Page 1 Patriot 2 0 1 5 O W N E R ’ S M A N U A L I n f o r ma t i o n P r o v i d e d b y :...
Page 2 Driving after drinking can lead to an accident. Your perceptions are less sharp, your reflexes are Jeep is a registered trademark of FCA US LLC slower, and your judgment is impaired when you have been drinking. Never drink and then drive.
Page 3: Introduction 3
TABLE OF CONTENTS SECTION PAGE INTRODUCTION ............. . . 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE .
Page 4 I n f o r ma t i o n P r o v i d e d b y :...
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....7 ROLLOVER WARNING .
Page 6: Introduction
4 INTRODUCTION When it comes to service, remember that your authorized INTRODUCTION dealer knows your vehicle best, has factory-trained tech- Congratulations on selecting your new FCA US LLC nicians and genuine parts, and cares about your satisfac- vehicle. Be assured that it represents precision workman- tion.
Page 7: How To Use This Manual
INTRODUCTION 5 control. Failure to operate this vehicle safely may result seat belts could cut the highway death toll by 10,000 or in a collision, rollover of the vehicle, and severe or fatal more each year and could reduce disabling injuries by injury.
Page 8 6 INTRODUCTION I n f o r ma t i o n P r o v i d e d b y :...
Page 9: Warnings And Cautions
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire Owner’s Manual, you may miss important information.
Page 10: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death. Right Front Body VIN Location NOTE: It is illegal to remove or alter the VIN. I n f o r ma t i o n P r o v i d e d b y :...
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A WORD ABOUT YOUR KEYS ... . .12 ▫ Rearming The System ....19 ▫...
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Sound Horn With Remote Key Lock ..22 POWER WINDOWS — IF EQUIPPED ..35 ▫ Flash Lights With Remote Key Lock/Unlock . . .23 ▫...
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 SAFETY TIPS ......100 ▫ Safety Checks You Should Make Inside The Vehicle .
Page 14: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The authorized dealer that sold you your new vehicle has 1. Place the shift lever in PARK (if equipped with an the key code numbers for your vehicle locks. These automatic transmission).
Page 15 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in PARK, rotate the key clockwise slightly, and then remove the key as described above.
Page 16: Locking Doors With A Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locking Doors With A Key WARNING! (Continued) You can insert the key with either side up. To lock the • Allowing children to be in a vehicle unattended is door, turn the key to the right. To unlock the door, turn dangerous for a number of reasons.
Page 17: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 During normal operation, after turning on the ignition SENTRY KEY® switch, the Vehicle Security Light will turn on for three The Sentry Key® Immobilizer System prevents unau- seconds for a bulb check. If the light remains on after the thorized vehicle operation by disabling the engine.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! CAUTION! The Sentry Key® Immobilizer system is not compat- Always remove the Sentry Keys® from the vehicle ible with some aftermarket remote starting systems. and lock all doors when leaving the vehicle unat- Use of these systems may result in vehicle starting tended.
Page 19: Customer Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 4. Insert a blank Sentry Key® into the ignition switch. Customer Key Programming Turn the ignition switch to the ON/RUN position If you have two valid Sentry Keys®, you can program within 60 seconds. After 10 seconds, a single chime new Sentry Keys®...
Page 20: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized NOTE: Changes or modifications not expressly approved dealer to have all remaining keys erased from the sys- by the party responsible for compliance could void the tem’s memory.
Page 21: To Arm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Arm The System Rearming The System If something triggers the alarm, and no action is taken to 1. Remove the key from the ignition switch and get out disarm it, the Vehicle Security Alarm will turn off the of the vehicle.
Page 22: Vehicle Security Alarm Manual Override
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE once the Vehicle Security Alarm is armed (after 16 seconds), when you pull the door handle to exit, the alarm will sound. If this occurs, push the UNLOCK button on the RKE transmitter to disarm the Vehicle Security Alarm.
Page 23: To Unlock The Doors And Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • For vehicles not equipped with the EVIC, perform the To Unlock The Doors And Liftgate following steps: Push and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door or twice 1.
Page 24: Illuminated Approach - If Equipped
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pushing the LOCK button on the RKE transmitter To Lock The Doors And Liftgate while you are inside the vehicle will activate the Vehicle Push and release the LOCK button on the RKE transmit- Security Alarm.
Page 25: Flash Lights With Remote Key Lock/Unlock
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, perform the NOTE: Pushing the LOCK button on the RKE transmitter following steps: while you are in the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security 1.
Page 26: Using The Panic Alarm
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the NOTE: Pushing the LOCK button on the RKE transmitter following steps: while you are in the vehicle will activate the Vehicle Security Alarm. Opening a door with the Vehicle Security 1.
Page 27: Programming Additional Transmitters
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 NOTE: When you turn off the Panic Alarm by pushing two halves of the RKE transmitter apart. Make sure the PANIC button a second time, you may have to move not to damage the elastomer seal during removal. closer to the vehicle due to the radio frequency noises of the system.
Page 28: General Information
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To reassemble the RKE transmitter case, snap the two If your RKE transmitter fails to operate from a normal halves together. distance, check for these two conditions: NOTE: If the RKE transmitter is equipped with a screw, 1.
Page 29: How To Use Remote Start
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 NOTE: • Battery at an acceptable charge level • The vehicle must be equipped with an automatic • RKE PANIC button not pushed transmission to be equipped with Remote Start. • System not disabled from previous remote start event •...
Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Abort Message On Electronic Vehicle To Enter Remote Start Information Center (EVIC) — If Equipped The following messages will display in the EVIC if the Push and release the REMOTE START button vehicle fails to remote start or exits remote start prema- on the RKE transmitter twice within five sec- turely:...
Page 31: To Exit Remote Start Without Driving
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 • The engine can be started two consecutive times (two To Exit Remote Start Mode Without Driving The 15-minute cycles) with the RKE transmitter. However, Vehicle the ignition switch must be cycled to the ON/RUN Push and release the REMOTE START button one time or position before you can repeat the start sequence for a allow the engine to run for the entire 15-minute cycle.
Page 32: Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS WARNING! Manual Door Locks • For personal security and safety in the event of an Use the manual door lock knob to lock the doors from collision, lock the vehicle doors as you drive as inside the vehicle.
Page 33: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power Door Locks A power door lock switch is located on the driver’s and front passenger’s door panel.
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Lock Doors — If Equipped 2. Within 15 seconds, cycle the ignition switch be- tween LOCK and ON/RUN and then back to The auto door lock feature default condition is enabled. LOCK four times, ending up in the LOCK position When enabled, the door locks will lock automatically (do not start the engine).
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Automatic Unlock Doors On Exit Equipped/Personal Settings (Customer- Programmable Features)” in “Understanding Your In- The doors will unlock automatically if: strument Panel” for further information. • The Automatic Unlock Doors On Exit feature is en- •...
Page 36: Child-Protection Door Lock System - Rear Doors
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: 3. Repeat steps 1 and 2 for the opposite rear door. • If you do not hear the chime, it means that the system did not enter the programming mode and you will need to repeat the procedure.
Page 37: Power Windows - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 NOTE: For emergency exit with the system engaged, move the lock knob up (unlocked position), roll down the window, and open the door with the outside door handle. POWER WINDOWS — IF EQUIPPED Power Window Switches The window controls on the driver’s door trim panel control all the door windows.
Page 38 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: WARNING! • For vehicles not equipped with the Electronic Vehicle Never leave children unattended in a vehicle, and do Information Center (EVIC), the power window not let children play with power windows. Do not switches will remain active for 45 seconds after the leave the Key Fob in or near the vehicle, or in a ignition switch is turned to the LOCK position.
Page 39: Auto-Down
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Auto-Down The driver’s door window switch has an Auto-Down feature. Push the window switch past the first detent, release, and the window will go down automatically. To cancel the Auto-Down movement, operate the switch in either the up or down direction and release the switch.
Page 40: Window Lockout Switch
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Lockout Switch The window lockout switch on the driver’s door allows you to disable the window controls on the rear passenger doors. To disable the window controls on the rear pas- senger doors, push the window LOCKOUT switch.
Page 41: Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 LIFTGATE NOTE: The key that is used to start the vehicle is also used to lock or unlock the doors and open the liftgate. To unlock the liftgate, insert the key into the lock and turn to the right (manual lock models only).
Page 42: Occupant Restraint Systems
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINT SYSTEMS WARNING! Some of the most important safety features in your • Driving with the liftgate open can allow poisonous vehicle are the restraint systems: exhaust gases into your vehicle. You and your •...
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Here are some simple steps you can take to minimize the 5. You should read the instructions provided with your risk of harm from a deploying air bag: child restraint to make sure that you are using it properly.
Page 44: Seat Belt Systems
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ejection and the risk of injury caused by striking the WARNING! inside of the vehicle. Everyone in a motor vehicle should be belted at all times. • Never place a rear-facing child restraint in front of an air bag.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 After the sequence completes, the Seat Belt Reminder NOTE: If BeltAlert has been deactivated, the Seat Belt Light remains illuminated until the respective seat belts Reminder Light will continue to illuminate while the are buckled.
Page 46 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not allow people to ride in any area of your • Relying on the air bags alone could lead to more vehicle that is not equipped with seats and seat severe injuries in a collision.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! (Continued) WARNING! (Continued) • A lap belt worn too high can increase the risk of • A seat belt that is too loose will not protect you injury in a collision. The seat belt forces won’t be at properly.
Page 48 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front WARNING! (Continued) seat, and next to your arm in the rear seat (for vehicles • A shoulder belt placed behind you will not protect equipped with a rear seat).
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 3. When the seat belt is long enough to fit, insert the latch plate and pull on the lap belt. A snug seat belt reduces plate into the buckle until you hear a “click.” the risk of sliding under the seat belt in a collision.
Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the seat belt, push the red button on the 1. Remove the mini-latch and regular latch from its buckle. The seat belt will automatically retract to its stowed position in the right rear side trim panel. stowed position.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Routing The Rear Center Shoulder Belt Connecting Mini-Latch To Buckle I n f o r ma t i o n P r o v i d e d b y :...
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Center Seat Belt Buckled Detaching Mini-Latch And Buckle 2. Grasp the mini-latch plate and pull the seat belt over the seat. 3. Route the shoulder belt to the inside of the right head restraint.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 4. When the seat belt is long enough to fit, insert the 9. To release the seat belt, push the red button on the mini-latch plate into the mini-buckle until you hear a buckle.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Slide the latch plate upward over the folded webbing. WARNING! (Continued) The folded webbing must enter the slot at the top of • When reattaching the mini-latch and mini-buckle, the latch plate. ensure the seat belt webbing is not twisted.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 NOTE: The adjustable upper shoulder belt anchorage is equipped with an Easy Up feature. This feature allows the shoulder belt anchorage to be adjusted in the upward position without pushing or squeezing the release but- ton.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pregnant women should wear the lap part of the seat belt WARNING! across the thighs and as snug across the hips as possible. Keep the seat belt low so that it does not come across the •...
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 The pretensioners are triggered by the Occupant Re- manual for further information. The table below defines straint Controller (ORC). Like the air bags, the preten- the type of feature for each seating position. sioners are single use items.
Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the passenger seating position is equipped with an WARNING! ALR and is being used for normal usage, only pull the seat belt webbing out far enough to comfortably wrap • Never place a rear-facing child restraint in front of around the occupant’s mid-section so as to not activate an air bag.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 How To Disengage The Automatic Locking Mode WARNING! (Continued) Unbuckle the combination lap/shoulder belt and allow it • Do not use the Automatic Locking Mode to restrain to retract completely to disengage the Automatic Locking occupants who are wearing the seat belt or children Mode and activate the vehicle sensitive (emergency) who are using booster seats.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Active Head Restraints (AHR) Work The Occupant Restraint Controller (ORC) determines whether the severity, or type of rear impact will require the Active Head Restraints (AHR) to deploy. If a rear impact requires deployment, both the driver and front passenger seat AHRs will be deployed.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 1. Grasp the deployed AHR from the rear seat. WARNING! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a collision.
Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. Review Table Below A — Downward Movement B — Rearward Movement C — Final Downward Movement To Engage Locking Mechanism I n f o r ma t i o n P r o v i d e d b y :...
Page 63: Supplemental Restraint System (Srs)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 4. The AHR front soft foam and trim half should lock NOTE: into the back decorative plastic half. • If you have difficulties or problems resetting the Active Head Restraints, see an authorized dealer. •...
Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Advanced Front Air Bags • Supplemental Side Air Bags • Front and Side Impact Sensors • Seat Belt Pretenioners • Seat Belt Buckle Switch • Seat Track Position Sensors Advanced Front Air Bags This vehicle has Advanced Front Air Bags for both the driver and front passenger as a supplement to the seat Advanced Front Air Bag And Knee Impact Bolster...
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 output appropriate to the severity and type of collision as WARNING! determined by the Occupant Restraint Controller (ORC), which may receive information from the front impact • Being too close to the steering wheel or instrument sensors or other system components.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Relying on the air bags alone could lead to more • No objects should be placed over or near the air severe injuries in a collision. The air bags work bag on the instrument panel or steering wheel, with your seat belt to restrain you properly.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 On the other hand, depending on the type and location of way as the air bags inflate to their full size. The Advanced impact, Advanced Front Air Bags may deploy in crashes Front Air Bags fully inflate in less time than it takes to with little vehicle front-end damage but that produce a blink your eyes.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Air Bags Your vehicle is equipped with two types of side air bags: 1. Supplemental Seat-Mounted Side Air Bags (SABs): Located in the outboard side of the front seats. The SABs are marked with a SRS AIRBAG or AIRBAG label sewn into the outboard side of the seats.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 When the SAB deploys, it opens the seam on the out- 2. Supplemental Side Air Bag Inflatable Curtains board side of the seatback’s trim cover. The inflating SAB (SABICs): Located above the side windows. The trim deploys through the seat seam into the space between the covering the SABICs is labeled SRS AIRBAG or occupant and the door.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SABICs may help reduce the risk of head injury to front WARNING! and rear seat outboard occupants. SABICs may reduce the risk of injuries in certain side impact and vehicle • Your vehicle is equipped with left and right rollover events, in addition to the injury reduction poten- Supplemental Side Air Bag Inflatable Curtains tial provided by the seat belts and body structure.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 The SABICs and SABs (“Side Air Bags”) are designed to Seat belts (and child restraints where appropriate) are activate in certain side impacts and certain rollover necessary for your protection in all collisions. They also events.
