AOpen DE896-FL Assembly Manual
  1. Manuals
  2. Brands
  3. AOpen Manuals
  4. Desktop
  5. DE896-FL
  6. Assembly manual
AOpen DE896-FL Assembly Manual

AOpen DE896-FL Assembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Assembly Guide for DE896-FL
V1.0
2007/10/28

Advertisement

Table of Contents
loading

Related Manuals for AOpen DE896-FL

Summary of Contents for AOpen DE896-FL

  • Page 1 Assembly Guide for DE896-FL V1.0 2007/10/28...

  • Page 3: Table Of Contents

    Index 1. Outlook …………..……………………………………………2 2. Open Housing ……………………………………...………...4 3. Install Key components ………………………………………7 4. Assemble the Supporter & Upper Case…………………..10 5. Appendix 1 Packing List…………………………………….15 6. Appendix 2 Table of Screw and TOQUE………………….16 7. Appendix 3 Watch Dog Timer Configuration…….………..17 8.

  • Page 4: Outlook

    1. Outlook Front IO Front USB Front USB Power Button Power Button...
  • Page 5 Rear IO Kingstone Kingstone Antenna Antenna Audio Audio Lock Lock Hole Hole Port Port DC Power DC Power PS/2 PS/2 (with Y cable can support PS/2 KB & MS) (with Y cable can support PS/2 KB & MS)

  • Page 6: Open Housing

    2. Open Housing 2-1 . Unscrew the upper case (2pcs of FPH M3 screws in rear side) (Screwdriver torque : 5.0±0.2 kgf. cm ) 2-2. Unscrew the upper case (2pcs of FH M3 screws in top side ). (Screwdriver torque : 5.0±0.2 kgf. cm )
  • Page 7 2-3. Remove the Upper case 2-4. Unscrew 3 screws from HDD supporter (Screwdriver torque : 5.0±0.2 kgf. cm ) Front side Rear side 2-5. Remove the protection from HDD supporter’s thermal tape...
  • Page 8 2-6. You will see the kernel of Digital Engine VIA C7 series CPU is nano BGA package, so the CPU already mount on MB No need to detach the CPU Heatsink.

  • Page 9: Install Key Components

    3. Install Key components 3-1 Insert memory module Insert the memory module in upper slot in 30 degree angle as shown in the picture, push down the memory module slowly till there's a clipping sound.
  • Page 10 3-2 . Assemble the hard disc 3-2-1. Insert the SATA hard disc into the support with about 30 degree angle 3-2-2. Screw the hard disc on the supporter with 4pcs of FPH M3 screws (Screwdriver torque : 2.5±0.1 kgf. cm )
  • Page 11 3-3. Assemble the MPI-SATA card 3-3-1. Assemble the MPI-SATA card to the 3-3-2. Screw the MPI-SATA card on the hard disc supporter with 2pcs M2 screws (Screwdriver torque:0.7±0.1kgf.cm) 3-3-3. FPH M3 Screw FPH M2xL3 Screw FH M3 Screw...

  • Page 12: Assemble The Supporter & Upper Case

    4. Assemble the Supporter & Upper Case 4-1. Assemble the supporter and lower case 4-1-1 Insert the MPI-SATA card into the slot on 4-1-2Screw the supporter on the lower motherboard case with 2pcs of FH M3 screws and 1pcs of FPH M3 screw (Screwdriver torque : 5.0±0.2 kgf.
  • Page 13 4-2. Connect the wires 4-2-1.Connect the power switch wire 4-2-2.Connect the front USB wires 4-2-3 Adjust the USB cable to arrange it under the supporter...
  • Page 14 4-3. Assemble the upper case 4-3-1 Slide in the uppercase carefully. 4-3-2 Check if the upper case is rigidly combined with lower case 4-3-3.Screw the upper case (2pcs of FPH M3 3-4-4 Screw the top case (2pcs of FH M3 screws in rear side ).
  • Page 15 4-4. Assemble miniPCI Wireless LAN or TV Tuner card 4-4-1 cable and nut 4-4-2 Note the hole shape to adjust the A,B inside housing; C,D outside housing antenna SMA connector to insert into the hole. 4-4-3. Insert a washer to one end of the antenna 4-4-4 se the screwdriver or the long nos wire .
  • Page 16 4-4-5. Align the notch and Insert the card into 4-4-6. Install the antenna wire with the button the slot and make sure it be locked on the of the wireless LAN or TV-tuner card salient of the slot . Fool-Proof notch Fool-Proof notch 4-4-7.

