Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D'INSTRUCTIONS
COLOUR CCD Camera
CCD-Farbkamera
Caméra CCD COULEUR
About this manual
Before installing and using the
•
camera, please read this manual
carefully. Be sure to keep it handy for
later reference.
À propos de ce manuel
Avant d'installer et d'utiliser la caméra,
•
veuillez lire ce manuel attentivement.
Gardez-le à portée de main pour toute
référence ultérieure.
VCC-5972P
Über diese Bedienungsanleitung
Lesen Sie bitte vor der Montage und
•
dem Inbetriebnehmen der Kamera
zuerst diese Bedienungsanleitung
sorgfältig durch und bewahren Sie sie
zum späteren Nachschlagen auf.
Advertisement
Chapters
Table of Contents
Related Manuals for Sanyo VCC-5972P
Summary of Contents for Sanyo VCC-5972P
- Page 1 VCC-5972P INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS COLOUR CCD Camera CCD-Farbkamera Caméra CCD COULEUR About this manual Über diese Bedienungsanleitung Before installing and using the Lesen Sie bitte vor der Montage und • • camera, please read this manual dem Inbetriebnehmen der Kamera carefully.
-
Page 2: Table Of Contents
Depending on the conditions of use, FEATURES installation and environment, please be sure to make the appropriate settings and • Built-in interline transfer method 1/3" CCD, adjustments. If you need help with installation approx. 470,000 picture elements and/or settings, please consult your dealer. •... -
Page 3: Precautions
For Install where the temperature range will stay internal settings and repairs, consult your between –10˚C and 50˚C. dealer (or a Sanyo Authorized Service Centre). (no condensation) Do not put objects inside the unit Cleaning Make sure that no metal objects or flammable •... -
Page 4: Parts Names
PARTS NAMES Lens iris output connector (4 pin) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. Auto white balance push lock button (AWB LOCK) Menu setting button (SET) Connect the camera to the monitor, then press the SET button for about 3 seconds to display the on-screen menu. - Page 5 Camera setup section (under the cover) This unit factory settings are as indicated below. These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS").
- Page 6 PARTS NAMES Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. Y/C OUT connector Using a coaxial cable (twin type, 75 ohms), connect the Y/C OUT connector from the camera to the S-VIDEO input terminal on the monitor or time lapse VCR.
-
Page 7: Mounting The Lens
Flange-back adjustment If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. Using a + screwdriver, loosen the FLANGE BACK LOCK screw (M2:+). - Page 8 MOUNTING THE LENS Installation of a VIDEO type auto-iris lens (sold separately) 2 (A) A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit that uses the video signal and a DC power source. Remove the lens mount cap. Attach the supplied C mount adaptor (A) to the auto-iris lens (B), then install the assembly on the camera.
-
Page 9: Connections
Compatible auto-iris lenses 1/3 inch Sanyo DC type lens 1/2 or 2/3 inch VIDEO type lens VCL-CS8LY: Standard angle, f= 8 mm Standard angle, f= 9 mm VCL-CS4LY: Wide angle, f= 4 mm Telephoto angle, f= 12 mm VCL-CS2LY: Ultra-wide angle, f= 2.8 mm... -
Page 10: Settings
SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. Depending on the camera installation location and conditions of use, it may be necessary to select other settings, without having to make adjustments. The selected settings can be confirmed using the on-screen menu. - Page 11 Automatic Gain Control (AGC) setting The automatic gain control can be turned ON or OFF using the AGC ON/OFF switch (6) in the camera setup section. ON: Auto gain control function on (setting used under normal conditions) (see page 21). GAMMA: ON (0.45), OFF (1) AGC GAIN: NORMAL (30 dB), HIGH (36 dB) OFF: Fixed gain...
- Page 12 SETTINGS Backlight compensation (BLC) setting The backlight compensation ON/OFF is set using the BLC ON/OFF switch (9) in the camera setup section. ON: Default setting, backlight compensation function on. However, depending on the camera installation location and conditions of use, if the backlight compensation function need to be set, with the BLC switch set to ON, press the SET button to select one of PRESET (1, 2) or W0=1...