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE deploys the left Side Air Bags only and a right side WARNING! (Continued) impact deploys the right Side Air Bags only. • Relying on the Side Air Bags alone could lead to The Side Air Bags will not deploy in all side collisions, more severe injuries in a collision.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 The Side Air Bags will not deploy in all rollover events. If you do have a collision, which deploys the air bags, any The rollover sensing-system determines if a rollover or all of the following may occur: event may be in progress and whether deployment is •...
Page 74 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE continues, see your doctor. If these particles settle on NOTE: your clothing, follow the garment manufacturer’s in- • Air bag covers may not be obvious in the interior trim, structions for cleaning. but they will open during air bag deployment.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 • Turn on the interior lights, which remain on as long as or ON/RUN position. If the ignition is in the OFF the battery has power or until the ignition is placed in position or in the ACC position, the air bag system is not the “OFF”...
Page 76 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE diagnostics also record the nature of the malfunction. WARNING! While the air bag system is designed to be maintenance free, if any of the following occurs, have an authorized Ignoring the Air Bag Warning Light in your instru- dealer service the air bag system immediately.
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or may • Modifications to any part of the air bag system not function properly if modifications are made.
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Event Data Recorder (EDR) These data can help provide a better understanding of the circumstances in which crashes and injuries occur. This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in NOTE: EDR data are recorded by your vehicle only if a certain crash or near crash-like situations, such as an air non-trivial crash situation occurs;...
Page 79: Child Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Child Restraints WARNING! Everyone in your vehicle needs to be buckled up at all In a collision, an unrestrained child can become a times, including babies and children. projectile inside the vehicle. The force required to Every state in the United States, and every Canadian hold even an infant on your lap could become so province, requires that small children ride in proper...
Page 80 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE There are different sizes and types of restraints for NOTE: children from newborn size to the child almost large • For additional information, refer to www.seatcheck.org enough for an adult seat belt. Always check the child seat or call 1–866–SEATCHECK (732–8243).
Page 81 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Infants and Children who are two years old or Either an Infant Carrier or a Convertible Toddlers younger and who have not reached the Child Restraint, facing rearward in the rear...
Page 82 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints WARNING! Safety experts recommend that children ride rear-facing • Never place a rear-facing child restraint in front of in the vehicle until they are two years old or until they an air bag.
Page 83 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Older Children And Child Restraints All children whose weight or height is above the forward-facing limit for the child seat should use a Children who are two years old or who have outgrown belt-positioning booster seat until the vehicle’s seat belts their rear-facing convertible child seat can ride forward- fit properly.
Page 84 82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • When your child restraint is not in use, secure it in • Improper installation can lead to failure of an the vehicle with the seat belt or LATCH anchor- infant or child restraint.
Page 85 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 2. Do the child’s knees bend comfortably over the front WARNING! of the vehicle seat – while they are still sitting all the way back? Never allow a child to put the shoulder belt under an arm or behind their back.
Page 86 84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints Restraint Type Combined Use any attachment method shown with an “X” Below Weight of the LATCH – Seat Belt Only LATCH – Seat Belt + Top Child + Child Lower Anchors Lower Anchors Tether Anchor...
Page 87 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Lower Anchors And Tethers For Children (LATCH) Your vehicle is equipped with the child restraint anchor- Restraint System age system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH- equipped child seats.
Page 88 86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle Lower Anchorage Symbol 2 anchorages per • seating position Top Tether Anchorage Symbol • I n f o r ma t i o n P r o v i d e d b y :...
Page 89 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 LATCH POSITION TABLE What is the weight limit (child’s weight + 65 lbs (29.5 kg) Use the LATCH anchorage system until weight of the child restraint) for using the the combined weight of the child and the LATCH anchorage system to attach the child restraint is 65 lbs (29.5 kg).
Page 90 88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH POSITION TABLE Can two child restraints be attached using Never “share” a LATCH anchorage with a common lower LATCH anchorage? two or more child restraints. If the center position does not have dedicated LATCH lower anchorages, use the seat belt to in- stall a child seat in the center position next to a child seat using the LATCH anchor-...
Page 91 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Locating LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 92 90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating Tether Anchorages There are tether strap anchorages behind each rear seating position located on the back of the seat. LATCH-compatible child restraint systems will be equipped with a rigid bar or a flexible strap on each side. Each will have a hook or connector to attach to the lower anchorage and a way to tighten the connection to the anchorage.
Page 93 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 restraints with flexible, webbing mounted lower attach- To Install A LATCH-Compatible Child Restraint ments can be installed in any rear seating position. If the selected seating position has a Switchable Auto- matic Locking Retractor (ALR) seat belt, stow the seat WARNING! belt, following the instructions below.
Page 94 92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seat Belt: restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position.
Page 95 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 Installing Child Restraints Using The Vehicle Seat WARNING! Belt • Improper installation of a child restraint to the The seat belts in the passenger seating positions are LATCH anchorages can lead to failure of the re- equipped with a Switchable Automatic Locking Retractor straint.
Page 96 94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle • ALR = Switchable Automatic Locking Retractor Top Tether Anchorage Symbol • I n f o r ma t i o n P r o v i d e d b y :...
Page 97 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 LAP/SHOULDER BELT SYSTEMS What is the weight limit (child’s Weight limit of the Always use the tether anchor when using the seat weight + weight of the child re- Child Restraint belt to install a forward facing child restraint, up to straint) for using the Tether Anchor the recommended weight limit of the child re- with the seat belt to attach a for-...
Page 98 96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing A Child Restraint With A Switchable 4. Pull on the webbing to make the lap portion tight Automatic Locking Retractor (ALR) against the child seat. 1. Place the child seat in the center of the seating 5.
Page 99 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 8. If the child restraint has a top tether strap and the Installing Child Restraints Using The Top Tether seating position has a top tether anchorage, connect Anchorage: the tether strap to the anchorage and tighten the tether strap.
Page 100 98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available.
Page 101: Transporting Pets
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine and • An incorrectly anchored tether strap could lead to drivetrain (transmission and axle) in your vehicle. increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
Page 102: Safety Tips
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! WARNING! Never use Non-Detergent Oil or Straight Mineral Oil • Do not leave children or animals inside parked in the engine or damage may result. vehicles in hot weather. Interior heat build-up may cause serious injury or death.
Page 103: Exhaust Gas
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Exhaust Gas WARNING! (Continued) • If it is necessary to sit in a parked vehicle with the WARNING! engine running, adjust your heating or cooling Exhaust gases can injure or kill. They contain carbon controls to force outside air into the vehicle.
Page 104: Safety Checks You Should Make Inside The Vehicle
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE not lit during starting, see your authorized dealer. If the Safety Checks You Should Make Inside The light stays on, flickers, or comes on while driving, have Vehicle the system checked by an authorized dealer. Seat Belts Defroster Inspect the seat belt system periodically, checking for...
Page 105 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 WARNING! WARNING! (Continued) • Check mounting of mats on a regular basis. Always Pedals that cannot move freely can cause loss of properly reinstall and secure floor mats that have vehicle control and increase the risk of serious per- been removed for cleaning.
Page 106: Periodic Safety Checks You Should Make Outside The Vehicle
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Door Latches Periodic Safety Checks You Should Make Outside The Vehicle Check for proper closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 107: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS MIRRORS ......109 ▫ Sun Visor “Slide-On-Rod” Feature — If Equipped .
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE VOICE COMMAND — IF EQUIPPED ..145 ▫ Folding Rear Seat .....162 ▫...
Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 ▫ Map/Reading Lights ....171 ▫ To Vary The Speed Setting ....180 WINDSHIELD WIPERS AND WASHERS .
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Opening Sunroof — Manual Mode ..192 ▫ Glove Compartment And Storage Bin ..200 ▫ Closing Sunroof — Express....192 ▫...
Page 111: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle).
Page 112: Automatic Dimming Mirror - If Equipped
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pushing the button at the base of the mirror. A light to the left of the button will illuminate to indicate when the dimming feature is activated.
Page 113: Outside Mirror - Driver Side
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Outside Mirror — Driver Side WARNING! Adjust the flat outside mirror so you can just see the side Vehicles and other objects seen in the passenger side of your vehicle in the part of the mirror closest to the convex mirror will look smaller and farther away vehicle with your head close to the door glass.
Page 114: Power Mirrors
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To adjust a mirror, turn the control wand toward the left Power Mirrors or right mirror positions indicated. Tilt the control wand The power mirror control is located on the driver’s door in the direction you want the mirror to move. trim panel.
Page 115: Vanity Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Vanity Mirrors — If Equipped Sun Visor “Slide-On-Rod” Feature — If Equipped To use the vanity mirror, rotate the sun visor down and The sun visors may be extended out to provide more swing the mirror cover upward.
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For Uconnect® customer support: paired to the vehicle’s Uconnect® Phone. The Uconnect® Phone allows up to seven mobile phones to be linked to • U.S. residents - visit UconnectPhone.com or call 1-877- the system. Only one linked (or paired) mobile phone can 855-8400.
Page 117: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Uconnect® Phone Button The Uconnect® Phone is fully integrated with the vehi- cle’s audio system. The volume of the Uconnect® Phone The radio or steering wheel controls (if can be adjusted either from the radio volume control equipped) will contain the two control buttons knob or from the steering wheel radio control (right (Uconnect®...
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Prior to giving a voice command, one must wait for the Voice Command Tree beep, which follows the “Ready” prompt or another Refer to “Voice Tree” in this section. prompt. Help Command •...
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Pair (Link) Uconnect® Phone To A Mobile Phone You will be asked to say a four-digit Personal Identifica- tion Number (PIN), which you will later need to enter To begin using your Uconnect® Phone, you must pair into your mobile phone.
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE present in the vehicle, the Uconnect® Phone will use the Call By Saying A Name priority three mobile phone when you make a call. You • Push the Phone button to begin. can select to use a lower priority mobile phone at any time (refer to “Advanced Phone Connectivity”...
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Add Names To Your Uconnect® Phonebook 5. When prompted, recite the phone number for the phonebook entry that you are adding. NOTE: Adding names to the Uconnect® Phonebook is recommended when the vehicle is not in motion. After you are finished adding an entry into the phone- book, you will be given the opportunity to add more To add names to the Uconnect®...
Page 122 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook Download — Automatic Phonebook • A maximum of 1000 entries per phone will be down- Transfer From Mobile Phone loaded and updated every time a phone is connected to the Uconnect® Phone. If equipped and specifically supported by your phone, Uconnect®...
Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Edit Uconnect® Phonebook Entries After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in NOTE: Editing phonebook entries is recommended the phonebook, call the number you just edited, or return when the vehicle is not in motion.
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete Uconnect® Phonebook Entry 4. After you enter the name, the Uconnect® Phone will ask you which designation you wish to delete: home, NOTE: Editing phonebook entries is recommended work, mobile, other, or all. Say the designation you when the vehicle is not in motion.
Page 125: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 3. After confirmation, the phonebook entries will be 3. To call one of the names in the list, push the Voice deleted. Command button during the playing of the desired name, and say “Call.” NOTE: NOTE: The user can also exercise “Edit”...
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer Or Reject An Incoming Call — No Call • Push the Phone button to place the current call on Currently In Progress hold and answer the incoming call. When you receive a call on your mobile phone, the NOTE: The Uconnect®...
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Place/Retrieve A Call From Hold Conference Call To put a call on hold: When two calls are in progress (one active and one on hold): 1. Push the Phone button until you hear a single beep.
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Termination 2. After the “Ready” prompt and the following beep, say “Redial.” To end a call in progress: • The Uconnect® Phone will call the last number that 1. Momentarily push the Phone button.
Page 129: Uconnect® Phone Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 2. After the ignition is cycled to OFF, a call can continue 3. Continue to follow the system prompts to complete on the Uconnect® Phone for a certain duration, after the language selection. which the call is automatically transferred from the After selecting one of the languages, all prompts and Uconnect®...
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the phone is not reachable and the Uconnect® Phone is • If supported, this number may be programmable on operational, you may reach the emergency number as some systems. To do this, push the Phone button follows: and say “Setup,”...
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Roadside Assistance/Towing Assistance Voice Mail Calling If you need roadside assistance: To learn how to access your voice mail, refer to “Working with Automated Systems.” • Push the Phone button to begin. Working With Automated Systems •...
Page 132 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE required to enter your PIN followed with a pound, (3 NOTE: 7 4 6 #), you can push the Voice Command button • You may not hear all of the tones due to mobile phone and say, “3 7 4 6 # Send.”...
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Turning Confirmation Prompts ON/OFF using Uconnect® Phone. The status is given for network signal strength, phone battery strength, etc. Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect® Phone Dialing Using The Mobile Phone Keypad will not repeat a phone number before you dial it).
Page 134: Advanced Phone Connectivity
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mute/Un-Mute (Mute ON/OFF) To transfer an ongoing call from your Uconnect® Phone paired mobile phone to the Uconnect® Phone or vice When you mute the Uconnect® Phone, you will still be versa using Voice Command: able to hear the conversation coming from the other party, but the other party will not be able to hear you.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 List Paired Mobile Phone Names Select Another Mobile Phone This feature allows you to select and start using another • Push the Phone button to begin. phone paired with the Uconnect® Phone. • After the “Ready” prompt and the following beep, say •...
Page 136: Things You Should Know About Your Uconnect® Phone
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete Uconnect® Phone Paired Mobile Phones Voice Training To delete mobile phones paired with the Uconnect® For users experiencing difficulty with the system recog- phone using Voice Commands: nizing their voice commands or numbers, the Uconnect® Phone Voice Training feature may be used.
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 best results, the Voice Training session should be com- Voice Command pleted when the vehicle is parked with the engine For best performance: running, all windows closed, and the blower fan • Adjust the rearview mirror to provide at least ½ inch switched off.
Page 138 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Smooth road surface • Phonebook (Downloaded and Uconnect® Phone Lo- cal) name recognition rate is optimized when the • Fully closed windows entries are not similar. • Dry weather condition • Numbers must be spoken in single digits. “800” must NOTE: be spoken “eight-zero-zero”...
