GE GTUP240GM4WW Installation Instructions Manual page 8

Installation Instructions
STANDARD REAR EXHAUST
(Vented above floor level}
U
ECOMMENDED
ONFIGURATION
O MINIMIZE
XHAUSTBLOCKAGE
ELBOW HIGHLY
RECOMMENDED
2
NOTE: ELBOWS WILL PREVENT DUCT KINKING AND COLLAPSING
[8]LEVELING AND STABILIZING YOUR
APPLIANCE
_.__E LEVEL
-TO-SIDE
LEVEL
FRONT-TO-BACK.
2LEVELING LEGS
Level and stabilizing your appliance
1. Carefully move the appliance to its final location.
Gently rock the appliance into position. It is important
not to damage the rubber leveling legs when moving
your appliance to its final location. Damage legs can
increase appliance vibration. It may be helpful to
spray window cleaner on the floor to help move your
appliance to its final position.
Note: do not use washer cover to lift the unit.
2. To ensure the appliance is level and solid on all four
legs, tilt the appliance forward so the rear legs are off
the ground. Gently set the appliance back down to
allow the rear legs to self adjust.
3. With the appliance in its final position, place a level on
top of back part of the washer lid and check it side to
side, then check front to back. Screw the front leveling
legs up or down to ensure the appliance is resting solid
on all four legs (no rocking or the appliance should
exist), turn the lock nuts on each leg up toward the base
of the unit and snug with a wrench.
Note: Keep the leg extension at minimum to prevent
excessive vibration. The farther out legs are extended, the
more the unit will vibrate.
CONNECTING THE DRYER TO HOUSE
VENT
RIGIDMETAL TRANSITION DUCT
• For best drying performance, a rigid metal transition duct is
recommended.
• Rigidmetal transitions ducts reduce the risk of crushing and
kinking.
UL-LISTED FLEXIBLE METAL (SEMI-RIGID) TRANSITION DUCT
• tf rigid metal duct cannot be used,then UL-listedflexible metal
(semi-rigid)ducting can be used (KitWX08X10077).
• Never install flexible metal duct in walls, ceilings, floors or
other enclosedspaces.
For many applications,installing elbows at both the dryer and
the wall is highly recommended(seeillustrations on page 9).
Elbowsallow the dryer to sit closeto the wall without kinking
and or crushing the transition duct, maximizing drying
performance.
Avoidresting the duct on sharp objects.
UL-LISTED FLEXIBLE METAL (FOIL-TYPE} TRANSITION DUCT
• tn special installations, it may be necessary to connect the
dryer to the housevent usinga flexible metal (foiltype)duct.
A UL-listedflexible metal (foil-type)ductmay be usedONLY in
installations where rigid metal or flexible metal (semi-rigid)
ducting cannot be used AND where a 4" diameter can be
maintained throughout the entire length of the transition
duct.
tn Canadaand the United States,only the flexible metal(foil-
type) ducts that comply with the "Outline for Clothes Dryer
Transition DuctSubject 2158A"shallbe used.
Total length of flexible metal duct should not exceed 8 feet
(2.4m).
• Avoidresting the duct on sharp objects.
• For best drying performance:
1. Slideone end of the duct over the clothes dryeroutlet pipe.
2. Securethe duct with a clamp.
3. With the dryer in its permanent position,extendthe duct to
its full length.Allow 2" of duct to overlap the exhaustpipe.
Cut off and removeexcess duct. Keepthe duct as straight
as possiblefor maximum airflow.
/4.Securethe duct to the exhaustpipe with the other clamp.
8