Related Manuals for Pfaff 114
Summary of Contents for Pfaff 114
-
Page 1: Instruction Manual
Instruction Manual This instruction manual applies to machines from the following serial numbers onwards: # 6 001 000 296-12-18 613/002 Betriebsanleitung engl. 12.04... - Page 2 As an alternative to the internet download the adjustment manual can also be ordered in book form under part no. 296-12-18 614/002. The reprinting, copying or translation of PFAFF Instruction Manuals, whether in whole or in part, is only permitted with our previous authorization and with written reference to the source.
-
Page 3: Table Of Contents
Contents Contents ................. Chapter - Page Safety ........................... 1 - 1 Directives ........................1 - 1 General notes on safety ....................1 - 1 Safety symbols ......................1 - 2 Important points for the user ..................1 - 2 Operating and specialist personnel ................1 - 3 .05.01 Operating personnel ...................... -
Page 4: Contents
Contents Contents ................. Chapter - Page Preparation ........................9 - 1 Inserting the needle ...................... 9 - 1 Winding the bobbin thread .................... 9 - 2 Removing / Inserting the bobbin case ................9 - 3 Threading the bobbin case / adjusting the bobbin thread tension ........9 - 3 Threading the needle thread / Adjusting the needle thread tension ...... -
Page 5: Safety
Safety Safety Directives This machine is constructed in accordance with the European regulations contained in the conformity and manufacturer’s declarations. In addition to this Instruction Manual, also observe all generally accepted, statutory and other regulations and legal requirements and all valid environmental protection regulations! The regionally valid regulations of the social insurance society for occupational accidents or other supervisory organizations are to be strictly adhered to! General notes on safety... -
Page 6: Safety Symbols
It is the obligation of the user to ensure that none of the safety mechanisms are removed or deactivated. It is the obligation of the user to ensure that only authorized persons operate and work on the machine. Further information can be obtained from your PFAFF agent. 1 - 2... -
Page 7: Operating And Specialist Personnel
Safety Operating and specialist personnel Operating personnel .05.01 Operating personnel are persons responsible for the equipping, operating and cleaning of the machine as well as for taking care of problems arising in the sewing area. The operating personnel is required to observe the following points and must: always observe the Notes on Safety in the Instruction Manual! never use any working methods which could adversely affect the safety of the machine! not wear loose-fitting clothing or jewelery such as chains or rings! -
Page 8: Danger
Safety Danger A working area of 1 meter is to be kept free both in front of and behind the machine while it is in operation so that it is always easily accessible. Never reach into the sewing area while sewing! Danger of injury by the needle! Never leave objects on the table while adjusting the machine settings! Objects can become trapped or be slung away! Danger of injury! 110-001... -
Page 9: Proper Use
Proper use Proper use The PFAFF 114 is a lockstitch, zig-zag sewing machine with bottom feed. The machine is used for sewing zig-zag seams in the craft sector. Any and all uses of this machine which have not been approved of by the... -
Page 10: Specifications
Specifications Specifications Stitch type: ..................304 (zigzag lockstitch) Needle system: ......................DPx5 Needle size in 1/100 mm: ..................80 - 100 Model B: ..............for sewing medium-weight material Effective balance wheel diameter: ................74 mm Presser foot clearance: ....................6 mm Clearance width: .................... -
Page 11: Disposal Of Machine
Disposal of machine Disposal of machine The proper disposal of the machine is the responsibility of the customer. The materials used in the machines are steel, aluminium, brass and various plastics. The electrical equipment consists of plastics and copper. The machine is to be disposed of in accordance with the locally valid environmental protection regulations. -
Page 12: Transport, Packaging And Storage
Transport, packaging and storage Transport, packaging and storage Transport to the customer’s premises The machines are delivered completely packed. Transport within the customer’s premises The manufacturer bears no liability for transport within the customer’s premises or to the in- dividual locations of use. Make sure that the machines are always transported upright. Disposal of the packaging The packaging of these machines consists of paper, cardboard and VCE fiber. -
Page 13: Explanation Of The Symbols
Explanation of the symbols Explanation of the symbols In the following section of this Instruction Manual, certain tasks or important pieces of information are accentuated by symbols. The symbols used have the following meanings: Note, information Cleaning, care Lubrication, greasing Servicing, repairing, adjustment, maintenance (only to be carried out by specialist personnel) 6 - 1... -
Page 14: Controls
Controls Controls On/off switch Switch the machine on or off by turning main switch 1. Fig. 7 - 01 Pedal Machine stop Fig. 7 - 02 7 - 1... -
Page 15: Presser Foot Lift Lever
Controls Presser foot lift lever The presser foot is raised by raising lever 1. Fig. 7 - 03 Stitch length adjustment wheel To adjust the stitch length turn the stitch length adjustment wheel 1. The stitch length setting can be read on the scale. -
Page 16: Zig-Zag Stitch Lever
Controls Zig-zag stitch lever To adjust the width of the zig-zag stitch operate the zig-zag stitch lever 1. Fig. 7 - 05 Limiting and setting the zig-zag stitch By tightening screw 1 the maximum zig- zag stitch width can be limited, see Chapter 9.07 Setting the zig-zag stitch width. -
Page 17: Stitch Position Adjustment Lever