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 • Fully Closed Windows Read Messages: • Dry Weather Conditions If you receive a new text message while your phone is connected to Uconnect® Phone, an announcement will • Operation From The Driver’s Seat be made to notify you that you have a new text message.
Page 140 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Send Messages: List of Preset Messages: You can send messages using Uconnect® Phone. To send 1. Yes. a new message: 2. No. 1. Push the Phone button. 3. Where are you? 2. After the “Ready” prompt and the following beep, say 4.
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 12. I am on my way. To turn Voice Text Reply incoming announcement on or off using Voice Command: 13. I’ll be late. 1. Push the Phone button. 14. Are you there yet? 2.
Page 142 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE I n f o r ma t i o n P r o v i d e d b y :...
Page 143 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 I n f o r ma t i o n P r o v i d e d b y :...
Page 144 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE I n f o r ma t i o n P r o v i d e d b y :...
Page 145 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Voice Commands Primary Alternate (s) Primary Alternate (s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 146 144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Primary Alternate (s) Primary Alternate (s) home redial language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 147: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 General Information VOICE COMMAND — IF EQUIPPED This device complies with Part 15 of the FCC rules and Voice Command System Operation RSS 210 of Industry Canada. Operation is subject to the following conditions: The Uconnect®...
Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pushing the Voice Command button while the WARNING! system is speaking is known as “barging in.” The system will be interrupted, and after the beep, you can Any voice commanded system should be used only add or change commands.
Page 149: Commands
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 To hear the first available Menu, push the Voice Com- Main Menu mand button and say “Help” or “Main Menu.” Start a dialogue by pushing the Voice Command button. You may say “Main Menu” to switch to Commands the main menu.
Page 150 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Radio AM • “Menu Radio” (to switch to the radio menu) To switch to the AM band, say “AM” or “Radio AM.” In • “Main Menu” (to switch to the main menu) this mode, you may say the following commands: Satellite Radio •...
Page 151 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Disc Mode Bluetooth® Streaming (BT) Mode To switch to the disc mode, say “Disc.” In this mode, you To switch to Bluetooth® Streaming (BT) mode, say may say the following commands: “Bluetooth Streaming.” In this mode, you may say the following commands: •...
Page 152 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE – “Save” (to save the memo) Setup – “Continue” (to continue recording) To switch to system setup, you may say one of the following: – “Delete” (to delete the recording) • “Change to setup” •...
Page 153: Voice Training
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 NOTE: Keep in mind that you have to push the Voice blower fan switched off. This procedure may be re- Command button first and wait for the beep peated with a new user. The system will adapt to the before speaking the “Barge In”...
Page 154: Power Seats - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Be sure everyone in your vehicle is in a seat and using a seat belt properly. Power Seats — If Equipped Some models may be equipped with a power driver’s seat.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Adjusting The Seat Forward Or Rearward WARNING! The seat can be adjusted both forward and rearward. • Adjusting a seat while driving may be dangerous. Push the seat switch forward or rearward, the seat will Moving a seat while driving could result in loss of move in the direction of the switch.
Page 156: Heated Seats - If Equipped
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE minutes of continuous operation. At that time, the dis- Heated Seats — If Equipped play will change from HI to LO, indicating the change. On some models, the front driver and passenger seats When the LO-level heating is selected, the system auto- may be equipped with heaters in both the seat cushions matically turns the heater and the indicator light OFF...
Page 157: Manual Front Seat Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! (Continued) • Do not place anything on the seat or seatback that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface tempera- ture of the seat.
Page 158: Manual Seat Height Adjustment - If Equipped
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Height Adjustment — If Equipped WARNING! The driver’s seat height can be raised or lowered by using • Adjusting a seat while driving may be dangerous. a lever, located on the outboard side of the seat. Pull Moving a seat while driving could result in loss of upward on the lever to raise the seat height or push control which could cause a collision and serious...
Page 159: Manual Lumbar - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Manual Lumbar — If Equipped Driver’s Seatback Recline The lumbar adjustment handle is located on the inboard To adjust the seatback, lift the lever located on the or outboard side of the seatback. Rotate the lever down- outboard side of the seat, lean back to the desired angle ward to increase the lumbar support or rotate the lever and release the lever.
Page 160: Head Restraints
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! The head restraints for all occupants must be prop- Do not ride with the seatback reclined so that the erly installed and adjusted prior to operating the shoulder belt is no longer resting against your chest. vehicle or occupying a seat.
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts.
Page 162 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Active Head Restraint (Normal Position) Active Head Restraint (Tilted Position) I n f o r ma t i o n P r o v i d e d b y :...
Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 NOTE: WARNING! • The head restraints should only be removed by quali- • Do not place items over the top of the Active Head fied technicians, for service purposes only. If either of Restraint, such as coats, seat covers or portable the head restraints require removal, see your autho- DVD players.
Page 164: Folding Rear Seat
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Head Restraints The head restraints in the rear are non adjustable. Refer to “Occupant Restraints” in “Things To Know Before Start- ing Your Vehicle” for information on Tether routing. Folding Rear Seat To provide additional storage area, each rear seatback can be folded forward.
Page 165 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 To raise the seatback, pull the strap forward and lift the seatback into its upright position. WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers.
Page 166: Reclining Rear Seat - If Equipped
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Rear Seat — If Equipped TO OPEN AND CLOSE THE HOOD For additional comfort, pull the strap forward just To open the hood, two latches must be released. enough to release the seatback latch. Then push the 1.
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 2. Move the safety catch located under the front edge of Lift the hood prop rod, clipped to the right side (left side the hood, near the center and raise the hood. facing hood) of the engine compartment, to secure the hood in the open position.
Page 168 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To prevent possible damage: Be sure the hood is fully latched before driving your • Before closing hood, make sure the hood prop rod vehicle. If the hood is not fully latched, it could open is fully seated into its storage retaining clips.
Page 169: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 LIGHTS Multifunction Lever The multifunction lever controls the operation of the headlights, parking lights, turn signals, headlight beam selection, instrument panel light dimming, interior lights, the passing lights, and the fog lights. The multifunction lever is located on the left side of the steering column.
Page 170: Headlights And Parking Lights
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights And Parking Lights Daytime Running Lights — If Equipped Turn the end of the multifunction lever to the first detent The high beam lights will come on as Daytime Running to turn on the parking lights. Turn the end of the lever to Lights (lower intensity), whenever the ignition is ON, the the second detent to turn on the headlights.
Page 171: Turn Signals
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Front Fog Light Operation NOTE: The fog lights will only operate with the head- lights on low beam.
Page 172: High/Low Beam Switch
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If either light remains on and does not flash, or Flash-To-Pass there is a very fast flash rate, check for a defective outside You can signal another vehicle with your headlights by light bulb.
Page 173: Map/Reading Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on. Rotate the center portion of the lever upward to the next detent position to brighten the odometer and radio when the parking lights or headlights are on.
Page 174: Windshield Wipers And Washers
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE light off. The lights also come on when a door is opened NOTE: The lights will remain on until the switch is or the dimmer control is turned fully upward, past the pushed a second time, so be sure they have been turned second detent.
Page 175 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 CAUTION! • Turn the windshield wipers off when driving through an automatic car wash. Damage to the windshield wipers may result if the wiper control is left in any position other than off. •...
Page 176: Windshield Wiper Operation
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Intermittent Wiper System Rotate the end of the lever upward to the second detent Use the intermittent wiper when weather conditions past the intermittent settings for low-speed wiper opera- make a single wiping cycle, with a variable pause be- tion.
Page 177: Windshield Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Windshield Washers WARNING! To use the washer, pull the control lever toward you and Sudden loss of visibility through the windshield hold while spray is desired. If the lever is pulled while in could lead to a collision.
Page 178: Tilt Steering Column
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The mist feature does not activate the washer TILT STEERING COLUMN pump; therefore, no washer fluid will be sprayed on the This feature allows you to tilt the steering column windshield. The wash function must be used in order to upward or downward.
Page 179: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 180: To Activate
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Elec- tronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed.
Page 181: To Set A Desired Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 To Deactivate WARNING! A soft tap on the brake pedal, pushing the CANCEL Leaving the Electronic Speed Control system on button, or normal brake pressure while slowing the when not in use is dangerous. You could accidentally vehicle will deactivate the Electronic Speed Control with- set the system or cause it to go faster than you want.
Page 182: To Vary The Speed Setting
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If the button is continually pushed, the set speed will To Vary The Speed Setting continue to increase until the button is released, then To Increase Speed the new set speed will be established. When the Electronic Speed Control is set, you can in- Metric Speed (km/h) crease speed by pushing the RES (+) button.
Page 183: To Accelerate For Passing
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 The drivers preferred units can be selected through the • If the button is continually pushed, the set speed will instrument panel settings if equipped. Refer to “Under- continue to decrease until the button is released, then standing Your Instrument Panel”...
Page 184: Garage Door Opener - If Equipped
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink® buttons, located on either the overhead WARNING! console, headliner or sunvisor, designate the three differ- ent HomeLink® channels. The HomeLink® indicator is Electronic Speed Control can be dangerous where the located above the center button. system cannot maintain a constant speed.
Page 185: Before You Begin Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system.
Page 186: Programming A Rolling Code
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming A Rolling Code For programming garage door openers that were manu- factured after 1995. These garage door openers can be identified by the “LEARN” or “TRAIN” button located where the hanging antenna is attached to the garage door opener.
Page 187 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 Firmly push and release the “LEARN” or “TRAIN- cm) away from the HomeLink® button you wish to ING” button. On some garage door openers/devices program while keeping the HomeLink®...
Page 188: Programming A Non-Rolling Code
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink® Button 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 (Rolling Code) cm) away from the HomeLink® button you wish to program while keeping the HomeLink® indicator To reprogram a channel that has been previously trained, light in view.
Page 189: Canadian/Gate Operator Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 • To program the two remaining HomeLink® buttons, Canadian/Gate Operator Programming repeat each step for each remaining button. DO NOT For programming transmitters in Canada/United States erase the channels. that require the transmitter signals to “time-out” after several seconds of transmission.
Page 190 188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 • If the indicator light stays on constantly, program- cm) away from the HomeLink® button you wish to ming is complete and the garage door/device should program while keeping the HomeLink®...
Page 191: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 3. Without releasing button proceed with The HomeLink® Universal Transceiver is disabled when “Canadian/Gate Operator Programming” step 2 and the Vehicle Security Alarm is active. follow all remaining steps. Troubleshooting Tips Using HomeLink® If you are having trouble programming HomeLink®, To operate, push and release the programmed here are some of the most common solutions:...
Page 192: General Information
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information WARNING! This device complies with FCC rules Part 15 and Industry • Vehicle exhaust contains carbon monoxide, a dan- Canada RSS-210. Operation is subject to the following gerous gas. Do not run your vehicle in the garage two conditions: while programming the transceiver.
Page 193: Power Sunroof - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not ex- pressly approved by the party responsible for compli- ance could void the user’s authority to operate the device.
Page 194: Opening Sunroof - Express
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof — Express WARNING! Push the switch rearward and release it within one-half • Never leave children alone in a vehicle, or with second. The sunroof and sunshade will open automati- access to an unlocked vehicle. Never leave the Key cally from any position.
Page 195: Closing Sunroof - Manual Mode
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 position. The sunroof will close fully and stop automati- Venting Sunroof — Express cally. This is called “Express Close”. During Express Push and release the Vent button within one half second Close operation, any movement of the switch will stop and the sunroof will open to the vent position.
Page 196: Sunroof Maintenance
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE open or partially open positions. This is a normal occur- For Vehicles Equipped With The EVIC rence and can be minimized. If the buffeting occurs with The power sunroof switch will remain active for up to the rear windows open, open the front and rear windows approximately ten minutes after the ignition switch is together to minimize the buffeting.
Page 197 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 NOTE: To ensure proper operation a MOPAR® knob and element must be used. CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.
Page 198 196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
Page 199: Power Inverter - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 Certain high-end video games, such as Playstation®3 CAUTION! (Continued) and XBox360 will exceed this power limit, as will most • Accessories that draw higher power (i.e., coolers, power tools. vacuum cleaners, lights, etc.) will degrade the bat- The power inverter is designed with built-in overload tery even more quickly.
Page 200 198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! To avoid serious injury or death: • Do not use a three-prong adaptor. • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. •...
Page 201: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 CUPHOLDERS CAUTION! (Continued) Your vehicle is equipped with four cupholders. There are • Accessories that draw higher power (i.e., coolers, two illuminated cupholders located in the front. vacuum cleaners, lights, etc.) will degrade the bat- tery even more quickly.
Page 202: Storage
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are two cupholders located in the back for the rear STORAGE passengers. Glove Compartment And Storage Bin Located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. Rear Cupholders Storage Bins 1 —...
Page 203: Door Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 To open the lower glove compartment, pull outward on Door Storage the release handle. The interior door panels are equipped with lower storage areas. Glove Compartment Front Door Storage I n f o r ma t i o n P r o v i d e d b y :...
Page 204: Console Features
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open. Rear Door Storage CONSOLE FEATURES The floor console contains both an upper and lower Upper Storage Compartment storage compartment.
Page 205: Cargo Area Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 CARGO AREA FEATURES Cargo Light The light is mounted in the headliner above the cargo area to illuminate the cargo area. Cargo Cover The cargo area trim panels include two notches for mounting the available tonneau cover that accommo- dates the reclining rear seat.
Page 206 204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Trim Notches Cargo Cover Guides Using the handle, pull the cover toward you and guide the rear cover posts into the guides located on both sides of the rear trim panel. I n f o r ma t i o n P r o v i d e d b y :...
Page 207: Removable Load Floor
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 WARNING! In a collision a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment.
Page 208: Cargo Tie-Down Loops
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Loops WARNING! There are four tie-downs (D-rings) installed in the cargo • Cargo tie-down loops are not safe anchors for a area for securing cargo. child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose.
Page 209: Fold Down Speakers - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 Fold Down Speakers — If Equipped WARNING! (Continued) When the liftgate is open, the speakers can swing down • Place as much cargo as possible in front of the rear off the trim panel to face rearward, for tailgating and axle.
Page 210: Rear Window Features
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Wiper/Washer The rear wiper/washer is controlled by a rotary switch located on the center portion of the control lever. The control lever is located on the right side of the steering column.
