auger drive motor, dispense drive motor and inlet water solenoid valve. It monitors: • Reservoir water availability •...
HID312, HID525 and HID540 Installation and User’s Manual Maintenance and Cleaning There are five areas of maintenance: 4. Remove screws holding lower front panel to unit and unplug lower panel sensors at the harness 1. Drip tray and drain system connection.
HID312, HID525 and HID540 Installation and User’s Manual Air filter The air filter on the left side of the cabinet will capture significant dust and lint during operation. As the dirt builds up it begins to restrict air flow and causes the refrigeration system to work longer to make ice.
5. Disconnect ice level control at harness. 11. Mix a solution of ice machine scale remover, such Moving parts hazard. as Scotsman Clear 1 and potable water per the Risk of personal injury. directions supplied with the scale remover. Disconnect electrical 12.
HID312, HID525 and HID540 Installation and User’s Manual Ice level controls Clean if the controller indicates bin full and there 5. Remove the chute is no ice between the sensors. mounting panel. 1. Remove top front and top panels. 2. Shut machine off.
Call drained. Physician immediately. In case of external contact, flush 6. Mix a solution of 12 ounces of Scotsman Clear with water. 1 ice machine scale remover and 12 ounces of KEEP OUT OF THE REACH clean, potable water.
Page 20
HID312, HID525 and HID540 Installation and User’s Manual 14. Push the Clean button. The unit will operate the 28. Return the ice discharge chute, water reservoir auger motor for 30 minutes and then stop. cover, and ice dispense chute to their original positions and secure them with their original Note: Stop at any time by pushing the On/Off button.
HID312, HID525 and HID540 Installation and User’s Manual Basic Troubleshooting See the separate HID service manual for more advanced troubleshooting information. Symptom Possible Cause Probable Correction No ice is dispensed No ice in bin Unit in Off mode. Remove upper front panel and check controller code, push On/Off button to restart.
HID312, HID525 and HID540 Installation and User’s Manual Controller Diagnostics Code or Light Action Probable Cause Suggested Action Unit manually switched off If desired, switch unit on. Freeze mode None, unit is making ice. Bin sensors sense bin full Check if bin is full.