Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CompuLab SBC-A510
Summary of Contents for CompuLab SBC-A510
- Page 1 SB-A510 Reference Guide...
- Page 2 To the extent permitted by law no liability (including liability to any person by reason of negligence) will be accepted by CompuLab, its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
-
Page 3: Table Of Contents
Power Output Terminals (P17, P19) ................. 20 4.12 S-ATA Connector (P18) .................... 20 4.13 S/PDIF Connectors (P22, U6) ................... 21 4.14 CompuLab Video Input FPC (P25) ................22 4.15 MMC/SD/SDIO Socket (P5) ..................23 4.16 Audio Jacks (J1, J3) ....................23 4.17 MISC. - Page 4 Table of Contents MECHANICAL DRAWINGS ..................27 OPERATIONAL CHARACTERISTICS ............... 29 Absolute Maximum Ratings ..................29 Recommended Operating Conditions ................29 DC Electrical Characteristics ..................29 Power Consumption ....................... 29 Operating Temperature Ranges..................30 ACCESSORIES ........................ 31 Revised May 2011 SB-A510 Rev 1.1...
- Page 5 May 2011 Fixed table 4, Jumper E8 description fixed. Please check for a newer revision of this manual at CompuLab's web site – http://www.compulab.co.il/ Compare the revision notes of the updated manual from the web site to those of the printed or electronic version you have.
-
Page 6: Introduction
About This Document This document is part of a set of reference documents providing information necessary to operate and program CompuLab’s SBC-A510. Related Documents For additional information not covered in this manual, please refer to the documents listed in Table 2. -
Page 7: Overview
OVERVIEW Highlights Single board computer implemented The SBC-A510 is a micro-ATX compliant, by the combination of a CM-A510 single board computer. It is implemented module and a SB-A510 baseboard. with a CM-A510 module providing most of Micro-ATX form factor. -
Page 8: Block Diagram
Block Diagram Figure 1 SB-A510 Block Diagram b a c k-u p S te re o o u t c o in c e ll b a tte ry R T C a u d io ja c k A u d io V m e ta C o d e c S te re o in... -
Page 9: Features
Features SB-A510 does not have assembly options. The "CM Option" column specifies the P/N code of CM- A510 required to have the particular feature. "+" means that the feature is always available, regardless of P/N code. Table 3 SB-A510 Features CM-A510 Feature Specifications... - Page 10 Interfaces and Connectors Table 4 Electrical, Mechanical and Environmental Specifications High efficiency switched power supply. Supply Voltage Unregulated 7.5 to 17 volt input Power consumption 3W to 8W in full activity, depending on CPU speed and selected features Dimensions 170 mm (L) x 170 mm (W) x 35 mm (H) Weight 200 gram Commercial: 0o to 70o C...
-
Page 11: System Components
Interfaces and Connectors SYSTEM COMPONENTS DC Power Supply All SB-A510 power rails are generated from a 12V DC input (connector J2). SB-A510 supports two power states: Full power mode – all SB-A510 power rails are enabled. Low power mode – only power rails required for sleep-mode support are enabled. All other voltage rails are disabled (gated). -
Page 12: Dvi Transmitter
Interfaces and Connectors DVI Transmitter The SB-A510 is equipped with a DVI Transmitter that is based on the TFP410/SIL164 IC. DVI output signals are routed to the onboard HDMI Connector (J4). The DVI Transmitter is connected to the 24bit RGB interface of the CM-A510. TFP410/SIL164 is fully DVI 1.0 compliant. -
Page 13: Back-Up Battery
Interfaces and Connectors Back-Up Battery SB-A510 is supplied with a 3V 200mAh Lithium Dioxide coin cell, which powers the CM-A510 RTC whenever the main power supply is not present. 4 .22 NOTE: The E5 jumper must be installed for RTC back-up support. Please refer to chapter for additional details. -
Page 14: Interfaces And Connectors
Signal Name Signal Name RS232_TXD RS232_RTS RS232_RXD RS232_CTS Table 10 P10 connector data Manufacturer Mfg. P/N Mating connector Wieson G3169-500001 Wieson, P/N: 4306-5000 The connector is compatible with the CABDB9UMP cable supplied by CompuLab. Revised May 2011 SB-A510 Rev 1.1... -
Page 15: Usb Host Connectors (P11, P15)
Interfaces and Connectors USB Host Connectors (P11, P15) The four USB2.0 host ports provided by the CM-A510 are available through two dual type-A USB connectors (P11 & P15). For USB ports 1, 2 and 3, the CM-A510 provides the “VBUS enable” signal and monitors the “VBUS good”... -
Page 16: Analog Vga Connector (P7)
Interfaces and Connectors Table 15 P15 connector pinout (Ethernet) Signal Name Signal Name LAN1_CT1 LAN1_CT2 LAN1_MDIP0 VCC3_3 LAN1_MDIN0 LAN1_ACT_T LAN1_MDIP1 LAN1_LINK LAN1_MDIN1 VCC3_3 LAN1_MDIP2 LAN1_MDIN2 LAN1_MDIP3 LAN1_MDIN3 Table 16 P15/P11 connector data Manufacturer Mfg. P/N Mating connector 54F-10202GDD2 Standard Ethernet RJ45 plug NOTE: The actual number of Gigabit Ethernet ports available depends on the CM-A510 Ethernet configuration option. -
Page 17: Dvi Connector (J4)