Page 211: Rear Window Defroster
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 NOTE: The rear wiper operates in an intermittent mode Rear Window Defroster only. The rear window defroster button is located on Rotate the center portion of the lever past the the climate controls mode control knob. Push the first detent to activate the rear washer.
Page 212: Roof Luggage Rack - If Equipped
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ROOF LUGGAGE RACK — IF EQUIPPED CAUTION! The crossbars and siderails are designed to carry the Failure to follow these cautions can cause damage to cargo on vehicles equipped with a luggage rack. The load the heating elements: must not exceed 150 lbs (68 kg), and should be uniformly •...
Page 213 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 The crossbars must also be secured in one of the seven improved satellite radio reception, place the rear cross- detent positions marked with an arrow on the siderails to bar in the second detent from the rear of the vehicle prevent movement.
Page 214 212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! • Long loads which extend over the windshield, such Cargo must be securely tied before driving your as wood panels or surfboards, or loads with large vehicle. Improperly secured loads can fly off the frontal area should be secured to both the front and vehicle, particularly at high speeds, resulting in per- rear of the vehicle.
Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT PANEL FEATURES ..216 ▫ Compass/Temperature/Audio ... .239 INSTRUMENT CLUSTER ....217 ▫...
Page 216 214 UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions — Radio Mode..246 Uconnect® 130 ......267 ▫...
Page 217 UNDERSTANDING YOUR INSTRUMENT PANEL 215 iPod®/USB/MP3 CONTROL — IF EQUIPPED . .293 ▫ Radio Operation ..... .300 ▫ Connecting The iPod® Or External USB ▫...
Page 218: Instrument Panel Features
216 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Outlet 5 — Storage Bin 9 — Heated Seat Switch – If Equipped 2 — Demisters 6 — Glove Compartment 10 — Hazard Warning Flasher 3 — Instrument Cluster 7 —...
Page 219: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 217 INSTRUMENT CLUSTER I n f o r ma t i o n P r o v i d e d b y :...
Page 220: Instrument Cluster Descriptions
218 UNDERSTANDING YOUR INSTRUMENT PANEL If jump starting is required, refer to “Jump Starting INSTRUMENT CLUSTER DESCRIPTIONS Procedures” in “What To Do In Emergencies.” 1. Fuel Gauge/Fuel Door Reminder 3. Electronic Throttle Control (ETC) Light When the ignition switch is in the ON/RUN position, the pointer will show the level of fuel This light informs you of a problem with the remaining in the fuel tank.
Page 221 UNDERSTANDING YOUR INSTRUMENT PANEL 219 on briefly as a bulb check. If the light does not come on 6. Speedometer during starting, have the system checked by an autho- The Speedometer shows the vehicle speed in miles per rized dealer. hour (MPH) and kilometers per hour (km/h).
Page 222 220 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If either indicator flashes at a rapid rate, check If the ABS light is on, the brake system should be serviced for a defective outside light bulb. as soon as possible to restore the benefits of Anti-Lock brakes.
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 221 12. Tachometer normal, turn the engine off immediately and call for service. Refer to “If Your Engine Overheats” in “What To The white area of the scale shows the permissible engine Do In Emergencies” for further information. revolutions-per-minute (RPM x 1000) for each gear range.
Page 224 222 UNDERSTANDING YOUR INSTRUMENT PANEL booster, the ABS pump will run when applying the brake, WARNING! and a brake pedal pulsation may be felt during each stop. Driving a vehicle with the red brake light on is The dual brake system provides a reserve braking capac- dangerous.
Page 225 UNDERSTANDING YOUR INSTRUMENT PANEL 223 The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON/RUN posi- tion. If you continue operating the vehicle when the Transmission Temperature Warning Light is illumi- NOTE: This light shows only that the parking brake is nated you could cause the fluid to boil over, come in applied.
Page 226 224 UNDERSTANDING YOUR INSTRUMENT PANEL 17. Temperature Gauge CAUTION! (Continued) The temperature gauge shows engine coolant tempera- turn the engine off immediately and call an autho- ture. Any reading within the normal range indicates that rized dealer for service. the engine cooling system is operating satisfactorily. The gauge pointer will likely indicate a higher tempera- WARNING! ture when driving in hot weather, up mountain grades,...
Page 227 UNDERSTANDING YOUR INSTRUMENT PANEL 225 19. 4WD Indicator Light If the vehicle is equipped with the optional Electronic Vehicle Information Center (EVIC) in the instrument This light indicates the vehicle is in 4WD Locked mode. cluster, refer to “Electronic Vehicle Information Center — 20.
Page 228 226 UNDERSTANDING YOUR INSTRUMENT PANEL Accordingly, when the low tire pressure telltale illumi- illuminated. This sequence will continue upon subse- nates, you should stop and check your tires as soon as quent vehicle start-ups as long as the malfunction exists. possible, and inflate them to the proper pressure.
Page 229 UNDERSTANDING YOUR INSTRUMENT PANEL 227 NOTE: U.S. Federal regulations require that upon trans- CAUTION! (Continued) fer of vehicle ownership, the seller certify to the pur- equipped on your vehicle. Undesirable system opera- chaser the correct mileage that the vehicle has been tion or sensor damage may result when using re- driven.
Page 230 228 UNDERSTANDING YOUR INSTRUMENT PANEL area. Tighten the fuel filler cap properly and push the gATE ......Gate Ajar TRIP ODOMETER button to turn off the message.
Page 231 UNDERSTANDING YOUR INSTRUMENT PANEL 229 position. To turn off the message temporarily, push and 24. OFF ROAD Indicator — If Equipped release the Trip Odometer button on the instrument The symbol illuminates (is armed) when the 4WD lock cluster. To reset the oil change indicator system (after switch is activated and the shift lever is in LOW or performing the scheduled maintenance), refer to the REVERSE position.
Page 232 230 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Hill Descent Indicator — If Equipped CAUTION! The symbol illuminates (is armed) when the Prolonged driving with the Malfunction Indicator 4WD Lock switch is activated and the trans- Light (MIL) on could cause damage to the engine mission range indicator is in LOW or REVERSE control system.
Page 233 UNDERSTANDING YOUR INSTRUMENT PANEL 231 29. Electronic Stability Control (ESC) Activation/ NOTE: Malfunction Indicator Light — If Equipped • The “ESC Off Indicator Light” and the “ESC Activation/Malfunction Indicator Light” come on The “ESC Activation/Malfunction Indicator momentarily each time the ignition switch is turned Light”...
Page 234: Mini-Trip Computer - If Equipped
232 UNDERSTANDING YOUR INSTRUMENT PANEL check, when the ignition key is turned to the ON/RUN MINI-TRIP COMPUTER — IF EQUIPPED position and may stay on for as long as three seconds. The Mini-Trip Computer is located in the instrument When lit solid: There is a 4WD system fault. 4WD cluster and features a driver-interactive trip information performance will be at a reduced level.
Page 235: Control Buttons
UNDERSTANDING YOUR INSTRUMENT PANEL 233 RESET Button Control Buttons To reset the display shown, turn the ignition switch to the ON position, then push and hold the RESET button located on the steering wheel. The following displays can be reset or changed: •...
Page 236: Electronic Vehicle Information Center (Evic) - If Equipped
234 UNDERSTANDING YOUR INSTRUMENT PANEL Trip B Shows the total distance traveled for Trip B since the last reset. ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) — IF EQUIPPED The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the instrument cluster.
Page 237 UNDERSTANDING YOUR INSTRUMENT PANEL 235 • Personal Settings (Customer-Programmable Features) The system allows the driver to select information by pushing the following buttons mounted on the steering • Compass Heading wheel: • Outside Temperature Display • Trip Computer Functions • Uconnect® Phone Displays (if equipped) •...
Page 238 236 UNDERSTANDING YOUR INSTRUMENT PANEL MENU Button DOWN Button Push and release the MENU button to scroll Push and release the DOWN button to scroll through the main menus (Fuel Economy, Warn- downward through the submenus. ings, Timer, Units, System, Personal Settings) or to exit submenus.
Page 239: Engine Oil Change Indicator System - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 237 • Personal Settings Not Avail. — Vehicle is not in PARK • Remote Start Aborted — Fuel Low (automatic transmission), or vehicle is in motion • Remote Start Aborted — System Fault (manual transmission). • Key In Ignition •...
Page 240: Evic Functions
238 UNDERSTANDING YOUR INSTRUMENT PANEL indicator system is duty-cycle based, which means the NOTE: If the indicator message illuminates when you engine oil change interval may fluctuate dependent upon start the vehicle, the oil change indicator system did not your personal driving style. reset.
Page 241: Compass/Temperature/Audio
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Reset will only occur if a resettable function is currently history information will be erased, and the averaging will being displayed. To reset all resettable functions, push continue from the last fuel reading before the reset. and release the RIGHT/SELECT arrow button a second Distance To Empty (DTE) time within three seconds of resetting the currently...
Page 242: Tire Pressure Monitor (Tpm)
240 UNDERSTANDING YOUR INSTRUMENT PANEL LOW FUEL text and a new DTE value will be dis- Upon reset, all digits will change to zeros, and time will played, based on the current values in the DTE calcula- start incrementing again if the ignition switch is in RUN tion and the current fuel tank level.
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 241 Use the SELECT button to display one of the following and hold the RIGHT arrow button when in this display choices: until “ON” or “OFF” appears to make your selection. Language Auto Unlock On Exit When in this display, you may select different languages When ON is selected, all the vehicle’s doors will unlock for all display nomenclature, including the trip functions.
Page 244 242 UNDERSTANDING YOUR INSTRUMENT PANEL button. Push and hold the RIGHT arrow button when in Headlamp Off Delay this display until “Driver’s Door 1st” or “All Doors” When this feature is selected the driver can choose to appears to make your selection. have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle.
Page 245 UNDERSTANDING YOUR INSTRUMENT PANEL 243 Illuminated Approach Push and hold the RIGHT arrow button when in this display until “U.S” or “METRIC” appears to make your When this feature is selected, the headlights will activate selection. and remain on for up to 90 seconds when the doors are unlocked using the RKE transmitter.
Page 246 244 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Compass Calibration 5. Complete one or more 360–degree turns (in an area free from large metal or metallic objects) until the If the compass appears erratic and the “CAL” indicator “CAL” indicator turns off. The compass will now does not appear in the EVIC display, you must put the function normally.
Page 247 UNDERSTANDING YOUR INSTRUMENT PANEL 245 1. Turn the ignition switch ON. 2. Push and hold the COMPASS button for approxi- mately two seconds. 3. Push and release the DOWN button until “Compass Variance” message and the last variance zone number displays in the EVIC.
Page 248: Uconnect® 230 - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer
246 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect® 230 – AM/FM STEREO RADIO AND Operating Instructions — Radio Mode 6–DISC CD/DVD CHANGER (MP3/WMA AUX NOTE: The ignition switch must be in the ON or ACC JACK) position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio.
Page 249 UNDERSTANDING YOUR INSTRUMENT PANEL 247 SEEK Buttons Voice Command Button Uconnect® Phone — If Equipped Push and release the SEEK buttons to search for the next listenable station in AM/FM mode. Push the right switch Push this button to operate the Uconnect® Phone feature to seek up and the left switch to seek down.
Page 250 248 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button The clock can also be set by pushing the SETUP button and selecting the “SET HOME CLOCK” entry. Once in this Push the TIME button to alternate locations of the time display follow the above procedure, starting at step 2. and frequency display.
Page 251 UNDERSTANDING YOUR INSTRUMENT PANEL 249 Setting The Tone, Balance And Fade Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display.
Page 252 250 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following 16-Digit Character Dis- Program Type format types: play Oldies Oldies 16-Digit Character Dis- Program Type Personality Persnlty play Public Public No program type or un- None defined Rhythm and Blues R &...
Page 253 UNDERSTANDING YOUR INSTRUMENT PANEL 251 By pushing the SEEK button when the Music Type icon is • DVD Enter — When the disc is in DVD Menu mode, displayed, the radio will be tuned to the next frequency selecting DVD Enter will allow you to play the current station with the same selected Music Type name.
Page 254 252 UNDERSTANDING YOUR INSTRUMENT PANEL • Angle — Repeatedly pushing SELECT will change • Set Home Clock — Pushing the SELECT button the viewing angle if supported by the DVD disc (if allows you to set the clock. Turn the TUNE/SCROLL equipped).
Page 255 UNDERSTANDING YOUR INSTRUMENT PANEL 253 Audio Language — If Equipped Audio DRC — If Equipped Selecting this item allows you to choose a default audio Selecting this item allows you to limit maximum audio language (effective only if the language is supported by dynamic range.
Page 256 254 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The user will have to set these defaults before You may add a second station to each pushbutton by loading a disc. If changes are made to these settings after repeating the above procedure with this exception: Push a disc is loaded, changes will not be effective.
Page 257: Operation Instructions - Disc Mode For Cd And Mp3/Wma Audio Play, Dvd - Video
UNDERSTANDING YOUR INSTRUMENT PANEL 255 DISC Button CAUTION! (Continued) Pushing the DISC button will allow you to switch from “Disc Hot” and shut off until a safe temperature is AM/FM modes to Disc modes. reached. This shutdown is necessary to protect the optics of the DVD player and other radio internal Operation Instructions —...
Page 258 256 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD MODE) CAUTION! Push the right SEEK button for the next selection on the This CD player will accept 4–3/4 inch (12 cm) discs CD. Push the left SEEK button to return to the beginning only.
Page 259: Notes On Playing Mp3/Wma Files
UNDERSTANDING YOUR INSTRUMENT PANEL 257 RW/FF (CD MODE) Supported Medium Formats (File Systems) Push and hold FF (Fast Forward) and the CD player will The medium formats supported by the radio are ISO 9660 begin to fast forward until FF is released, or RW or Level 1 and Level 2 and includes the Joliet extension.
Page 260 258 UNDERSTANDING YOUR INSTRUMENT PANEL Multisession disc formats are supported by the radio. When using the MP3/WMA encoder to compress audio Multisession discs may contain combinations of normal data to an MP3/WMA file, the bit rate and sampling CD audio tracks and computer files (including MP3/ frequencies in the following table are supported.