Controls Stitch position adjustment lever To set the required stitch position adjust the stitch position adjustment lever 1. Position "A" = stitch positioned to the left Position "O" = stitch positioned in the centre Position "B" = stitch positioned to the right Fig. -
Page 18: Setting The Straight Stitch
Controls Setting the straight stitch The straight stitch may only be set if no zig-zag stitch has been selected. Danger of damage to the machine! Set the position of the needle bar frame by tightening adjusting screw 1. Fig. 7 - 09 Knee lever Depending on the type of assembly, by pressing knee lever 1 either the presser... -
Page 19: Installation And Commissioning
Installation and commissioning Installation and commissioning The machine must only be installed and commissioned by qualified personnel! All relevant safety regulations must be strictly adhered to! If the machine is delivered without a table, be sure to use a stand and table top that can hold the weight of the machine with its motor. -
Page 20: Fitting The Top V-Belt Guard
Installation and commissioning Fitting the top V-belt guard .01.02 Fig. 8 - 02 Fasten belt guard 1 with screws 2. Fasten belt guard 3 with screws 4. Fitting the bottom V-belt guard .01.03 Attach the bottom V-belt guard as specified in the motor Instruction Manual. 8 - 2... -
Page 21: Fitting The Reel Stand
Installation and commissioning Fitting the reel stand .01.04 Fit the reel stand as shown in Fig. 8 - 03. Afterwards insert the stand in the hole in the table top and secure it with nuts pro- vided. Fig. 8 - 03 Connecting the earth cables .01.05 Screw the earth cables from the sewing... -
Page 22: Commissioning
Installation and commissioning Commissioning Examine the machine, in particular the electric cables, for any damage. Before commissioning the machine, clean it thoroughly and then oil it, see Chapter 10 Care and Maintenance! The machine may only be connected to an earthed socket! Have qualified personnel check whether the machine’s motor can be operated with the available voltage and whether it is connected properly. -
Page 23: Table Top Cutout
Installation and commissioning Table top cutout. 8 - 5... -
Page 24: Preparation
Preparation Preparation All regulations and instructions in this Instruction Manual are to be observed! Special attention is to be paid to the safety regulations! All preparation work is only to be carried out by appropriately trained personnel. Before all preparation work, the machine is to be separated from the electricity supply by removing the plug from the mains or switching off the On/Off switch! Inserting the needle Switch off the machine! -
Page 25: Winding The Bobbin Thread
Preparation Winding the bobbin thread 110-016 1 mm Fig. 9 - 02 Place empty bobbin 1 on bobbin winder spindle 2. Thread the thread as shown in Fig. 9.02 and wind it around bobbin 1 a few times in a clockwise direction. -
Page 26: Removing / Inserting The Bobbin Case
Preparation Removing / Inserting the bobbin case Switch off the machine! Danger of injury due to unintentional starting of the machine! Removing the bobbin case: Raise latch 1 and remove bobbin case 2. Inserting the bobbin case: Press bobbin case 2 until you feel it snap into the bobbin case base. -
Page 27: Threading The Needle Thread / Adjusting The Needle Thread Tension
Preparation Threading the needle thread / Adjusting the needle thread tension Fig. 9 - 05 Switch off the machine! Danger of injury due to unintentional starting of the machine! Thread the machine as shown in Fig. 9-05. Adjust the needle thread tension by turning the milled screw 1. 9 - 4... -
Page 28: Adjusting The Stitch Length
Preparation Adjusting the stitch length Set the required stitch length with the stitch length adjustment wheel 1. Fig. 9 - 06 Adjusting the width of the zig-zag stitch Short period of work with zig-zag stitch Set the required width of the zig-zag stitch by operating zig-zag stitch lever 1. -
Page 29: Adjusting The Stitch Position
Preparation Adjusting the stitch position Set the required stitch position with stitch position adjustment lever 1. Position "A" = stitch positioned to the left Position "O" = stitch positioned in the centre Position "B" = stitch positioned to the right Fig. -
Page 30: Care And Maintenance
Care and maintenance Care and maintenance Maintenance intervals Cleaning .............. daily, several times if in continuous use Oiling the hook ............ daily, several times if in continuous use Oiling the machine ..................once a week During all cleaning work the machine must be disconnected from the power supply by switching off the main switch or pulling out the plug! Danger of injury if the machine is started accidentally! Cleaning the machine... -
Page 31: Oiling The Hook
22.0 mm /s at 40°C and a density of 0.865 g/cm Fig. 10 - 02 15°C. We recommend PFAFF sewing machine oil, part no. 280-1-120 144. Oiling the machine Oiling points on the machine head .04.01 Switch off the machine! -
Page 32: Oiling Points In The Arm Cover And Bed Plate
Pour a few drops of oil once a week into the holes marked, see arrows in Fig. 10-04. Only use oil with a mean viscosity of 22.0 mm /s at 40°C and a density of 0.865 g/cm at 15°C. We recommend PFAFF sewing machine oil, part no. 280-1-120 144. 10 - 3... -
Page 33: Oiling Points Under The Bed Plate
We recommend PFAFF sewing machine oil, part no. 280-1-120 144. Apply fresh grease to the bevel gears 1 and 2 as required. We recommend PFAFF sodium soap grease with a dripping temperature of ca. 150° C, part no. 2801-1-120 243. -
Page 34: Wearing Parts
A detailed parts list for the complete machine is included with the accessories. In case of loss, the parts list can be downloaded from the internet address www.pfaff-industrial.com/de/service/download/index.php3. As an alternati- ve to the internet download the parts lists can also be ordered in book form under part no. - Page 35 Notes...
-
Page 36: Postfach
PFAFF Industrie Maschinen AG Postfach 3020 D-67653 Kaiserslautern Königstr. 154 D-67655 Kaiserslautern Telefon: (0631) 200-0 Telefax: (0631) 17202 E-Mail: info@pfaff-industrial.com...