Deionized water will not work and isn’t recommended. approved by Scotsman. Voltage Scotsman reserves the right to make design changes • Maximum: 126 Minimum: 104 and/or improvements at any time. Specifications and design are subject to change without notice.
HID312AW, HID525AW and HID540AW Installation and User’s Manual Placement The location of the equipment should be selected Remove bolts holding machine to pallet. Use caution with care. Consideration should be given to allow to not tip unit too far when removing bolts.
To locate one, call the number on fitting at the back of the cabinet. Use 3/4 inch rigid the back of this manual or go to Scotsman’s website tubing, use material to meet local codes. The drain www.scotsman-ice.com to identify a local distributor or basin in the machine will act as an internal vent, no service company.
HID312AW, HID525AW and HID540AW Installation and User’s Manual Wall Mounting It is recommended that the wall mounting installation 6. Use a mechanical hoist to lift the cabinet high be done by an experienced contractor. enough to fit the flange of the machine bracket over the lip of the wall bracket.
Make sure they know who to call for service. 14. Fill out the Customer Evaluation and Warranty Registration form, and mail it in to Scotsman or register the unit at Scotsman’s website (www. scotsman-ice.com). 1. Remove upper front panel 2.
HID312AW, HID525AW and HID540AW Installation and User’s Manual Operation: Ice and Water Vending Dispensing takes place when the Touch Free sensor’s container. infrared beam bounces back to the sensor from a • Both dispensing and ice making are disabled container placed directly in front of it.
HID312AW, HID525AW and HID540AW Installation and User’s Manual Controller All models use the same control system. There is also a code display, the codes are: - - - for off The electronic controller operates the compressor (with fan motor), auger drive motor, dispense drive - - - for ice making motor and inlet water solenoid valve.
HID312AW, HID525AW and HID540AW Installation and User’s Manual Maintenance and Cleaning There are five areas of maintenance: Condenser. 1. Drain system The condenser fins may need cleaning too. Remove the left side air grill and brush any lint and dirt off the 2.
11. Mix a solution of ice machine scale remover, such sanitized on a regular basis, at a minimum when the as Scotsman Clear 1 and potable water per the ice making system is cleaned. Hand tools and hand directions supplied with the scale remover.
HID312AW, HID525AW and HID540AW Installation and User’s Manual Ice level controls, Clean if the controller indicates bin full and there is no ice between the sensors. 1. Remove top front and top panels. 2. Shut machine off. 6. Remove the chute 3.
OF CHILDREN and return it to 6. Mix a solution of 12 ounces of Scotsman Clear the plug when drained. 1 ice machine scale remover and 12 ounces of 19. Mix a solution of 4 ounces of ice machine scale clean, potable water.
Page 17
HID312AW, HID525AW and HID540AW Installation and User’s Manual Sanitize now. 33. Return the ice dispense chute and water reservoir cover to their original positions and secure them 20. Mix a 2 gallon solution of sanitizer. A with their original fasteners.
HID312AW, HID525AW and HID540AW Installation and User’s Manual Basic Troubleshooting See the separate HID service manual for more advanced troubleshooting information. Symptom Possible Cause Probable Correction No ice is dispensed No ice in bin Unit in Off mode. Remove upper front panel and check controller code, push On/Off button to restart.
HID312AW, HID525AW and HID540AW Installation and User’s Manual Controller Diagnostics Code or Light Action Probable Cause Suggested Action Unit manually switched off If desired, switch unit on. Freeze mode None, unit is making ice. Bin sensors sense bin full Check if bin is full.
Page 20
SCOTSMAN ICE SYSTEMS 101 Corporate Woods Parkway Vernon Hills, IL 60061 800-726-8762 17-3492-03 Rev. A...