Page 261 UNDERSTANDING YOUR INSTRUMENT PANEL 259 Loading times for playback of MP3/WMA files may be Sampling affected by the following: Frequency Bit Rate (kbps) Specification (kHz) • Media - CD-RW media may take longer to load than 44.1 and 48 48, 64, 96, 128, CD-R media 160, 192 VBR •...
Page 262: List Button - Disc Mode For Mp3/Wma Play
260 UNDERSTANDING YOUR INSTRUMENT PANEL Push and hold the INFO button again for three seconds LIST Button — DISC Mode For MP3/WMA Play to return to elapsed time display. Pushing the LIST button will bring up a list of all folders on the disc.
Page 263: Operating Instructions (Uconnect® Phone) - If
UNDERSTANDING YOUR INSTRUMENT PANEL 261 SCAN Button (Auxiliary Mode) Operating Instructions (Voice Command System) — If Equipped No function. Refer to “Voice Command” for further details. EJECT Button (Auxiliary Mode) Operating Instructions (Uconnect® Phone) — If Equipped No function. Refer to “Uconnect® Phone” for further details. Dolby®...
Page 264: Uconnect® (Satellite Radio) - If Equipped
262 UNDERSTANDING YOUR INSTRUMENT PANEL intended for home and other limited viewing uses only, System Activation unless otherwise authorized by Macrovision. Reverse Sirius Satellite Radio service is pre-activated, and you engineering or disassembly is prohibited. may begin listening immediately to the one year of audio service that is included with the factory-installed satellite DTS™...
Page 265 UNDERSTANDING YOUR INSTRUMENT PANEL 263 To access the ESN/SID, refer to the following steps: decreased performance. Larger luggage items such as bikes should be placed as far rearward as possible, within ESN/SID Access the loading design of the rack. Do not place items directly With the ignition switch in the ON/RUN or ACC posi- on or above the antenna.
Page 266 264 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Uconnect® (Satellite) INFO Button Mode Pushing the INFO button will cycle the display informa- tion between Artist, Song Title, and Composer (if avail- NOTE: The ignition switch must be in the ON/RUN or able).
Page 267 UNDERSTANDING YOUR INSTRUMENT PANEL 265 MUSIC TYPE Button SETUP Button Pushing this button once will turn on the Music Type Pushing the SETUP button allows you to select the mode for five seconds. Pushing the MUSIC TYPE button following items: or turning the TUNE/SCROLL control knob within five •...
Page 268: If Equipped
266 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second channel to each pushbutton by Uconnect® 730N/430/430N CD/DVD/HDD/NAV — repeating the above procedure with this exception: Push IF EQUIPPED the SET button twice and SET 2 will show in the display Refer to your Uconnect®...
Page 269: Uconnect® 130
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Power Switch/Volume Control (Rotary) Uconnect® 130 Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction, without stopping.
Page 270 268 UNDERSTANDING YOUR INSTRUMENT PANEL another selection. Holding either button will bypass 5. To exit, push any button/knob, or wait five seconds. stations without stopping, until you release it. RW/FF TIME Button Pushing the RW (Rewind) or FF (Fast Forward) buttons Push the TIME button to alternate display of the time and causes the tuner to search for the next frequency in the radio frequency.
Page 271 UNDERSTANDING YOUR INSTRUMENT PANEL 269 Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones.
Page 272: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
270 UNDERSTANDING YOUR INSTRUMENT PANEL display window. Each button can be set for SET 1 and Operation Instructions — CD MODE For CD And SET 2 in both AM and FM. This allows a total of 12 AM MP3 Audio Play and 12 FM stations to be stored into pushbutton memory.
Page 273 UNDERSTANDING YOUR INSTRUMENT PANEL 271 If you insert a disc with the ignition ON and the radio CAUTION! (Continued) ON, the unit will switch from radio to CD mode and • Dual-media disc types (one side is a DVD, the begin to play when you insert the disc.
Page 274: Notes On Playing Mp3 Files
272 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button AM/FM Button Push the right SEEK button for the next selection on the Push the button to select either AM or FM mode. CD. Push the left SEEK button to return to the beginning SET/RND Button (Random Play Button) of the current selection, or return to the beginning of the Push this button while the CD is playing to activate...
Page 275 UNDERSTANDING YOUR INSTRUMENT PANEL 273 Supported Media (Disc Types) display the file name and folder name, and will assign a number instead. With a maximum number of files, The MP3 file recording media supported by the radio are exceeding 20 folders will result in this display. With CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
Page 276 274 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats Sampling MPEG Frequency Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- Specification (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is MPEG-1 Audio 48, 44.1, 32 320, 256, 224,...
Page 277: Operation Instructions - Auxiliary Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 275 Playback Of MP3 Files To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a When a medium containing MP3 data is loaded, the single-session disc, enable the “Disc at Once” option radio checks all files on the medium.
Page 278: Uconnect® 130 With Satellite Radio
276 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Operating Instructions — Radio Mode Push this button to change the display to time of day. The NOTE: The ignition switch must be in the ON or ACC time of day will display for five seconds (when ignition is position to operate the radio.
Page 279 UNDERSTANDING YOUR INSTRUMENT PANEL 277 SEEK Buttons If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With Push and release the SEEK buttons to search for the next Uconnect Phone” message will display on the radio listenable station in AM/FM mode.
Page 280 278 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure starting at step 2. For vehicles not equipped with satellite radio, push the SETUP button and then follow the above 1. Push and hold the TIME button until the hours blink. procedure, starting at step 2. 2.
Page 281 UNDERSTANDING YOUR INSTRUMENT PANEL 279 Setting The Tone, Balance And Fade Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control Push the rotary TUNE/SCROLL control knob and BASS knob to the left or right to adjust the sound level between will display.
Page 282 280 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following 16-Digit Character Dis- Program Type format types: play Oldies Oldies 16-Digit Character Dis- Program Type Personality Persnlty play Public Public No program type or un- None defined Rhythm and Blues R &...
Page 283 UNDERSTANDING YOUR INSTRUMENT PANEL 281 By pushing the SEEK button when the Music Type icon is the minutes using the right side TUNE/SCROLL con- displayed, the radio will be tuned to the next frequency trol knob. Push the TUNE/SCROLL control knob to station with the same selected Music Type name.
Page 284: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
282 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by Operation Instructions — CD MODE For CD And repeating the above procedure with this exception: Push MP3 Audio Play the SET/RND button twice and SET 2 will show in the NOTE: display window.
Page 285 UNDERSTANDING YOUR INSTRUMENT PANEL 283 If you insert a disc with the ignition ON and the radio CAUTION! (Continued) ON, the unit will switch from radio to CD mode and • Dual-media disc types (one side is a DVD, the begin to play when you insert the disc.
Page 286: Notes On Playing Mp3 Files
284 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button AM/FM Button Push the right SEEK button for the next selection on the Push the button to select either AM or FM mode. CD. Push the left SEEK button to return to the beginning SET/RND Button (Random Play Button) of the current selection, or return to the beginning of the Push this button while the CD is playing to activate...
Page 287 UNDERSTANDING YOUR INSTRUMENT PANEL 285 Supported Media (Disc Types) display the file name and folder name, and will assign a number instead. With a maximum number of files, The MP3 file recording media supported by the radio are exceeding 20 folders will result in this display. With CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
Page 288 286 UNDERSTANDING YOUR INSTRUMENT PANEL Supported MP3 File Formats Sampling MPEG Frequency Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- Specification (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems. The radio is MPEG-1 Audio 48, 44.1, 32 320, 256, 224,...
Page 289: List Button - Cd Mode For Mp3 Play
UNDERSTANDING YOUR INSTRUMENT PANEL 287 Playback Of MP3 Files To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a When a medium containing MP3 data is loaded, the single-session disc, enable the “Disc at Once” option radio checks all files on the medium.
Page 290: Uconnect® (Satellite Radio) - If Equipped
288 UNDERSTANDING YOUR INSTRUMENT PANEL Push the INFO button once more to return to elapsed NOTE: The AUX device must be turned on and the time priority mode. device’s volume set to the proper level. If the AUX audio is not loud enough, turn the device’s volume up. If the Push and hold the INFO button for three seconds or more AUX audio sounds distorted, turn the device’s volume and the radio will display song titles for each file.
Page 291 UNDERSTANDING YOUR INSTRUMENT PANEL 289 NOTE: Sirius service is not available in Hawaii and has Electronic Serial Number/Sirius Identification limited coverage in Alaska. Number (ESN/SID) Please have the following information available when System Activation calling: Sirius Satellite Radio service is pre-activated, and you may begin listening immediately to the one year of audio 1.
Page 292 290 UNDERSTANDING YOUR INSTRUMENT PANEL Selecting Uconnect® (Satellite) Mode • Dense tree coverage may interrupt reception in the form of short audio mutes. Push the SAT button until SAT appears in the display. A CD may remain in the radio while in the Satellite radio •...
Page 293 UNDERSTANDING YOUR INSTRUMENT PANEL 291 SCAN Button TUNE Control (Rotary) Pushing the SCAN button causes the tuner to search for Turn the rotary TUNE/SCROLL control knob clockwise the next channel, pausing for eight seconds before con- to increase or counterclockwise to decrease the channel. tinuing to the next.
Page 294 292 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button You may add a second channel to each pushbutton by repeating the above procedure with this exception: Push Pushing the SETUP button allows you to select the the SET button twice and SET 2 will show in the display following items: window.
Page 295: Ipod®/Usb/Mp3 Control - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 293 iPod®/USB/MP3 CONTROL — IF EQUIPPED Connecting The iPod® Or External USB Device This feature allows an iPod® or external USB device to be Use the connection cable to connect an iPod® or external plugged into the USB port, located in the center console USB device to the vehicle’s USB/AUX connector port or glove compartment.
Page 296: Using This Feature
294 UNDERSTANDING YOUR INSTRUMENT PANEL Once the audio device is connected and synchronized to • The audio device can be controlled using the radio the vehicle’s iPod®/USB/MP3 control system (iPod® or buttons to Play, Browse, and List the iPod® contents. external USB device may take a few minutes to connect), •...
Page 297 UNDERSTANDING YOUR INSTRUMENT PANEL 295 mode. In Play mode, the following buttons on the radio • A single push backward << RW or forward FF >> will faceplate may be used to control the iPod® or external jump backward or forward respectively, for five sec- USB device and display data: onds.
Page 298: List Or Browse Mode
296 UNDERSTANDING YOUR INSTRUMENT PANEL • Push the SCAN button to use iPod®/USB/MP3 de- List Or Browse Mode vice scan mode, which will play the first ten seconds of During Play mode, pushing any of the buttons described each track in the current list and then forward to the below, will bring up List mode.
Page 299 UNDERSTANDING YOUR INSTRUMENT PANEL 297 During all List modes, the iPod® displays all lists in To exit List mode without selecting a track, push the “wrap-around” mode. So if the track is at the bottom of same PRESET button again to go back to Play mode. the list, just turn the wheel backward (counterclockwise) LIST button: The LIST button will display the top level to get to the track faster.
Page 300: Bluetooth® Streaming Audio (Btsa)
298 UNDERSTANDING YOUR INSTRUMENT PANEL Bluetooth® Streaming Audio (BTSA) CAUTION! Music can be streamed from your cellular phone to the • Leaving the iPod® or external USB device (or any Uconnect® phone system. supported device) anywhere in the vehicle in ex- Refer to the Uconnect®...
Page 301: Steering Wheel Audio Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 299 Selecting A Different Audio Device Browse Browsing is not available on a Bluetooth® Streaming 1. Push the Phone button to begin. Audio (BTSA) device. Only the current song that is 2. After the Ready prompt and following the beep, say playing will display info.
Page 302: Radio Operation
300 UNDERSTANDING YOUR INSTRUMENT PANEL Pushing the center button will make the radio switch between the various modes available (AM/FM/SAT/ CD/HDD/AUX etc.). The left-hand control is a rocker-type switch with a push-button in the center. The function of the left-hand control is different depending on which mode you are in.
Page 303: Cd Player
UNDERSTANDING YOUR INSTRUMENT PANEL 301 CD Player CD/DVD DISC MAINTENANCE Pushing the top of the switch once will go to the next To keep a CD/DVD in good condition, take the following track on the CD. Pushing the bottom of the switch once precautions: will go to the beginning of the current track, or to the 1.
Page 304: Radio Operation And Mobile Phones
302 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Store the disc in its case after playing. RADIO OPERATION AND MOBILE PHONES Under certain conditions, the mobile phone being on in 6. Do not expose the disc to direct sunlight. your vehicle can cause erratic or noisy performance from 7.
Page 305: Manual Heating And Air Conditioning
UNDERSTANDING YOUR INSTRUMENT PANEL 303 Blower Control Manual Heating And Air Conditioning Rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position.
Page 306 304 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If your air conditioning performance seems lower NOTE: The air conditioning compressor will not engage than expected, check the front of the A/C condenser until the engine has been running for about 10 seconds. located in front of the radiator for an accumulation of dirt •...
Page 307 UNDERSTANDING YOUR INSTRUMENT PANEL 305 Mode Control (Air Direction) • Bi-Level Air is directed through the panel and floor outlets. Rotate this control to choose from sev- NOTE: For all settings, except full cold or full hot, eral patterns of air distribution. You there is a difference in temperature between the upper can select either a primary mode as and lower outlets.
Page 308 306 UNDERSTANDING YOUR INSTRUMENT PANEL • Defrost • Recirculation Control Air is directed through the windshield and side Pushing the Recirculation Control button will window demist outlets. Use this mode with maxi- put the system in recirculation mode. This can mum blower and temperature settings for best wind- be used when outside conditions such as shield and side window defrosting.
Page 309: Automatic Temperature Control (Atc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 307 • The A/C will engage automatically to prevent fogging when the recirculation button is pushed and the mode control is set to panel or panel / floor. • The A/C can be deselected manually without disturb- ing the mode control selection.
Page 310 308 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The AUTO position performs best for front seat You will experience the greatest efficiency by simply occupants only. allowing the system to function automatically. Selecting the “O” (OFF) position on the blower control stops the system completely and closes the outside air intake.
