Cushman 84043 Operation Manual
Turf truckster
Hide thumbs
Also See for 84043:
- Parts & maintenance manual (185 pages) ,
- Maintenance manual (186 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Cushman 84043
Summary of Contents for Cushman 84043
- Page 1 By Jacobsen Safety & Operation Manual Cushman Turf Truckster 84043 – Perkins 403C-11 Diesel Engine, MT 84044 – Perkins 403C-11 Diesel Engine, MT, EC 84056 – Suzuki K6 Gas Engine, MT 84057 – Suzuki K6 Gas Engine, AT 84061 – Suzuki K6 Gas Engine, RV and Utility...
-
Page 2: Table Of Contents
CONTENTS 5 ....... . . OPERATION CONTENTS 1 ........SAFETY Daily Inspection .......... -
Page 3: Safety
SAFETY SAFETY OPERATING SAFETY ______________________________________________________ WARNING EQUIPMENT OPERATED IMPROPERLY OR BY UNTRAINED PERSONNEL CAN BE DANGEROUS. Familiarize yourself with the location and proper use of all controls. Inexperienced operator’s should receive instruction from someone familiar with the equipment before being allowed to operate the machine. Safety is dependent upon the awareness, concern and 12. -
Page 4: Important Safety Notes
SAFETY IMPORTANT SAFETY NOTES _______________________________________________ This safety alert symbol is used to alert you to potential hazards. DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. -
Page 5: Vehicle Identification Numbers
Augusta Georgia, USA The serial number is also stamped on the cross member. following U.S. patents: 1 800 241 5855 It is located to the left of the Nameplate/Identification MODEL 84043 Decal. DATE CODE M1903 LABEL # 75984G55 NOTE: Reference to the Front, Rear, Left and Right sides... -
Page 6: Decals
DECALS DECALS DECALS _________________________________________________________________ Familiarize yourself with the decals. They are critical to the safe operation of the machine. REPLACE DAMAGED DECALS IMMEDIATELY. NOTICE WARNING THIS UNIT IS NOT A MOTOR VEHICLE WITHIN THE PARKING BRAKES ARE NOT AUTO- DEFINITION OF THE NATIONAL TRAFFIC MOTOR MATICALLY APPLIED. -
Page 7: Controls
CONTROLS ICONS ___________________________________________________________________ CONTROLS Hour Meter Ignition Switch Read Manual Engine Throttle Start High STOP Coolant Brake Fuel Governor Control Temperature Throttle Governor Parking Service Turn Indicators Engine Oil Pressure Glow Plug High Beam Left Right WARNING Never attempt to drive this vehicle unless you have read the Safety and Operation Manual and know how to operate all controls correctly. - Page 8 CONTROLS Tachometer Horn Button Hour Meter Clutch Pedal W Service Brake Pedal Fuel Gauge Voltmeter Accelerator Pedal Temperature Gauge Differential Shift Cable Turn Signal Indicator Parking Brake Lever AA Remote Hydraulics Control Oil Pressure Light AB Hydraulic Lift Control Glow Plug Light Service Brake Fluid Light Parking Brake Light High Beam Indicator...
-
Page 9: Control Descriptions
CONTROLS CONTROL DESCRIPTIONS __________________________________________________ K. Parking Brake Light - Indicates parking brake is engaged. Do not drive unit without disengaging parking brake. L. High Beam Indicator - Indicates light switch (T) is in high beam position. COOLANT x 100 HOURS 0 0 0 0 STOP START... - Page 10 CONTROLS Automatic Transmission: Gear selector has six R. Hand Throttle - Used to set engine speed for remote positions, Park (P), Reverse (R), Neutral (N), Drive operations. Increasing hand throttle speed will depress accelerator pedal. (D), second (2) and Low (L). Engine will not start unless selector is in Park (P) or Neutral (N).
- Page 11 CONTROLS W. Service Brake Pedal - Depress the pedal to slow or Z. Parking Brake Lever - The park brake lever is stop the vehicle. located to the left side of the drivers seat. To engage the brake, pull up on the lever until park If the brakes DO NOT stop the vehicle properly, the brake is applied.
-
Page 12: Operation
OPERATION DAILY INSPECTION________________________________________________________ OPERATION 2. Check the fuel supply, radiator coolant level, CAUTION crankcase oil and air cleaner indicator. All fluids must be at the full level mark with engine cold. The daily inspection should be performed only when 3. Check tires for proper inflation. the engine is off and all fluids are cold. -
Page 13: Operating Procedures
OPERATION OPERATING PROCEDURES _________________________________________________ WARNING A Rollover Protection Structure (ROPS) for this truck is available as an optional accessory. Evaluate the terrain and working conditions to determine if a ROPS is required. Seat belts must be worn whenever a ROPS is installed on the tractor. -
Page 14: Starting
OPERATION STARTING _______________________________________________________________ IMPORTANT: Do not use starting assist fluids. Use of such fluids in the air intake system may be potentially explosive or cause a “Runaway” engine condition and could result in serious engine damage. COOLANT 1. Make sure fuel shut off valve is completely open. 2. -
Page 15: To Drive Vehicle
OPERATION TO DRIVE VEHICLE ________________________________________________________ Read and follow all safety notes contained in this manual If the engine rpm and/or the vehicle speed are not when driving vehicle. Refer to Section 5.3 for general decreased sufficiently and you try to down shift, it is possible to damage the transmission. -
Page 16: Ground Speed
OPERATION GROUND SPEED __________________________________________________________ Refer to Figure 5B to determine desired ground speed The decals are applied to each of the appropriate turf and engine RPM to select proper gear for operating the models and are shown below with correct model identity. vehicle. -
Page 17: Stopping And Parking The Vehicle
OPERATION STOPPING AND PARKING THE VEHICLE ______________________________________ Before you leave the operator’s seat, complete these 2. Move the gear selector lever to Park (P) position steps in the following order. and apply the parking brake remove your foot from the brake pedal, turn the keyswitch to the OFF NOTE: When parking the vehicle on an incline, the front position remove... -
Page 18: Hydraulic System
OPERATION HYDRAULIC SYSTEM ______________________________________________________ The hydraulic system on this vehicle is refered to as a To use a hydraulic accessory, connect accessory hose (9) to hose (8) and accessory hose (10) to connector (7). “live” system. This means the hydraulic pump operates whenever the engine is running. -
Page 19: Engine Overheat Procedure
OPERATION 5.10 ENGINE OVERHEAT PROCEDURE ___________________________________________ During vehicle operation, if the water temperature gauge Temperature gauge needle should start to go down shows 230° F (110° C) or above, and/or the overheat approximately 30 seconds after the screen is cleaned. If warning buzzer sounds, follow this procedure. -
Page 20: Hillside Operation
OPERATION 5.12 HILLSIDE OPERATION _____________________________________________________ terrain or when the grass is wet. Wet grass reduces WARNING traction and steering control. To minimize the possibility of overturning, the safest 1. If the vehicle tends to slide or the tires begin to method for operating on hills and terraces is to travel “mark”... -
Page 21: Notes
NOTES NOTES... - Page 22 Equipment from Jacobsen is built to exacting standards ensured by ISO 9001 and ISO 14001 registration at all of our manufacturing locations. A worldwide dealer network and factory trained technicians backed by Textron Parts Xpress provide reliable, high-quality product support. Textron Golf, Turf &...