Advertisement
Quick Links
Cordless Circular Saw
Blade
diameter
85
mm
(3-3/8")
MODEL 5091DZ
85
mm
(3-3/8")
MODEL 5091DWH
85
mm
(3-3/8")
MODEL 5091DWG
Without Battery or Charger
85
mm
(3-3/8")
MODEL 5091D
With Battery Cartridge and Fast Charger
No load speed
Overall
Net
Cutting depth
900
450
(RPM)
1
length
1
weight
Vith Battery Cartridge
INSTRUCTION MANUAL
85
mm
(3-3/8")
SPECIFICATIONS
0
-
24.5
mm
0
-
18"
316 m m
1.9
kg
(0
-
15/16")
(0
~
11/16")
(12.112")
(4.2
Ibs)
1,000
Model 5091D
Battery Cartridge 1201
I
1201A
Model DC1201 Fast Charger
12
v
Voltage
I
Input
I
output
I
Charging time
A.C. only 60 Hz
D.C.
7.2
V
-
12
V
1
Hr.
Advertisement
Related Manuals for Makita 5091DWG
Summary of Contents for Makita 5091DWG
- Page 1 (3-3/8") With Battery Cartridge and Fast Charger No load speed (RPM) 18" 1,000 11/16") Model DC1201 Fast Charger Input A.C. only 60 Hz D.C. MODEL 5091DWH MODEL 5091DWG Overall length weight 316 m m (12.112") (4.2 Ibs) output Charging time...
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16.
- Page 4 Before using battery charger, read all instructions and cautionary markings battery charger, CAUTION To reduce risk of injury, charge only MAKITA Battery Cartridge 7000, 7001, 9000, 9001, 9100, 9101, 9101A, 1200, 1201, 1201A, 1210 & 1211.
- Page 5 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or receptacle. Do not allow anything t o cover or clog the charger vents. 4.
-
Page 6: Additional Safety Rules
ADDITIONAL SAFETY RULES 1. Be aware that this tool is always in an operating condition, because not have t o be plugged into an electrical outlet. 2. Wear hearing protection. Keep Guards In Place and In Working Order. Never wedge or tie lower guard open. Check operation of lower guard before each use. - Page 7 NEVER place your hand or fingers behind the saw. If kickback occurs, the saw could easily jump backwards over your hand, possibly causing severe injury. Lower Guard. Raise lower guard with the retracting handle. Adjustments. Before cutting be sure depth and bevel adjustments are tight. 12.
- Page 8 15. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way t o cut off the end of a board, and Fig.
- Page 9 Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool.
- Page 10 Then remove the bolt, outer flange and blade. specifically designed t o charge only couple of times. blade Makita battery charg- or the battery...
- Page 11 CAUTION : Be sure the blade is installed with teeth pointing up a t the front of the tool. Use only the Makita hex wrench to install or remove the blade. Hex wrench storage When not in use, the hex wrench can be convenient I stored.
- Page 12 Adjusting the depth of cut Loosen the screw on the depth guide and move the base up or down. You can read the depth of cut by aligning the top of the notch in the depth guide with the graduations on right side.
- Page 13 Sighting The front of the base i s notched to provide two guide edges. For straight cuts, align the edge with engraved on with your cutting line on the workpiece. For 45' bevel cuts, align the edge with 45' engraved on it with your cutting line. Switch action To prevent the trigger from being acciden- tally pulled, a lock-off lever i s provided.
-
Page 14: Maintenance
Always be sure that the tool is switched off and the battery cartridge i s removed before attempting ot perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Clamp screw Fig. -
Page 15: Optional Accessories
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in manual. - Page 16 Mar,-30-'95 (3-3/8") CORDLESS CIRCULAR SAW Model 5091D Note: The switch and other part configurations may differ from country to country.
- Page 17 Inner Flange 28 Retaining Ring Cover Salety Flat Washer 30 Tapping Screw 4x18 Bearing Box Tension Spring Makita Label Blade Case Tapping Screw 4x18 Housing Set (With Item Compression Spring 7 Plane Bearing 4 Gear Complete Thin Washer 4 Plane Bearing...
- Page 18 “Tools-Electric’ MAKITA Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.