Page 2
For parts or service contact SANYO Fisher Service Corporation 21605 Plummer Street Chatsworth, CA 91311 (U.S.A.) 300 Applewood Crescent, Concord, Ontario L4K 5C7 (CANADA) January / 2005 / 2000 SMC Printed in U.S.A.
If the Service Manual Chassis No. does not match the unit’s, additional Service Literature is required. This chassis is similar to Chassis No. 25520-00, however, all Service Information is given in this Notice for Chassis No. 25520-04 used in Model DS25520. Specifications Contents Power Rating .
SAFETY INSTRUCTIONS SAFETY PRECAUTIONS WARNING: The chassis of this receiver has a floating READING SHOULD NOT EXCEED 750 mV. AC VOLTMETER ground with the potential of one half the AC line voltage in (5000 ohms per volt or more sensitivity) respect to earth ground.
SERVICE ADJUSTMENTS GENERAL This set has an On-screen Service Menu system included in the CPU that allows remote operation for most of the service adjustments. To enter the Service Menu, first disconnect the AC power cord. Then while pressing the MENU key on the front control panel, recon- nect the AC power cord.
Page 6
Table 1. ON-SCREEN SERVICE MENU When IC802 (EEPROM) is replaced, check the bus data to confirm they are the same as below. The shaded menu should be checked and be set up or readjusted according to the procedures described in the following pages. Initial Setup Data marked with an * should be changed from Initial Reference Data.
Page 7
Table 1. ON-SCREEN SERVICE MENU (Continued) When IC802 (EEPROM) is replaced, check the bus data to confirm they are the same as below. The shaded menu should be checked and be set up or readjusted according to the procedures described in the following pages. Initial Setup Data marked with an * should be changed from Initial Reference Data.
Page 8
SERVICE ADJUSTMENTS (Continued) DRIVE / BIAS ADJUSTMENTS PROGRAM CODES Note 3. Red/Blue Drive Adjustments in Service Menu NO. The microprossesor used in this model is a multi-purpose 72 DRV: Adjust Red and Blue Drive Levels alternately with type and is used in several different models. To ensure 1, 3, 7, and 9 keys on the remote control.
Page 9
ANTENNA CONNECTIONS VCO ADJUSTMENT This receiver is designed for UHF/VHF reception. A 75 ohm Note: VCO must be adjusted after IC101 (Signal Processor), terminal is provided for UHF and VHF receptions. When IC802 (EEPROM) or T151 (VCO Coil) is replaced. connecting a CATV antenna system, connect the 75 ohm 1.
Page 10
SERVICE ADJUSTMENTS (Continued) GRAYSCALE ADJUSTMENT BRIGHTNESS LEVEL ADJUSTMENT 1. Set the picture controls to the Sports levels or Reset Note: Grayscale, RF AGC, Video Level, and High Voltage Check (use MENU key and key or RESET key). must be adjusted before attempting Brightness Level 2.
Page 11
SOUND ADJUSTMENT SEPARATION ADJUSTMENT 1. Connect a color-bar generator to the antenna terminals 7. Turn off the receiver and disconnect the AC power cord with audio signal of 1KHz at 100% modulation. (AC 120V line). 2. Set the picture controls to the Sports levels 8.
PURITY AND CONVERGENCE ADJUSTMENTS CAUTION: The Purity and Convergence adjustments have been made at the factory. Readjustments should be made only after the picture tube or deflection yoke is replaced. Follow the steps below for necessary readjustments. PURITY ADJUSTMENTS 1. When replacing picture tube or deflection yoke, mount deflection yoke and purity and convergence magnets DEFLECTION YOKE assembly properly.
CONVERGENCE ADJUSTMENT CENTER CONVERGENCE ADJUSTMENT OUTER AREA CONVERGENCE ADJUSTMENT 1. Connect a crosshatch generator to antenna terminals. The outer area convergence is performed by positioning of 2. Set Contrast to low level to eliminate blooming. Reduce the yoke as follows: Brightness level to obtain black background if necessary.
SERVICE HINTS POWER FAILURE DETECTOR This unit is equipped with a Power Failure Detector function included in the CPU which checks for an abnormal condition in the chassis power supplies, including the power supply derived from the Horizontal Output Transformer. If, while the power is on, a failure is caused by any of the following that results in a low voltage supply, the CPU will turn the unit off in 1.5 seconds to prevent unnecessary damage: •...
MECHANICAL DISASSEMBLIES CHASSIS REMOVAL CABINET BACK REMOVAL 1. Remove cabinet back. 1. Refer to Figure 1, remove 8 screws. 2. Discharge the picture tube anode (2nd anode lead) to the 2. Pull off cabinet back and remove. dag coating (picture tube grounding lead). 3.
CHASSIS ELECTRICAL PARTS LIST CAUTION: To Protect against electrical shock and for continued product safety, refer to SAFETY PRECAUTIONS, X-RADIATION PRECAUTIONS, HIGH VOLTAGE HOLD-DOWN TEST, and PRODUCT SAFETY NOTICE on Page 2. PRODUCT SAFETY NOTICE PRODUCT SAFETY SHOULD BE CONSIDERED WHEN A REPLACEMENT IS MADE IN ANY AREA OF A RECEIVER. COMPONENTS INDICATED BY A STAR ( ) IN THIS PARTS LIST AND THE SCHEMATIC DIAGRAM DESIGNATE COMPONENTS IN WHICH SAFETY CAN BE OF SPECIAL SIGNIFICANCE.
Page 17
Schematic Schematic Part No. Part No. Description Description Location Location C285 403 224 6108 CERAMIC 0.01U K C631 404 088 2909 CERAMIC 1000P M 250V C401 404 084 3306 ELECT 470U M 404 088 7102 CERAMIC 1000P M 250V C402 403 224 6108 CERAMIC 0.01U K...
COMPONENT AND TESTPOINT LOCATIONS MAIN BOARD PARTS SIDE CAUTION FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE, REPLACE ONLY WITH THE SAME TYPE 4A, 125V FUSE. ATTENTION : POUR MAINTENIR LA PROTECTION CONTRE LES RISQUES D’ INCENDIE UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE 4A, 125V.
Page 26
PIC TUBE SOCKET BOARD COMPONENTS Part Loc. Q701 Q711 Q721 For parts or service contact SANYO Fisher Service Corporation 21605 Plummer Street Chatsworth, CA 91311 (U.S.A.) 300 Applewood Crescent, Concord, Ontario L4K 5C7 (CANADA) April / 2003 / 2000 SMC Printed in U.S.A.
MODEL DS25520 Chassis No. 25520-04 WAVEFORMS CAUTION FOR CONTINUED PROTECTION AGAINST SCHEMATIC DIAGRAMS A RISK OF FIRE, REPLACE ONLY WITH Note: Voltages were measured with offset color-bar signal and controls set for normal picture. THE SAME TYPE 4A, 125V FUSE.
Page 28
MODEL DS25520 Chassis No. 25520-04 TUNER C1051 16EM22LBWA Y IN A101 K1051 F1BAM0280 D1051 R1051 :F1BAM0290 S/COMP SW 1/10GJ75C C IN AV1/AV2 SW C1052 R1082 R1081 1/10GJ22KC 1/10GJ22KC KK0.01LZB R1052 S-VIDEO OUT D1052 15 16 1/10GJ75C 17 18 R1004 R1007...
Page 30
For parts or service contact SANYO Fisher Service Corporation 21605 Plummer Street Chatsworth, CA 91311 (U.S.A.) 300 Applewood Crescent, Concord, Ontario L4K 5C7 (CANADA) April / 2002 / 2000 SMC Printed in U.S.A.