Ryobi RPW3200 Operator's Manual page 11

Do not use this product if any parts on the Packing
List are already assembled to your product when you
unpack it. Parts on this list are not assembled to the
product by the manufacturer and require customer
installation. Use of a product that may have been
improperly assembled could result in serious personal
injury.
NOTE: This tool is heavy. To avoid back injury, lift with
your legs, not your back, and get help when needed.
■ Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
■ Do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
PACKING LIST
– Pressure Washer
– 7.6m (25 ft.) High Pressure Hose
– Trigger Handle Holder
– Trigger Handle
– Screw (1/4-20 x 1.77 in., T30 Torx head) x2
– Screw (1/4-20 x 2.0 in., T30 Torx head)
– Flat Washer
– Hex nut (1/4-20 in.) x3
– Spray Wand
– 5-in-1 Change Over Nozzle
– 4-Cycle Engine Lubricant (SAE 30 or SAE 10W30)
– Hose Storage
– Operator's Manual
TOOLS NEEDED
The following tools (not included or drawn to scale) are
needed for assembly:
– 7/16 in. wrench
– T30 head screwdriver
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
Do not attempt to modify this product or create
accessories not recommended for use with this product.
Any such alteration or modification is misuse and could
result in a hazardous condition leading to possible
serious personal injury.
WARNING
WARNING
WARNING
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark
plug wire from the spark plug when assembling parts.
RAISING AND LOWERING THE HANDLE
See figure 2.
■ To raise the handle (for moving the pressure washer):
pull the handle up until the handle release knob snaps
into locking position. Ensure the lock is secured in the
frame hole before moving.
■ To lower the handle (for storing or transporting the
pressure washer): pull the handle release knob out
and lower the handle to the down position.
NOTE: The handle can not be locked in the down
position.
Never use the handle to lift the pressure washer. The
handle should only be used for moving the unit by rolling
it on its wheels.
INSTALLING HOSE STORAGE, TRIGGER HANDLE
HOLDER, AND SPRAY WAND HOLDER
See figures 3 - 4.
■ Raise handle as described in the Raising and Lowering
Handle section.
■ Place hose storage onto the handle as shown.
■ Align the holes in the hose storage with the holes in
the handle.
■ Insert screw (1/4-20 x 1.77 in.) through the holes in the
left side of the handle and hose storage.
■ Place nut onto bolt and tighten.
■ Place the trigger handle holder onto the handle as
shown.
■ Align the holes in the trigger handle holder with the
holes in the hose storage and the handle.
■ Insert screw (1/4-20 x 2.0 in.) through the holes in
handle, hose storage, and trigger handle holder.
■ Turn bolt while holding the nut in place to tighten and
secure.
■ Place spray wand holder onto pressure washer frame.
■ Align the holes in the spray wand holder with the holes
in the pressure washer frame.
■ Insert screw (1/4-20 x 1.77 in.) through the holes in
the spray wand holder and the pressure washer frame.
■ Place nut onto screw and tighten.
ASSEMBLING THE SPRAY WAND TO THE TRIGGER
HANDLE
See figure 5.
■ Place the threaded end of the spray wand in the
5
WARNING