Sanyo VPC-S122EXBL Service Manual page 16

PZ_SW_B_C: PZ2
PZ2: adjustment value of zoom PR switch position 2
(1051<=PZ2+PBR<=1116)
PZ_SW_C_B: PZ3
PZ3: adjustment value of zoom PR switch position 3
(1006<=PZ3+PBR<=1116)
PZ_BR: PBR
PBR: adjustment value of zoom backrush pulse
(0<=PBR<=45)
PZ_SP: PSP
PSP: adjustment value of zoom sink pulse
(210<=PSP<=320)
AF_SW: ASW
ASW: adjustment value of focus PI switch position
(893<=ASW<=985)
AF_BR: ABR
ABR: adjustment value of focus backrush pulse
(0<=ABR<=12)
AF_WIDE: ZW
ZW: adjustment value of focus at zoom position wide
(–54<=ZW<=47)
AF_MID1: ZM1
ZM1: adjustment value of focus at zoom position middle1
(–86<=ZM1<=48)
AF_MID2: ZM2
ZM2: adjustment value of focus at zoom position middle2
(–114<=ZM2<=57)
AF_MID3: ZM3
ZM3: adjustment value of focus at zoom position middle3
(–107<=ZM3<=76)
AF_TELE: ZT
ZT: adjustment value of focus at zoom position tele
(–108<=ZT<=94)
2. AWB Adjustment
Camera
Preparation:
POWER switch: ON
Setting of pattern box:
Color temperature: 3100 ± 20 (K)
Luminance: 900 ± 20 (cd/m
Pattern box
(color viewer)
2 )
Adjusting method:
1. Set a distance of 0.5-1.0 cm between the pattern box and
the camera when zoom wide edge. (Do not enter any light.)
2. Double-click on the DscCalDi.exe.
3. Click the AWB, and click the Yes.
4. AWB adjustment value will appear on the screen.
5. Click the OK.
Dsc Calibration
AWB Results:
1:
AGC=265,410,597,759,926,
772,943
AGC_OLD=242
6F_AGC=0,1,0,0,0
WB=295,510,562
CHECK=128,128,149
MS=4428,4578
Fno_FOR_ISO=32
SS_FOR_ISO=4181
YLEVEL_FOR_ISO=9855
AR=983,1219
AR_3H2V=896,1112
Adjustment value determination is effectuated using "AGC",
"AGC_OLD", "6F_AGC", "CHECK", "MS", "AR" and "AR_3H2V"
values.
If AGC=a1, a2, a3, a4, a5, a6, a7, AGC_OLD=ao1,
6F_AGC=fd1, fd2, fd3, fd4, fd5, CHECK=wc0, wc1, wc2,
MS=ms1, ms2, AR=ar, arm, AR_3H2V=ar2, arm2 and the ad-
justment values fulfill the conditions below, they are determined
as within specifications.
Adjustment value determination
0<=a1<=350, 0<a2<1023, 0<a3<1023, 0<a4<1023,
0<a5<1023, 0<a6<1023, 0<a7<1023
0<ao1<1023
fd1<=10, fd2<=10, fd3<=10, fd4<=10, fd5<=10
wc0=128 ± 2, wc1=128 ± 2, wc2=130 ± 40
3400<=ms1<=5300, 3450<=ms2<=5350
500<=ar<=1500, 500<=arm<=1500,
500<=ar2<=1500, 500<=arm2<=1500
Adjustment values other than the above are irrelevant.
3. CCD White Point Defect Detect Adjustment
Preparation:
POWER switch: ON
Adjustment method:
1. Double-click on the DscCalDi.exe.
2. Select "CCD Defect" on the LCD "Test", and click the "Yes".
3. After the adjustment is completed, OK will display.
4. Click the OK.
– 16 –
x
OK
Copy