Page 311 UNDERSTANDING YOUR INSTRUMENT PANEL 309 insects. Clean with a gentle water spray from behind Manual Operation Override the radiator and through the condenser. Fabric front This system offers a full complement of manual override fascia protectors may reduce airflow to the condenser, features, which consist of Blower Preferred Automatic, reducing air conditioning performance.
Page 312 310 UNDERSTANDING YOUR INSTRUMENT PANEL I n f o r ma t i o n P r o v i d e d b y :...
Page 313 UNDERSTANDING YOUR INSTRUMENT PANEL 311 The operator can override the AUTO mode setting to • Floor change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and •...
Page 314 312 UNDERSTANDING YOUR INSTRUMENT PANEL • Air Conditioner Control NOTE: Push this button to turn on the air • When the ignition switch is turned to the LOCK conditioning during manual operation position, the recirculation feature will be cancelled. only. When the air conditioning is •...
Page 315: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 313 • Most of the time, when in Automatic Operation, you Summer Operation can temporarily put the system into Recirculation The engine cooling system must be protected with a Mode by pushing the Recirculation button. However, high-quality antifreeze coolant to provide proper corro- under certain conditions, while in Automatic Mode, sion protection and to protect against engine overheating.
Page 316 314 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow, and if they windshield and provide sufficient heating.
Page 317 UNDERSTANDING YOUR INSTRUMENT PANEL 315 Control Setting Suggestions For Various Weather Conditions I n f o r ma t i o n P r o v i d e d b y :...
Page 318 I n f o r ma t i o n P r o v i d e d b y :...
Page 319 STARTING AND OPERATING CONTENTS STARTING PROCEDURES ....321 ▫ Five-Speed Manual Transmission...324 ▫ Manual Transmission — If Equipped ..321 ▫...
Page 320 318 STARTING AND OPERATING AUTOSTICK ......342 ▫ Power Steering Fluid Check ....356 ▫...
Page 321 STARTING AND OPERATING 319 TIRE SAFETY INFORMATION ... . .374 ▫ Tire Spinning ......395 ▫...
Page 322 320 STARTING AND OPERATING ▫ Reformulated Gasoline ....410 TRAILER TOWING .....418 ▫...
Page 323: Starting Procedures
STARTING AND OPERATING 321 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both • Do not leave the Key Fob in or near the vehicle, or inside and outside mirrors, and fasten your seat belts. in a location accessible to children. A child could operate power windows, other controls, or move WARNING! the vehicle.
Page 324: Automatic Transmission - If Equipped
322 STARTING AND OPERATING Automatic Transmission — If Equipped Normal Starting The shift lever must be in the PARK or NEUTRAL Normal starting of either a cold or a warm engine does position before you can start the engine. Depress the not require pumping or pressing the accelerator pedal.
Page 325: Extreme Cold Weather
STARTING AND OPERATING 323 in the ON position, release the accelerator pedal and WARNING! (Continued) repeat the “Normal Starting” procedure. another vehicle. This type of start can be dangerous if done improperly, so follow the procedure carefully. WARNING! Refer to “Jump Starting” in “What To Do In Emer- Never pour fuel or other flammable liquid into the gencies”...
Page 326: Engine Block Heater - If Equipped
324 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED MANUAL TRANSMISSION — IF EQUIPPED The engine block heater warms the engine, and permits Five-Speed Manual Transmission quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a WARNING! grounded, three-wire extension cord.
Page 327 STARTING AND OPERATING 325 CAUTION! • Launching in any gear except 1st gear will result in excessive slipping of the clutch and potentially lugging or stalling the engine. • Use each gear in numerical order, do not skip a gear. Be sure the transmission is in first gear, (not third), when starting from a standing position.
Page 328: Recommended Shift Speeds
326 STARTING AND OPERATING Never shift into REVERSE until the vehicle has come to a Recommended Shift Speeds complete stop. To use your manual transmission for optimal fuel economy, it should be upshifted as listed in the following NOTE: During cold weather, until the transmission lu- table.
Page 329: Downshifting
STARTING AND OPERATING 327 When turning a corner or driving up a steep grade, Downshifting downshift early so that the engine will not be overbur- Proper downshifting will improve fuel economy and dened. prolong engine life. AUTOMATIC TRANSMISSION — IF EQUIPPED CAUTION! CAUTION! If you skip a gear while downshifting or downshift...
Page 330 328 STARTING AND OPERATING NOTE: You must press and hold the brake pedal while WARNING! (Continued) shifting out of PARK. • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, WARNING! you should never exit a vehicle while the engine is •...
Page 331: Key Ignition Park Interlock
STARTING AND OPERATING 329 OFF (key removal) position. The key can only be re- WARNING! (Continued) moved from the ignition when the ignition is in the • Never leave children alone in a vehicle, or with LOCK/OFF position, and once removed the transmission access to an unlocked vehicle.
Page 332: Six-Speed Automatic Transmission - If Equipped
330 STARTING AND OPERATING The transmission shift lever has only PARK, REVERSE, Six-Speed Automatic Transmission — If Equipped NEUTRAL, and DRIVE shift positions. Manual shifts can The transmission gear position display (located in the be made using the AutoStick shift control (refer to instrument cluster) indicates the transmission gear range.
Page 333 STARTING AND OPERATING 331 Never attempt to use PARK while the vehicle is in WARNING! motion. Apply the parking brake when leaving the vehicle in this range. • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake When parking on a level surface, you may shift the fully when parked to guard against vehicle move- transmission into PARK first, and then apply the parking...
Page 334 332 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Never leave children alone in a vehicle, or with those in or near the vehicle. As with all vehicles, access to an unlocked vehicle. Allowing children to you should never exit a vehicle while the engine is be in a vehicle unattended is dangerous for a running.
Page 335 STARTING AND OPERATING 333 • Look at the transmission gear position display and CAUTION! verify that it indicates the PARK position (P). • Before moving the shift lever out of PARK, you • With brake pedal released, verify that the shift lever must turn the ignition switch from the LOCK/OFF will not move out of PARK.
Page 336 334 STARTING AND OPERATING DRIVE (D) WARNING! This range should be used for most city and highway Do not coast in NEUTRAL and never turn off the driving. It provides the smoothest upshifts and down- ignition to coast down a hill. These are unsafe shifts, and the best fuel economy.
Page 337 STARTING AND OPERATING 335 If the transmission temperature exceeds normal operat- Mode is activated. In this mode, the transmission remains ing limits, the transmission controller will modify the in fourth gear regardless of which forward gear is transmission shift schedule and expand the range of selected.
Page 338 336 STARTING AND OPERATING 6. Shift into the desired gear range. If the problem is no • The transmission fluid has reached an adequate tem- longer detected, the transmission will return to normal perature. operation. • The engine coolant has reached an adequate tempera- NOTE: Even if the transmission can be reset, we recom- ture.
Page 339: Continuously Variable Automatic Transmission (Cvt) - If Equipped
STARTING AND OPERATING 337 NOTE: Engagement of the torque converter clutch is NOTE: The Continuously Variable Automatic Transmis- inhibited at very cold temperatures. Because the engine sion (CVT) changes ratios in a continuous manner. This speed is higher when the torque converter clutch is not may sometimes feel as if it is slipping, but this is normal engaged, it may seem as if the transmission is not shifting and does not harm anything.
Page 340 338 STARTING AND OPERATING Gear Ranges the transmission locking mechanism may make it diffi- cult to move the shift lever out of PARK. As an added DO NOT race the engine when shifting from PARK or precaution, turn the front wheels toward the curb on a NEUTRAL into another gear range.
Page 341 STARTING AND OPERATING 339 WARNING! (Continued) WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL locked in PARK, securing the vehicle against un- if the engine speed is higher than idle speed. If wanted movement. your foot is not firmly pressing the brake pedal, the •...
Page 342 340 STARTING AND OPERATING • Look at the transmission gear position display and CAUTION! verify that it indicates the PARK position (P). • Before moving the shift lever out of PARK, you • With brake pedal released, verify that the shift lever must turn the ignition switch from the LOCK/OFF will not move out of PARK.
Page 343 STARTING AND OPERATING 341 DRIVE (D) WARNING! This range should be used for most city and highway Do not coast in NEUTRAL and never turn off the driving. It provides the best fuel economy. The DRIVE ignition to coast down a hill. These are unsafe position provides optimum driving characteristics under practices that limit your response to changing traffic all normal operating conditions.
Page 344: Autostick
342 STARTING AND OPERATING this happens, the transmission overheat indicator light braking, eliminate undesirable upshifts and downshifts, will come on, and the vehicle will slow slightly until the and improve overall vehicle performance. This system transmission cools down enough to allow a return to the can also provide you with more control during passing, requested speed.
Page 345 STARTING AND OPERATING 343 condition would result. It will remain in the selected gear • If a requested downshift would cause the engine to until another upshift or downshift is chosen, except as overspeed, that shift will not occur. described below: •...
Page 346: Autostick (Cvt)
344 STARTING AND OPERATING Operation WARNING! NOTE: AutoStick is not available until the CVT warms Do not downshift for additional engine braking on a up in cold weather. slippery surface. The drive wheels could lose their When the shift lever is in the DRIVE position, AutoStick grip and the vehicle could skid, causing a collision or is activated by moving the shift lever side-to-side.
Page 347 STARTING AND OPERATING 345 In AutoStick mode, the transmission will shift up or • Transmission shifting will be more noticeable when down when (+/-) is manually selected by the driver, AutoStick is engaged. unless an engine lugging or overspeed condition would •...
Page 348: Four-Wheel Drive Operation - If Equipped
346 STARTING AND OPERATING traction surfaces, activate the “4WD LOCK” switch by FOUR-WHEEL DRIVE OPERATION — IF pulling up once and releasing. This locks the center EQUIPPED coupling allowing more torque to be sent to the rear This feature provides full time, on-demand, four–wheel wheels.
Page 349: Off-Road Driving Tips
STARTING AND OPERATING 347 An advantage of the higher ground clearance is a better and maintain a good driving posture. Avoid sudden view of the road, allowing you to anticipate problems. accelerations, turns or braking. In most cases there are no They are not designed for cornering at the same speeds as road signs, posted speed limits or signal lights.
Page 350: When To Use Low (L Off-Road) With The 4Wd Lock Lever Engaged
348 STARTING AND OPERATING NOTE: For maximum off-road performance, premium WARNING! fuel is recommended. While the vehicle will operate on regular fuel when in L Off-Road mode, the engine has Always wear your seat belt and firmly tie down been calibrated for maximum performance using pre- cargo.
Page 351 STARTING AND OPERATING 349 a lower gear than necessary to maintain headway. Over- turning your steering wheel no more than a 1/4 turn revving the engine can spin the wheels and traction will quickly back and forth for additional traction. Mud holes be lost.
Page 352: Hill Climbing
350 STARTING AND OPERATING use low (L Off-Road) with the 4WD LOCK engaged and Hills can cause serious problems. Some are just too steep ESC turned off. Reduced tire pressure will drastically to climb and should not be attempted. You should always improve your traction and handling, while driving on the feel confident with the vehicle and your abilities.
Page 353 STARTING AND OPERATING 351 Driving Up Hill back straight down the grade using engine resistance along with the vehicle brakes. Once you have determined your ability to proceed and have shifted into the appropriate gear, line your vehicle WARNING! up for the straightest possible run. Accelerate with an easy constant throttle and apply more power as you start Never attempt to climb a hill at an angle or turn up the hill.
Page 354 352 STARTING AND OPERATING and proceed with caution. Allow engine and hill descent WARNING! braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock. Driving across an incline increases the risk of a rollover, which may result in severe injury.
Page 355: Driving Through Water
STARTING AND OPERATING 353 water into the engine air intake. If the engine stalls, do WARNING! (Continued) not attempt to restart it. Determine if it has ingested tipping and rolling the vehicle, which may result in water first. The key to any crossing is low and slow. You severe injury.
Page 356: After Driving Off-Road
354 STARTING AND OPERATING Before You Cross Any Type Of Water types normally contain hidden obstacles and make it difficult to determine an accurate water depth, approach As you approach any type of water, you need to deter- angle, and bottom condition. Murky or muddy water mine if you can cross it safely and responsibly.
Page 357 STARTING AND OPERATING 355 always a good idea to check for damage. That way you • After extended operation in mud, sand, water, or can get any problems taken care of right away and have similar dirty conditions, have the radiator, fan, brake your vehicle ready when you need it.
Page 358: Power Steering
356 STARTING AND OPERATING system. This noise should be considered normal, and it POWER STEERING does not in any way damage the steering system. The standard power steering system will give you good vehicle response and increased ease of maneuverability CAUTION! in tight spaces.
Page 359: Parking Brake
STARTING AND OPERATING 357 If necessary, add fluid to restore to the proper indicated CAUTION! level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Do not use chemical flushes in your power steering Parts”...
Page 360 358 STARTING AND OPERATING NOTE: • When the parking brake is applied and the automatic transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle.
Page 361 STARTING AND OPERATING 359 WARNING! WARNING! (Continued) • Always fully apply the parking brake when leav- • When leaving the vehicle, always remove the Key ing your vehicle or it may roll and cause damage or Fob from the ignition and lock your vehicle. injury.
Page 362: Brake System
360 STARTING AND OPERATING If either of the two hydraulic systems lose normal capa- BRAKE SYSTEM bility, the remaining system will still function with some Your vehicle is equipped with power assisted brakes as loss of overall braking effectiveness. This will be evident standard equipment.
Page 363: Electronic Brake Control System
STARTING AND OPERATING 361 ELECTRONIC BRAKE CONTROL SYSTEM WARNING! Your vehicle may be equipped with an optional ad- • Pumping of the anti-lock brakes will diminish vanced electronic brake control system that includes their effectiveness and may lead to a collision. Anti-Lock Brake System (ABS), Traction Control System Pumping makes the stopping distance longer.
Page 364 362 STARTING AND OPERATING If the “ABS Warning Light” is on, the brake system WARNING! (Continued) should be serviced as soon as possible to restore the • The capabilities of an ABS-equipped vehicle must benefits of anti-lock brakes. If the “ABS Warning Light” never be exploited in a reckless or dangerous does not come on when the ignition switch is turned to manner which could jeopardize the user’s safety or...