Interfaces and Connectors DVI Connector (J4) The SB-A510 is equipped with a standard HDMI socket (J4) providing a DVI interface. The on-board DVI transmitter IC drives the DVI signals through the HDMI socket. For additional details, please refer to section 3 .2 of this document. The DVI_DDCSCL and DVI_DDCDAT signals are routed to the CM-A510 I2C port 0 signals, and provide DVI DDC interface. -
Page 18: Lcd Fpc (P13)
Interfaces and Connectors LCD FPC (P13) The on-board LCD FPC connector (P13) allows easy integration with custom LCD panels. The CABFPC40 and CONLCD-GEN accessories (supplied by CompuLab) provide a generic 100-mil 7 header connection. For additional details, please refer to section of this document. -
Page 19: Lvds Header (P9)
Interfaces and Connectors LVDS Header (P9) LVDS output signals are routed from the LVDS Transmitter IC to the onboard 100mil header (P9). 3 .3 For additional details, please refer to section of this document. In order to use the LVDS interface, CM-A510 display system must be set to RGB 888 operation mode. -
Page 20: Power Output Terminals (P17, P19)
Interfaces and Connectors 4.11 Power Output Terminals (P17, P19) The SB-A510 is equipped with two power output terminals. The power output terminals (P17 & P19) are provided for the S-ATA hard drive power supply. Table 24 P17 connector pinout Signal Name VCC_12V Table 25 P19 connector pinout... -
Page 21: S/Pdif Connectors (P22, U6)
Interfaces and Connectors 4.13 S/PDIF Connectors (P22, U6) The CM-A510 S/PDIF interface can be accessed through the P22 Standard RCA connector (populated by default) or through the U6 optical transceiver (not populated by default) on the SB- A510. Table 28 P22 connector pinout Signal Name SPDIF_BASE... -
Page 22: Compulab Video Input Fpc (P25)
Interfaces and Connectors 4.14 CompuLab Video Input FPC (P25) The on-board CompuLab Video Input FPC connector (P25) allows direct integration with the CompuLab Video Input module. P25 is connected to the CM-A510 Camera interface. Table 32 P25 connector pinout Signal Name... -
Page 23: Mmc/Sd/Sdio Socket (P5)
Interfaces and Connectors 4.15 MMC/SD/SDIO Socket (P5) The SB-A510 MMC/SD/SDIO interface is based on the SD-0 interface of the CM-A510. The MMC controller signals are routed to the standard MMC/SD socket (P5). P5 power is supplied by the VCC_MMC voltage rail. VCC_MMC can be enabled/disabled by GPIO13 on the on-board I2C GPIO extender IC. -
Page 24: Misc. Signals Headers (P14, P21)
Interfaces and Connectors 4.17 MISC. Signals Headers (P14, P21) Two 100mil headers (P14 & P21) provide access to miscellaneous CM-A510 interfaces. Table 38 P14 connector pinout Signal Name Signal Name UART2_TXD/GPIO14 CAM_MCLK/GPIO32 CAM_D5/GPIO29 CAM_D0/GPIO24 CAM_D2/GPIO26 CAM_D6/GPIO30 CAM_VSYNC/GPIO34 UART1_RXD/GPIO62 CAM_HSYNC/GPIO33 CAM_D7/GPIO31 CAM_I2C_SCK CAM_D1/GPIO25 CAM_D3/GPIO27... -
Page 25: Boot Source Button (Sw1)
Interfaces and Connectors 4.19 Boot Source Button (SW1) The SB-A510 features a user-accessible boot source button (SW1). Pressing this button during power-up or reset will cause the CM-A510 to boot with the alternate boot option (S-ATA hard drive). 4 .22 NOTE: Jumper E6 may override button SW1. -
Page 26: Jumpers
Interfaces and Connectors 4.22 Jumpers The SB-A510 jumpers configure SB-A510 sub-systems and CM-A510 operation modes. The table below summarizes all jumpers and their possible configurations. Table 41 Jumpers description Shorted SB-A510 Jumper Description Pins sub-System 1 & 2 PCI-E link connected to mini PCI-E slot (P4) PCI-E mux 2 &... -
Page 27: Mechanical Drawings
Mechanical Drawings MECHANICAL DRAWINGS Figure 3 SB-A510 top Revised May 2011 SB-A510 Rev 1.1... - Page 28 Mechanical Drawings Figure 4 SB-A510 bottom (X-Ray view - as seen from top side) Mechanical drawings are available in DXF format from CompuLab's website, following [Developer] >> [SB-A510] >> [SB-A510 – schematics, dimension, layout] links. Revised May 2011 SB-A510 Rev 1.1...
-
Page 29: Operational Characteristics
Operational Characteristics OPERATIONAL CHARACTERISTICS Absolute Maximum Ratings Parameter Unit Main power supply voltage NOTE: Stresses beyond Absolute Maximum Ratings may cause permanent damage to the device. Recommended Operating Conditions Parameter Condition Unit Main power supply voltage 12 Volt is not used by PCI or P19 Main power supply voltage 12 Volt is used by PCI or P19 See Note... -
Page 30: Operating Temperature Ranges
Operational Characteristics Operating Temperature Ranges The information in this section refers to the SB-A510 board only. For temperature ranges of off-board components such as the LCD panels or hard drives, please refer to the component’s datasheet. The SB-A510 is available with three options of operating temperature range: Table 43 Operating Temperature Ranges Range... -
Page 31: Accessories
Connects directly to P12 on the SB-A510. FPC cable, 0.5mm, 40-pos Used with CONLCD-GEN and 410X60400 CABFPC40 CompuLab Video Input module General purpose LCD interface module. Used in combination with CABFPC40 to provide a generic LCD interface. 503R101301 CONLCD-GEN Connects to P13 on the SB-A510.