CENTRAL SERVICE CENTER 16. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove 10. Service technicians should remove their the instrument's ground lead last. watches while repairing an MWO. Samsung Electronics...
Page 3
(Use a screwdriver.) 3. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. Fig. 1-1. Discharging the High Voltage Capacitor Samsung Electronics...
2. Specifications 2-1 Table of Specifications TIMER 99Mins POWER LEVEL ON TIME OFF TIME POWER SOURCE 230V 50Hz, AC CE979GSE POWER CONSUMPTION MICROWAVE : 1,500W 4 sec 26 sec MAX : 1,500W 170W 7 sec 23 sec GRILL : 1,300W...
11. When removing the magnetron, make sure that its antenna does not hit any adjacent parts. Magnetron Fan Motor 12. When replacing the magnetron, be sure to remount the magnetron gasket in the correct position, and make sure the gasket is in good condition. Samsung Electronics...
Page 7
HINGE VOLT interlock switch and the interlock monitor switch. 3. Microwave emission should not exceed 5§ /§† (All service adjustments should be HINGE UPPER made for minimum RF emission.) HINGE VOLT Samsung Electronics...
Page 8
Reconnect all the leads to the elevation motor. Screw the elevation motor cover to the base plate with screw driver. 10. Remount the coupler in the correct position. SCREW ELEVATION MOTOR TANTABLE MOTOR WEIGHT SENSOR SCREW Samsung Electronics...
Page 9
"ALIGNMENT AND ADJUSTMENTS" on page 5-2(whenever they are repaired or replaced). Door Sensing S/W Interlock Switch Replacement When replacing defective switches, be sure to check that the mointing tabs are not bent or Body Latch broken. Samsung Electronics...
4-12 Replacement of Gas Sensor and ThermoSwitch 1. Disconnect all lead wires from the gas sensor thermostat and the thermostat. 2. Remove screws securing the air guide. Gas sensor Samsung Electronics...
3. Before touching any oven components or wiring, always unplug the oven and discharge the high voltage capacitor. 5-1 High Voltage Transformer 1. Remove connectors from the transformer terminals Filament Terminals and check continuity. 2. Normal resistance readings are as follows: MODEL CE979GSE Secondary Approx. 96Ω Filament Approx.0Ω Primary Approx.1.6Ω...
5. Confirm that the gap between the switch Door Open Door Closed housing and the switch actuator is no more than ∞ Primary switch 0.5mm when door is closed. ∞ Monitor switch (COM-NC) ∞ Monitor switch (COM-NO) ∞ Door Sensing S/W Samsung Electronics...
Page 13
5. After heating for 2 minutes, measure the water temperature in each beaker. 6. Microwave heat distribution rate can be calculated as follows: Minimum Beaker Temperature Rise Heat Distribution = X 100(%) Maximum Temperature Rise The result should exceed 65%. Cooking Tray Samsung Electronics...
2 inches to any metal (otherwise, erroneous readings readings will result). 5. The measured leakage must be less than 5mW/cm WARNING AVOID TOUC HING THE HIGH VOLTAGE COMPONENTS. Samsung Electronics...
Page 15
3. At least once a year have the Microwave Energy Survey Meter checked for accuracy by its manufacturer. Samsung Electronics...
Low to "Full" power. One complete ON/OFF cycle of the power control is 30 seconds. 8. The cooking when the oven is set at any power setting is shown on the display (starts to count down.) Samsung Electronics...
Page 17
The time of day reappears on the display window. 2. The oven lamp and cooking indicators turn off. 3. The fan motor stops. 4. The power control relay turns off to cutting the primary voltage to the high voltage transformer (This stops magnetron oscillation). Samsung Electronics...
The output frequency of the basic condition (when 0 point adjusted) is between 3150 and 3650Hz. The weight sensor converts the weight of the food into a series of pulses that are compared to the"zero point" wavefrom. This frequency difference determines the cooking time. Samsung Electronics...
Page 19
10minutes. (When cooking food that weight less tman 300g the maximum time is 10 minutes.) No tray (Occurs if oven is Install the rotating dish operated without the rotating dish.) Problen with the EEPROM Replace the PCB assy Samsung Electronics...
Page 20
Otherwise use a tool (such as long nose pliers) 4. If you remove the tie during servicing, do not damage the wire. Adjust and arrange the wire and tie(heat proof onsulated tie) after the repairs have been completed. Samsung Electronics...
Page 21
The water temperature should be about 80° Inspection of grill cooking a. Put the applicable " cooker" for grill cooking inside b. Do the following grill ¡ time setting 5 minutes ¡ start cooking. c. Normal : The seize heater is red. Samsung Electronics...
Page 22
Is the LVT wire normal? Exchange/adjustment Elevation a.Check the connections to Poor wire connection Adjustment action the elevation assembly unsatisfactor b. Continuity between terminals Disconnection Exchange/ of the elevation motor Assembly exchange (Measure after removing the power leads) Samsung Electronics...
Page 23
Continuity of high voltage diode Forward direction (Measure it after cutting the =about 0§ power leads). d. Continuity between the magnetron Reverse direction =500§ e. High frequency emissions Bad continuity Bad magnetron f. Power relay operation Bad contact points Samsung Electronics...
Page 24
Rotate the fan by hand cleaning or exchange Poor defrosting a. Check the connections to Poor connection Adjustment the weight sensor b. Readjust the 0 point 0 point not adjusted Taking measures according to the error list. Samsung Electronics...
Page 25
Explain to the customer that he following are Check the continuity dancerous hazards : to ground. a. Connection to the gas pipe b. Connection to the vinyl water pipe c. Connection to the telephone line. Samsung Electronics...
3 . LAMP : ON L.V.T WEIGHT PRIMARY LATCH S/W MONITOR S/W DOOR SENSING S/W ELEVATION DOOR SENSOR SWITCH SWITCH (ASSY MAIN P.C.B) MAGNETRON HIGH VOLTAGE DIODE TO CHASSIS HIGH VOLTAGE CAPACITOR H.V.FUSE SYMBOL COLOR ORANGE BROWN BLUE HIGH VOLTAGE TRANSFORMER Samsung Electronics 10-1...