Page 365: Traction Control System (Tcs)
STARTING AND OPERATING 363 ABS is activated during braking under certain road or WARNING! stopping conditions. ABS-inducing conditions can in- clude ice, snow, gravel, bumps, railroad tracks, loose The Anti-Lock Brake System (ABS) contains sophis- debris, or panic stops. ticated electronic equipment that may be susceptible to interference caused by improperly installed or You may also experience the following when the brake high output radio transmitting equipment.
Page 366: Brake Assist System (Bas)
364 STARTING AND OPERATING a limited slip differential and controls the wheel spin benefit of the system, you must apply continuous brak- across a driven axle. If one wheel on a driven axle is ing pressure during the stopping sequence (do not spinning faster than the other, the system will apply the “pump”...
Page 367: Electronic Roll Mitigation (Erm)
STARTING AND OPERATING 365 NOTE: Anytime the ESC system is in the “Full Off” Electronic Roll Mitigation (ERM) mode, ERM is disabled. Refer to “Electronic Stability This system anticipates the potential for wheel lift by Control (ESC)” in this section for a complete explanation monitoring the driver’s steering wheel input and the of the available ESC modes.
Page 368: Hill Descent Control (Hdc) - If Equipped
366 STARTING AND OPERATING Off” button for five seconds. Refer to “Electronic Stability Hill Descent Control (HDC) — If Equipped Control (ESC)” in this section of the manual. This system maintains vehicle speed while descending hills during off-road driving situations. HDC will auto- HDC operation can be overridden with brake application matically apply the brakes to control downhill speed to to slow the vehicle down below the HDC control speed.
Page 369: Hill Start Assist (Hsa)
STARTING AND OPERATING 367 HSA Activation Criteria WARNING! The following criteria must be met in order for HSA to HDC is only intended to assist the driver in control- activate: ling vehicle speed when descending hills. The driver • Vehicle must be stopped. must remain attentive to the driving conditions and is responsible for maintaining a safe vehicle speed.
Page 370 368 STARTING AND OPERATING 1. Center the steering wheel (front wheels pointing WARNING! (Continued) straight forward). Always remember the driver is responsible for brak- 2. Shift the transmission into NEUTRAL. ing the vehicle. 3. Apply the parking brake. Disabling/Enabling HSA 4.
Page 371: Electronic Stability Control (Esc)
STARTING AND OPERATING 369 9. Turn the ignition switch to the OFF position and then ESC applies the brake of the appropriate wheel to assist back to the ON position. If the sequence was com- in counteracting the over-steer or under-steer condition pleted properly, the “ESC Activation/Malfunction In- •...
Page 372 370 STARTING AND OPERATING Full On (Four-Wheel Drive Models) Or On (Two-Wheel WARNING! (Continued) Drive Models) • ESC cannot prevent accidents, including those re- This is the normal operating mode for ESC. Whenever sulting from excessive speed in turns, driving on the vehicle is started the ESC system will be in this “On”...
Page 373 STARTING AND OPERATING 371 To turn ESC on again, momentarily press the “ESC Off” WARNING! (Continued) switch. This will restore the normal “ESC On” mode of Indicator Light” will be illuminated. When in “Par- operation. tial Off” mode, the engine power reduction of TCS is NOTE: To improve the vehicle’s traction when driving disabled, and the enhanced vehicle stability offered with snow chains, or starting off in deep snow, sand or...
Page 374 372 STARTING AND OPERATING appear in the odometer. Press and release the Trip To turn ESC on again, momentarily press the “ESC Off” Odometer button located on the instrument cluster to switch. This will restore the “ESC On” mode of operation. clear this message.
Page 375: Esc Activation/Malfunction Indicator Light And Esc Off Indicator Light
STARTING AND OPERATING 373 flashes when TCS is active. If the “ESC Activation/ ESC Activation/Malfunction Indicator Light And Malfunction Indicator Light” begins to flash during ac- ESC OFF Indicator Light celeration, ease up on the accelerator and apply as little throttle as possible.
Page 376: Tire Safety Information
374 STARTING AND OPERATING TIRE SAFETY INFORMATION The “ESC OFF Indicator Light” indicates the Electronic Stability Control (ESC) is partially Tire Markings off or full off. 1 — U.S. DOT Safety Standards 4 — Maximum Load Code (TIN) 2 — Size Designation 5 —...
Page 377 STARTING AND OPERATING 375 NOTE: • LT (Light Truck) — Metric tire sizing is based on U.S. design standards. The size designation for LT-Metric • P (Passenger) — Metric tire sizing is based on U.S. tires is the same as for P-Metric tires except for the design standards.
Page 378 376 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 379 STARTING AND OPERATING 377 EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions –...
Page 380: Tire Identification Number (Tin)
378 STARTING AND OPERATING EXAMPLE: Maximum Load – Maximum load indicates the maximum load this tire is designed to carry Maximum Pressure – Maximum pressure indicates the maximum permissible cold tire inflation pressure for this tire Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire, however, the date code may only be on one side.
Page 381 STARTING AND OPERATING 379 EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 382: Tire Terminology And Definitions
380 STARTING AND OPERATING Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 383: Tire Loading And Tire Pressure
STARTING AND OPERATING 381 Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Example Tire Placard Location (B-Pillar) Example Tire Placard Location (Door) I n f o r ma t i o n P r o v i d e d b y :...
Page 384 382 STARTING AND OPERATING Tire And Loading Information Placard This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4.
Page 385 STARTING AND OPERATING 383 NOTE: Under a maximum loaded vehicle condition, Steps For Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occu- axles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or GAWRs, vehicle loading, and trailer towing, refer to XXX kg”...
Page 386 384 STARTING AND OPERATING 4. The resulting figure equals the available amount of NOTE: cargo and luggage load capacity. For example, if • If your vehicle will be towing a trailer, load from your “XXX” amount equals 1,400 lbs (635 kg) and there will trailer will be transferred to your vehicle.
Page 387 STARTING AND OPERATING 385 I n f o r ma t i o n P r o v i d e d b y :...
Page 388: Tires - General Information
386 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
Page 389: Tire Inflation Pressures
STARTING AND OPERATING 387 Fuel Economy WARNING! (Continued) Underinflated tires will increase tire rolling resistance • Unequal tire pressures from one side of the vehicle resulting in higher fuel consumption. to the other can cause the vehicle to drift to the right or left.
Page 390 388 STARTING AND OPERATING At least once a month: mile (1.6 km) after sitting for a minimum of three hours. The cold tire inflation pressure must not exceed the • Check and adjust tire pressure with a good quality maximum inflation pressure molded into the tire side- pocket-type pressure gauge.
Page 391: Tire Pressures For High Speed Operation
STARTING AND OPERATING 389 Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) WARNING! during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. High speed driving with your vehicle under maxi- mum load is dangerous.
Page 392: Tire Types
390 STARTING AND OPERATING Tire Repair Tire Types If your tire becomes damaged, it may be repaired if it All Season Tires — If Equipped meets the following criteria: All Season tires provide traction for all seasons (spring, • The tire has not been driven on when flat. summer, fall and winter).
Page 393 STARTING AND OPERATING 391 Summer tires do not contain the all season designation or Snow Tires mountain/snowflake symbol on the tire sidewall. Use Some areas of the country require the use of snow tires summer tires only in sets of four; failure to do so may during the winter.
Page 394: Run Flat Tires - If Equipped
392 STARTING AND OPERATING While studded tires improve performance on ice, skid See the tire pressure monitoring section for more infor- and traction capability on wet or dry surfaces may be mation. poorer than that of non-studded tires. Some states pro- Spare Tires —...
Page 395 STARTING AND OPERATING 393 equipment tire and wheel found on the front or rear axle Since this tire has limited tread life, the original equip- of your vehicle. This spare tire may be used in the tire ment tire should be repaired (or replaced) and reinstalled rotation for your vehicle.
Page 396 394 STARTING AND OPERATING Full Size Spare — If Equipped your original equipment tire, replace (or repair) the original equipment tire and reinstall on the vehicle at the The full size spare is for temporary emergency use only. first opportunity. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not.
Page 397: Tire Spinning
STARTING AND OPERATING 395 Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires spin your vehicle’s wheels above 30 mph (48 km/h) or to help you in determining when your tires should be for longer than 30 seconds continuously without stop- replaced.
Page 398: Life Of Tire
396 STARTING AND OPERATING These indicators are molded into the bottom of the tread • Performance tires, tires with a speed rating of V or grooves. They will appear as bands when the tread depth higher, and summer tires typically have a reduced becomes a 1/16 of an inch (2 mm).
Page 399: Replacement Tires
STARTING AND OPERATING 397 It is recommended to replace the two front tires or two Replacement Tires rear tires as a pair. Replacing just one tire can seriously The tires on your new vehicle provide a balance of many affect your vehicle’s handling. If you ever replace a characteristics.
Page 400: Tire Chains (Traction Devices)
398 STARTING AND OPERATING WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 401: Tire Rotation Recommendations
STARTING AND OPERATING 399 The suggested rotation method is the “rearward cross” TIRE ROTATION RECOMMENDATIONS shown in the following diagram. This rotation pattern The tires on the front and rear of your vehicle operate at does not apply to some directional tires that must not be different loads and perform different steering, driving, reversed.
Page 402: Tire Pressure Monitoring System (Tpms)
400 STARTING AND OPERATING also increase as the vehicle is driven - this is normal and TIRE PRESSURE MONITORING SYSTEM (TPMS) there should be no adjustment for this increased pres- The Tire Pressure Monitor System (TPMS) will warn the sure. driver of a low tire pressure based on the vehicle recom- mended cold placard pressure.
Page 403 STARTING AND OPERATING 401 driven for up to 20 minutes above 15 mph (24 km/h) in CAUTION! order for the TPMS to receive this information. • The TPMS has been optimized for the original For example, your vehicle may have a recommended equipment tires and wheels.
Page 404: Base System
402 STARTING AND OPERATING Under-inflation also reduces fuel efficiency and tire CAUTION! (Continued) tread life, and may affect the vehicle’s handling and • After inspecting or adjusting the tire pressure, stopping ability. always reinstall the valve stem cap. This will •...
Page 405 STARTING AND OPERATING 403 The TPMS uses wireless technology with wheel rim audible chime will be activated when one or more of the mounted electronic sensors to monitor tire pressure lev- four active road tire pressures are low. Should this occur, els.
Page 406 404 STARTING AND OPERATING Pressure Monitoring Telltale Light will turn off when the 2. If you install the compact spare tire in place of a road fault condition no longer exists. A system fault can occur tire that has a pressure below the low-pressure warn- with any of the following scenarios: ing limit, upon the next ignition key cycle, a chime will sound and the Tire Pressure Monitoring Telltale Light...
Page 407: Premium System - If Equipped
STARTING AND OPERATING 405 long as no tire pressure is below the low-pressure • Three Trigger Modules (mounted in three of the four warning limit in any of the four active road tires. The wheel wells) vehicle may need to be driven for up to 20 minutes •...
Page 408 406 STARTING AND OPERATING the graphic display of the pressure value(s) will stop flashing, and the Tire Pressure Monitoring Light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this infor- mation.
Page 409 STARTING AND OPERATING 407 will be displayed instead of dashes. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2.
Page 410 408 STARTING AND OPERATING pressure values still shown. This indicates that the pres- 3. However, after driving the vehicle for up to 20 min- sure values are still being received from the TPM sensors utes above 15 mph (24 km/h), the Tire Pressure but they may not be located in the correct vehicle Monitoring Telltale Light will flash on and off for 75 position.
Page 411: General Information
STARTING AND OPERATING 409 long as no tire pressure is below the low-pressure FUEL REQUIREMENTS warning limit in any of the four active road tires. The 2.0L And 2.4L Engine vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to This engine is designed to meet all emis- receive this information.
Page 412: Reformulated Gasoline
410 STARTING AND OPERATING from operating with a heavy spark knock may void or CAUTION! not be covered by the New Vehicle Warranty. DO NOT use gasoline containing Methanol or gaso- Reformulated Gasoline line containing more than 10% Ethanol. Use of these Many areas of the country require the use of cleaner blends may result in starting and drivability prob- burning gasoline referred to as “Reformulated Gasoline.”...
Page 413: E-85 Usage In Non-Flex Fuel Vehicles
STARTING AND OPERATING 411 blended into some gasoline to increase octane. Gasoline E-85 Usage In Non-Flex Fuel Vehicles blended with MMT provides no performance advantage Non-Flex Fuel Vehicles (FFV) are compatible with gaso- beyond gasoline of the same octane number without line containing up to 10% ethanol (E10).
Page 414: Fuel System Cautions
412 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentrations performance: of methanol.
Page 415: Carbon Monoxide Warnings
STARTING AND OPERATING 413 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper main- WARNING! tenance. Have the exhaust system inspected every Carbon monoxide (CO) in exhaust gases is deadly. time the vehicle is raised. Have any abnormal Follow the precautions below to prevent carbon conditions repaired promptly.
Page 416 414 STARTING AND OPERATING After removing the gas cap, place the gas cap tether cable CAUTION! over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s • Damage to the fuel system or emission control surface.
Page 417: Loose Fuel Filler Cap Message
STARTING AND OPERATING 415 • If the gas cap is not tightened properly, the MIL will WARNING! (Continued) come on. Be sure the gas cap is tightened every time • Never add fuel when the engine is running. This is the vehicle is refueled.
Page 418: Vehicle Loading
416 STARTING AND OPERATING The bar code allows a computer scanner to read the VEHICLE LOADING Vehicle Identification Number (VIN). As required by National Highway Traffic Safety Admin- istration regulations, your vehicle has a certification label Gross Vehicle Weight Rating (GVWR) affixed to the driver’s side door or B-Pillar.
Page 419 STARTING AND OPERATING 417 Inflation Pressure The best way to figure out the total weight of your vehicle is to weigh it when it is fully loaded and ready for This is the cold tire inflation pressure for your vehicle for operation.
Page 420: Trailer Towing
418 STARTING AND OPERATING Common Towing Definitions CAUTION! The following trailer towing related definitions will assist Do not load your vehicle any heavier than the you in understanding the following information: GVWR. If you do, parts on your vehicle can break, or Gross Vehicle Weight Rating (GVWR) it can change the way your vehicle handles.
Page 421 STARTING AND OPERATING 419 The recommended way to measure GTW is to put your WARNING! fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. It is important that you do not exceed the maximum front or rear GAWR.