  • Page 17: Appendix 1 Packing List

    Appendix 1 Packing List 1 x DE896-FL system 1 x MPI-SATA card 1 x Easy Assembly Guide 1 x Driver CD 1 x 65W Adapter and Power Cord 1 x L type Holder for fanless model with 4 pcs of M3 screw...

  • Page 18: Appendix 2 Table Of Screw And Toque

    Appendix 2 Table of Screw and Torque Screw Photo Position Q’ty Screw spec. Torque Screw driver spec. ⊕ Rear side FPH M3- L5 5±0. 2 Phillips #2 kgf-cm ⊕ FPH M3- L5 2.5±0. 2 Phill ips #2 ≧ 8cm Length kgf-cm ⊕...

  • Page 19: Appendix 3 Watch Dog Timer Configuration

    Appendix 3 Watch Dog Timer Configuration WDT is used to g enerate a variet utput signals after a use programmable count. The WDT is suitable for use in the prevention stem lock-up, such as when software becomes trapped in a deadlock. nder these sort of circumstances, the timer will count to zero and the lected outputs will be driven.
  • Page 20 CODE FLOW-CHART 1. Initial Watchdog Pin (1)set -> Logical Device: Global CR: 0x2D Bit: 0 = 0 WDTO. (2)set -> Logical Device: 0x09 CR: 0X30 Sta t r Bit:3 = 1 activate GPIO5 CR: 0xE0, 0xE1, 0xE2 Bit: 6, Bit: 7, Bit: 6 = 0 GPIO port is programmed as an output port.
  • Page 21 1. Set Mode (1)set -> Logical Device: 0x08 CR: 0xF5 Set Min/Sec Mode Bit: 3 = 0 By second = 1 By minute Star imer 1. Set Mode (1)set -> Logi cal Device: 0x08 CR: 0xF6 Bit: 7~0 = 0x01 Time- out occur after 1 second/minute = 0xFF Time- out occur after 255 second/minute...

  • Page 22: Sample Code

    SAMPLE CODE: his code and information is provided "as is" without warr anty of any kind, either expressed or mplied, includin but not limited to the implie d warranties of merchantab ility and/or fitness for a articular purpose. This program just for MB with Winbond W83267 DHG LPC I/O .
  • Page 23 2. Stop Timer 3. Set Min/Sec Mode outportb(0x2E,0x87); outportb(0x2E,0x87); outportb(0x2E,0x87); outportb(0x2E,0x87); outportb(0x2E,0x87); outportb(0x2E,0x87); outportb(0x2E,0x07); outportb(0x2E,0x07); outportb(0x2E,0x07); outportb(0x2F,0x08); outportb(0x2F,0x08); outportb(0x2F,0x08); outportb(0x2E,0xF5); outportb(0x2E,0xF6); outportb(0x2E,0xF7); outportb(0x2F,byBit); outportb(0x2F,byBit); outportb(0x2F,byBit); outportb(0x2E,0xAA); outportb(0x2E,0xAA); outportb(0x2E,0xAA); 4. Start Timer outportb(0x2E,0x87); outportb(0x2E,0x87); outportb(0x2E,0x87); outportb(0x2E,0x87); outportb(0x2E,0x07); outportb(0x2E,0x07) outportb(0x2F ,0x08); outportb(0x2F,0x08); outportb(0x2E,0x30);...

  • Page 24: Appendix 4 Outline And Holder Drawing

    Appendix 4 Outline and Holder Drawing A. Dimension of DE-945FL (unit: mm)
  • Page 25 B. L type Holder (Include 2 piece of holder and 4pcs of M3 screws) Dimension of L type Holder (unit: mm)
  • Page 26 C. Vertical Holder --- optional (Include 2 piece of holder and 8@M3 screws) C-1. Dimension of Vertical Holder (Single Stand) (unit: mm)
  • Page 27 C-2. Dimension of Vertical Holder (Double Stand) (unit: mm)
  • Page 28 P/N: 49.ADE01.0310（L） S/N : 077-112-228...

Table of Contents