SERVICE MANUAL This Service Manual is for the HT2-M200(E1T12ED) / HT2-M200(E1T13ED) model. For the HT2-M200(E1T12ED) / HT2-M200(E1T13ED) model, the letter (E1T12ED) / (E1T13ED) is printed on the Rating Label on the back of the unit. Refer to the Rating Label below.
LASER BEAM SAFETY PRECAUTIONS This BD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on.
IMPORTANT SAFETY PRECAUTIONS Product Safety Notice K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the Some electrical and mechanical parts have special AC outlet. safety-related characteristics which are often not L. When reassembling, be sure to use the original evident from visual inspection, nor can the protection screws or specified screws listed in the parts list.
Page 6
Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the Chassis or Secondary Conductor specified values to verify compliance with safety standards.
STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is When soldering, be sure to use the Pb free solder. indicated as shown. How to Remove / Install Flat Pack-IC Top View Bottom View 1.
Page 8
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
Page 9
With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
Page 10
Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart Note: (1) Identification (location) No. of parts in the figures This flowchart indicates the disassembly steps to gain (2) Name of the part access to item(s) to be serviced. When reassembling, (3) Figure Number for reference follow the steps in reverse order.
Page 14
3. How to Eject a Disc When a disc cannot be removed due to malfunction or when an unplayable disc is inserted, follow the procedure below to remove the disc. Procedure A 1. Unplug the AC power cord and then plug it in. 2.
HOW TO INITIALIZE THE BLU-RAY DISC HOME THEATER To put the program back at the factory-default, initialize the BD player as the following procedure. 1. Turn the power on. 2. Remove the disc on the tray and close the tray. 3.
FIRMWARE RENEWAL MODE Note: The file extension of the available firmware is The appearance shown in (*1) of Fig. c is described as “b30”. follows: 1. Turn the power on and remove the disc on the tray Appearance State and close the tray. Now Loading...
Page 17
How to Verify the Firmware Version 1. Turn the power on. 2. Remove the disc on the tray and close the tray. 3. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. h appears on the screen. All VFD lights. "...
Page 18
FIRMWARE RENEWAL MODE (for User) 1. Press [SETUP] button to display Setup menu. 6. Firmware loading starts. Fig. f will appear on the screen and Fig. g appears on the VFD. 2. Select Custom - Others - Software Update - Disc Update.
TROUBLESHOOTING FLOW CHART NO.1 The power cannot be turned on. See FLOW CHART No.2 <The fuse blows out.> Is the fuse normal? Is normal state restored when once unplugged Check for lead or short-circuiting of primary power cord is plugged again after several seconds. circuit component and replace AMP/PSU CBA if defective.
Page 20
FLOW CHART NO.4 Audio does not appear normally. Set the disc on the disc tray, and playback. Are the audio signals(serial data) outputted to Replace BD Main CBA & BD MECHANISM Pin(3, 4, 5, 6) of CN201? ASSEMBLY. Replace AMP/PSU CBA. 1-8-2 E1T12TR...
INTERNET RADIO (vTuner) ERROR CODE Error Code appears in the error screen when the unit “Summary Error Code” are shown in the list below. detects an error, as shown below. The code is used to Summary specifically determine the cause of error. Error message Error Code Network Error...
Page 22
Detailed Error Code table (vTuner – HTTP Status Code) Status Code Description 201 Created A new resource was created by this unit’s request. 202 Accepted This unit’s request was accepted but its processing is not completed. 204 No Content Though the server processed the request, there was no content. This unit caches latest resource and the requested resource is not modified.
Page 23
Status Code Description 703 URL Error The URL which this unit specified is in invalid form. Connection with the proxy which exists between this unit and the server or the 705 Connect Failed broadcast has failed. (IP conversion error) 706 Connect Failed Connection with the server or the broadcast has failed.
SCHEMATIC DIAGRAMS AND CBA Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 26
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED.
Page 27
AMP/PSU 1 Schematic Diagram CJS012201-0010 ( TO AV CBA CN403 ) GND TO GND PART EMC USE CN202 JK401A R5014 C5099 C5101 R5016 R5017 C5102 C5103 R5018 R5019 C5104 C5106 R5021 R5022 C5107 C5108 R5023 R5024 C5109 C5111 R5026 R5027 C5112 C5113 R5028...
Page 28
AMP/PSU 2 Schematic Diagram CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F9000) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
Page 40
AMP/PSU CBA Top View CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F9000) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
Page 41
AMP/PSU CBA Bottom View CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F9000) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
2L008 2L006 2L022 AV CBA 2L008 2L005 2L007 2L002 2L004 SD Card CBA AMP/PSU CBA 2L023 Power SW CBA 2L024 2L031 2L030 Front CBA 2L030 See Electrical Parts List MP3 CBA for parts with this mark. 2L030 HT2-M200(E1T12ED) 1-14-1 E1T12_13CEX...
Page 51
Packing HT2-M200(E1T12ED) X20-A X20-B X20-C X20-D S1-A S1-B Some Ref. Numbers are not in sequence. 1-14-2 E1T12_13PEX...
X20-A! A OWNERS MANUAL(EN) E1T12ED 1VMN29873 X20-A! B OWNERS MANUAL(FR) E1T13ED 1VMN30013 Model Mark X20-B! A OWNERS MANUAL(DE) E1T12ED 1VMN29893 HT2-M200(E1T12ED) X20-B! B OWNERS MANUAL(IT) E1T13ED 1VMN30014 HT2-M200(E1T13ED) X20-C! A OWNERS MANUAL(PL) E1T12ED 1VMN29894 X20-C! B OWNERS MANUAL(ES) E1T13ED 1VMN30015...
ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. ! have special characteristics important to safety. C3005 CHIP CERAMIC CAP . CH J 27pF/50V CHD1JJ3CH270 Before replacing any of these components, read C3006 CHIP CERAMIC CAP . CH J 27pF/50V CHD1JJ3CH270 carefully the product safety notice in this service C3008...
Page 54
Ref. No. Description Part No. RES CHIP 1608 1/10W J 100 Ω RRXA101YF002 CHIP RES. 1/10W J 100 Ω or R3021 RRXAJR5Z0101 RES CHIP 1608 1/10W J 100 Ω RRXA101YF002 CHIP RES. 1/10W J 100 Ω or R3022 RRXAJR5Z0101 RES CHIP 1608 1/10W J 100 Ω RRXA101YF002 CHIP RES.(1608) 1/10W 0 Ω...