-
Page 13: Using The On-Screen Menus
USING THE ON-SCREEN MENUS (Menu 1) (Menu 2) MENU FOR ADJUSTMENT MENU FOR ADJUSTMENT CAMERA ID SYNC IRIS APERTURE WHITE BALANCE SHUTTER WRITE PROTECT WRITE PROTECT PREVIOUS PAGE NEXT PAGE To display the menu Press the SET button for about 3 seconds. The “MENU FOR ADJUSTMENT”... -
Page 14: Adjustments
ADJUSTMENTS To enter settings or adjustments for the camera it must be connected to a monitor. The settings and adjustments are made (Menu 1) by ways of on-screen displays. MENU FOR ADJUSTMENT SYNC Concerning the WRITE PROTECT function IRIS In order to protect the settings and adjustments the WRITE WHITE BALANCE PROTECT function is set to ON. -
Page 15: Sync
1. SYNC 1-1. VBS phase adjustment Connect a VBS signal source to the VBS IN connector on the camera. The on-screen setting will automatically switch to VBS. Press the CURSOR (j or l) button to select the on-screen VBS setting (get it flashing), then press the SET button. -
Page 16: Iris
ADJUSTMENTS 2. IRIS 2-1. Auto-iris level adjustment Set the IRIS switch (10) to AI. The on-screen setting will automatically switch to AI. Press the CURSOR (j or l) button to select the on-screen AI setting (get it flashing), then press the SET button. The adjustment sub-menu “ADJUSTMENT FOR AI”... -
Page 17: Blc
3. BLC 3-1. Setting the light measuring area characteristics (size, position and distribution) for the MANUAL 1 setting Set the BLC switch (9) to ON. The on-screen setting for BLC will automatically switch to ON. Press the CURSOR (j or l) button to select the on-screen ON setting (get it flashing), then press the SET button. - Page 18 ADJUSTMENTS Press the CURSOR (j or l) button to select the desired window (get its value flashing), then press the CURSOR (d or c) button to set the desired value (maximum 15) for each of the 4 windows 0, 1, 2 and 3. Example: W0 : 5, W1 : 5, W2 : 10 and W3 : 10 WINDOW WEIGHTING WINDOW WEIGHTING...
-
Page 19: Blc Level Adjustment For The Preset 1 Setting
3-2. BLC level adjustment for the PRESET 1 setting Set the BLC switch (9) to ON. The on-screen setting for BLC will automatically switch to ON. Press the CURSOR (j or l) button to select the on-screen ON setting (get it flashing), then press the SET button. -
Page 20: White Balance
ADJUSTMENTS 4. WHITE BALANCE 4-1. PRESET MODE 2 (indoors, fluorescent lighting) setting adjustment Set the WB switches to the PRESET mode (switch 7 to OFF and switch 8 to ON). The on-screen setting for WHITE BALANCE will automatically switch to PRESET. Press the CURSOR (j or l) button to select the on-screen PRESET setting (get it flashing), then press the SET button. -
Page 21: Manual Setting Adjustment
4-2. MANUAL setting adjustment Set the WB switches to the MANUAL mode (both switches 7 and 8 to OFF). The on-screen setting for WHITE BALANCE will automatically switch to MANUAL. Press the CURSOR (j or l) button to select the on-screen MANUAL setting (get it flashing), then press the SET button. -
Page 22: Agc
ADJUSTMENTS 5. AGC Set the AGC switch (6) to ON. The on-screen setting for AGC will automatically switch to ON. Press the CURSOR (j or l) button to select the on-screen ON setting (get it flashing), then press the SET button. -
Page 23: Camera Id
6. CAMERA ID Press the CURSOR (j or l) button to select NEXT PAGE (get it flashing), then press the SET button. The second page of the “MENU FOR ADJUSTMENT” will be displayed. (Refer to page 12.) CURSOR SHUTTER MENU FOR ADJUSTMENT WRITE PROTECT CAMERA ID APERTURE... -
Page 24: Aperture
ADJUSTMENTS 7. APERTURE Press the CURSOR (j or l) button to select NEXT PAGE (get it flashing), then press the SET button. The second page of the “MENU FOR ADJUSTMENT” will be displayed. CURSOR SHUTTER MENU FOR ADJUSTMENT WRITE PROTECT CAMERA ID APERTURE NEXT PAGE... -
Page 25: Troubleshooting
TROUBLESHOOTING Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen •... -
Page 26: Menu Display
MENU DISPLAY b SYNC ADJUSTMENT SW4: INT (input VBS signal) (input VS signal) MENU FOR ADJUSTMENT SYNC b IRIS ADJUSTMENT IRIS SW10: AI/EI WHITE BALANCE ADJUSTMENT FOR AI SHUTTER (IRIS LEVEL) WRITE PROTECT o------z------p 23 NEXT PAGE b BLC ADJUSTMENT SW9: ON/OFF MENU FOR ADJUSTMENT CAMERA ID... - Page 27 ADJUSTMENT FOR VS ADJUSTMENT FOR VBS (H SYNC PHASE) (PHASE) o------z------p 280 H o------z------p 280 SC o------z------p 90 ADJUSTMENT FOR BLC ADJUSTMENT FOR BLC (SIZE) BLC MODE PRESET1 PRESET2 MANUAL1 BLC LEVEL MANUAL2 ADJUSTMENT FOR BLC ADJUSTMENT FOR BLC (BLC LEVEL) (POSITION) o------z------p 15 (OFFSET)
-
Page 28: Specifications
SPECIFICATIONS Camera: Scaning system : PAL standard (625 TV lines, 25 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image device CCD Picture elements : 795 (H) x 596 (V) Effective picture elements : 752 (H) x 582 (V) Synchronizing system : Internal sync/External sync External sync : VBS or VS signal (Genlock, Automatic switching) Resolution : 460 TV lines horizontally, 400 TV lines vertically... - Page 29 Dimensions: mm 108.5 99.5 1/4”–20 UNC Approx. 1.8 m Approx. 1.8 m : mm Features and specifications are subject to change without prior notice or obligations. English...