Page 422 420 STARTING AND OPERATING Frontal Area Weight-Carrying Hitch The frontal area is the maximum height multiplied by the A weight-carrying hitch supports the trailer tongue maximum width of the front of a trailer. weight, just as if it were luggage located at a hitch ball or some other connecting point of the vehicle.
Page 423 STARTING AND OPERATING 421 Weight-Distributing Hitch WARNING! A weight-distributing system works by applying lever- • An improperly adjusted Weight Distributing Hitch age through spring (load) bars. They are typically used system may reduce handling, stability, braking for heavier loads to distribute trailer tongue weight to the performance, and could result in a collision.
Page 424: Trailer Hitch Classification
422 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
Page 425: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 423 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Maximum GTW (Gross Maximum Tongue Wt. Engine/Transmission Frontal Area Trailer Wt.) (See Note) 2.0L Auto/Man 22 sq ft (2.04 sq m) 1,000 lbs (450 kg) 150 lbs (68 kg)
Page 426: Trailer And Tongue Weight
424 STARTING AND OPERATING NOTE: The trailer tongue weight must be considered as Never exceed the maximum tongue weight stamped on part of the combined weight of occupants and cargo, and your bumper or trailer hitch. should never exceed the weight referenced on the Tire and Loading Information placard.
Page 427: Towing Requirements
STARTING AND OPERATING 425 Consider the following items when computing the Towing Requirements weight on the rear axle of the vehicle: To promote proper break-in of your vehicle drivetrain • The tongue weight of the trailer. components, the following guidelines are recommended: •...
Page 428 426 STARTING AND OPERATING WARNING! WARNING! (Continued) • Safety chains must always be used between your Improper towing can lead to a collision. Follow these vehicle and trailer. Always connect the chains to guidelines to make your trailer towing as safe as the frame or hook retainers of the vehicle hitch.
Page 429 STARTING AND OPERATING 427 • Proper tire inflation pressures are essential to the safe WARNING! (Continued) and satisfactory operation of your vehicle. Refer to • Total weight must be distributed between the tow “Tires – General Information” in “Starting And Oper- vehicle and the trailer such that the following four ating”...
Page 430 428 STARTING AND OPERATING Towing Requirements — Trailer Brakes WARNING! • Do not interconnect the hydraulic brake system or • Do not connect trailer brakes to your vehicle’s vacuum system of your vehicle with that of the trailer. hydraulic brake lines. It can overload your brake This could cause inadequate braking and possible system and cause it to fail.
Page 431 STARTING AND OPERATING 429 CAUTION! (Continued) could lead to accelerated brake lining wear, higher brake pedal effort, and longer stopping distances. Towing Requirements — Trailer Lights And Wiring Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety.
Page 432: Towing Tips
430 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping, and backing up the trailer in an area located away from heavy traffic. Manual Transmission — If Equipped If using a manual transmission vehicle for trailer towing, all starts must be in first gear to avoid excessive clutch slippage.
Page 433 STARTING AND OPERATING 431 NOTE: Using a lower gear ratio while operating the AutoStick — If Equipped vehicle under heavy loading conditions, will improve When using the AutoStick shift control, select the highest performance and extend transmission life by reducing gear that allows for adequate performance and avoids excessive shifting and heat buildup.
Page 434 432 STARTING AND OPERATING Electronic Speed Control — If Equipped Cooling System To reduce potential for engine and transmission over- • Do not use in hilly terrain or with heavy loads. heating, take the following actions: • When using the speed control, if you experience speed City Driving drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed.
Page 435: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 433 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground Manual Transmission Automatic Transmission Flat Tow None • Transmission in NEU- NOT ALLOWED TRAL • Key in ACC Position Dolly Tow Front OK (FWD Only)
Page 436 434 STARTING AND OPERATING CAUTION! • DO NOT flat tow any vehicle equipped with an automatic transmission. Damage to the drivetrain will result. If these vehicles require towing, make sure all drive wheels are OFF the ground. • DO NOT dolly tow any 4WD vehicle. Internal damage to the transmission or transfer case will occur if a dolly is used when recreational towing.
Page 437 WHAT TO DO IN EMERGENCIES CONTENTS HAZARD WARNING FLASHERS ...437 ▫ Road Tire Installation ....449 IF YOUR ENGINE OVERHEATS .
Page 438 436 WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE ....468 ▫ With Ignition Key .....472 TOWING A DISABLED VEHICLE .
Page 439: Hazard Warning Flashers
WHAT TO DO IN EMERGENCIES 437 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate ac- tion.
Page 440: Wheel And Tire Torque Specifications
438 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! (Continued) to cool. Never try to open a cooling system pressure Driving with a hot cooling system could damage cap when the radiator or coolant bottle is hot. your vehicle. If the pointer rises to the H (red) mark, the instrument cluster will sound a chime.
Page 441 WHAT TO DO IN EMERGENCIES 439 **Use only your Authorized Dealer recommended lug Tighten the lug nuts/bolts in a star pattern until each nuts/bolts and clean or remove any dirt or oil before nut/bolt has been tightened twice. tightening. Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles.
Page 442: Jacking And Tire Changing
440 WHAT TO DO IN EMERGENCIES WARNING! WARNING! (Continued) • Being under a jacked-up vehicle is dangerous. The To avoid the risk of forcing the vehicle off the jack, vehicle could slip off the jack and fall on you. You do not tighten the lug nuts fully until the vehicle has could be crushed.
Page 443: Jack Location
WHAT TO DO IN EMERGENCIES 441 Jack Location Spare Tire Stowage The jack and jack-handle are stowed under the load floor The compact spare tire is stowed under the rear load floor in the cargo area. in the cargo area. Spare Tire Removal Lift up the load floor cover and remove the hold down.
Page 444: Jacking Instructions
442 WHAT TO DO IN EMERGENCIES 2. Turn on the Hazard Warning flasher. Jacking Instructions 3. Set the parking brake. WARNING! 4. Place the shift lever in PARK (automatic transmission) Carefully follow these tire changing warnings to or REVERSE (manual transmission). help prevent personal injury or damage to your 5.
Page 445 WHAT TO DO IN EMERGENCIES 443 WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a Jack Warning Label service center where it can be raised on a lift.
Page 446 444 WHAT TO DO IN EMERGENCIES NOTE: Refer to “Tires — General Information” in “Start- ing And Operating” for further information about the spare tire, it’s use, and operation. 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench and remove the wrench from the jack assembly.
Page 447 WHAT TO DO IN EMERGENCIES 445 assembly. The rear location is the same but with two rectangular cutouts. For vehicles equipped with plastic trim, the plastic has been cut away to expose the jacking locations in the body. Removing Jack Handle From Jack 2.
Page 448 446 WHAT TO DO IN EMERGENCIES jack head is properly engaged with the lift area closest to the wheel to be changed. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it.
Page 449 WHAT TO DO IN EMERGENCIES 447 WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle has been lowered. Failure to follow this warning may result in serious injury. Mounting Spare Tire CAUTION! Be sure to mount the spare tire with the valve stem...
Page 450 448 WHAT TO DO IN EMERGENCIES correctly, have them checked with a torque wrench by WARNING! your authorized dealer or service station. To avoid possible personal injury, handle the wheel 8. Remove the wheel blocks and lower the jack until it is covers with care to avoid contact with any sharp free.
Page 451: Road Tire Installation
WHAT TO DO IN EMERGENCIES 449 WARNING! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immedi- ately. 10. Check the spare tire pressure as soon as possible. Correct the tire pressure as required.
Page 452 450 WHAT TO DO IN EMERGENCIES 3. Install the five wheel lug nuts with the cone shaped 6. After 25 miles (40 km) check the lug nut torque with a end of the nut toward the wheel. Lightly tighten the torque wrench to ensure that all lug nuts are properly lug nuts.
Page 453: Tire Service Kit - If Equipped
WHAT TO DO IN EMERGENCIES 451 3. Lower the vehicle to the ground by turning the jack TIRE SERVICE KIT — IF EQUIPPED handle counterclockwise. Small punctures up to ¼” (6 mm) in the tire tread can be sealed with Tire Service Kit. Foreign objects (e.g., screws 4.
Page 454: Tire Service Kit Components And Operation
452 WHAT TO DO IN EMERGENCIES Using The Mode Select Knob And Hoses Tire Service Kit Components And Operation Your Tire Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob (5) and turn to this position for air pump operation only.
Page 455: Tire Service Kit Usage Precautions
WHAT TO DO IN EMERGENCIES 453 Using The Power Button Push and release the Power Button (4) once to turn On the Tire Service Kit. Push and release the Power Button (4) again to turn Off the Tire Service Kit. Using The Deflation Button Push the Deflation Button (2) to reduce the air pressure in the tire if it becomes over-inflated.
Page 456 454 WHAT TO DO IN EMERGENCIES from the vehicle or tire and wheel components. Once WARNING! the sealant dries, it can easily be peeled off and properly discarded. • Do not attempt to seal a tire on the side of the vehicle closest to traffic.
Page 457: Sealing A Tire With Tire Service Kit
WHAT TO DO IN EMERGENCIES 455 WARNING! (Continued) WARNING! (Continued) • Keep Tire Service Kit away from open flames or • Tire Service Kit Sealant solution contains latex. In heat source. case of an allergic reaction or rash, consult a phy- •...
Page 458 456 WHAT TO DO IN EMERGENCIES on the ground. This will provide the best positioning 4. Remove the cap from the valve stem and then screw of the kit when injecting the sealant into the deflated the fitting at the end of the Sealant Hose (6) onto the tire and running the air pump.
Page 459 WHAT TO DO IN EMERGENCIES 457 NOTE: Sealant may leak out through the puncture in the NOTE: If the Mode Select Knob (5) is on Air Mode and tire. the pump is operating, air will dispense from the Air Pump Hose (7) only, not the Sealant Hose (6). If the sealant (white fluid) does not flow within 0 –...
Page 460 458 WHAT TO DO IN EMERGENCIES latch pillar (recommended pressure). Check the tire 3. Immediately disconnect the Sealant Hose (6) from the pressure by looking at the Pressure Gauge (3). valve stem, reinstall the cap on the fitting at the end of the hose, and place the Tire Service Kit in the vehicle If the tire does not inflate to at least 26 psi (1.8 Bar) storage location.
Page 461 WHAT TO DO IN EMERGENCIES 459 (D) Drive Vehicle: (E) After Driving: Immediately after injecting sealant and inflating the tire, Pull over to a safe location. Refer to “Whenever You Stop drive the vehicle 5 miles (8 km) or 10 minutes to ensure to Use Tire Service Kit”...
Page 462 460 WHAT TO DO IN EMERGENCIES If tire pressure is less than 19 psi (1.3 Bar): 4. Have the tire inspected and repaired or replaced at the earliest opportunity at an authorized dealer or tire The tire is too badly damaged. Do not attempt to drive service center.
Page 463: Jump-Starting Procedures
WHAT TO DO IN EMERGENCIES 461 3. Push the Sealant Bottle release button. The Sealant JUMP-STARTING PROCEDURES Bottle (1) will pop up. Remove the bottle and dispose If your vehicle has a discharged battery it can be jump- of it accordingly. started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster 4.
Page 464: Preparations For Jump-Start
462 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations For Jump-Start The battery in your vehicle is located in the front of the engine compartment below the air intake duct.
Page 465 WHAT TO DO IN EMERGENCIES 463 WARNING! • Take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact.
Page 466: Jump-Starting Procedure
464 WHAT TO DO IN EMERGENCIES 1. Set the parking brake, shift the automatic transmission Jump-Starting Procedure into PARK (manual transmission to NEUTRAL) and turn the ignition to LOCK. WARNING! 2. Turn off the heater, radio, and all unnecessary electri- Failure to follow this jump-starting procedure could cal accessories.
Page 467 WHAT TO DO IN EMERGENCIES 465 Connecting The Jumper Cables WARNING! 1. Connect the positive (+) end of the jumper cable to the Do not connect the jumper cable to the negative (-) positive (+) post of the discharged vehicle. post of the discharged battery.
Page 468: Freeing A Stuck Vehicle
466 WHAT TO DO IN EMERGENCIES 6. Once the engine is started, remove the jumper cables If frequent jump-starting is required to start your vehicle in the reverse sequence: you should have the battery and charging system in- spected at your authorized dealer. Disconnecting The Jumper Cables 1.
Page 469 WHAT TO DO IN EMERGENCIES 467 and REVERSE (with automatic transmission) or 2nd gear NOTE: Push the ESC Off switch, to place the Electronic and REVERSE (with manual transmission), while gently Stability Control (ESC) system in Partial Off mode, pushing the accelerator. Use the least amount of accelera- before rocking the vehicle.
Page 470 468 WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE WARNING! If a malfunction occurs and the shift lever cannot be Fast spinning tires can be dangerous. Forces gener- moved out of the PARK position, you can use the ated by excessive wheel speeds may cause damage, or following procedure to temporarily move the shift lever: even failure, of the axle and tires.
Page 471 WHAT TO DO IN EMERGENCIES 469 4. Turn the ignition switch to the ACC or ON/RUN position, but do not start the engine. 5. Push and maintain firm pressure on the brake pedal. 6. Insert the screwdriver or similar tool into the access port, and push and hold the override release lever forward.
Page 472 470 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. I n f o r ma t i o n P r o v i d e d b y :...
Page 473 WHAT TO DO IN EMERGENCIES 471 6-Speed Auto- Towing Wheels OFF Manual 6-Speed Automatic matic (FWD Automatic Condition the Ground Transmission Only) Transmission Flat Tow NONE • Transmis- If transmission is If transmission is op- NOT AL- sion operable: erable: LOWED NEU- •...
Page 474 472 WHAT TO DO IN EMERGENCIES Front Wheel Drive (FWD) models (with 6-speed auto- With Ignition Key matic only) may also be towed (under the same limita- Automatic Transmission tions shown above) with the rear wheels elevated. • Front Wheel Drive (FWD) vehicles can be towed with the front wheels elevated, or on a flatbed truck (all four CAUTION! wheels OFF the ground).
Page 475 WHAT TO DO IN EMERGENCIES 473 Manual Transmission CAUTION! • Front Wheel Drive (FWD) or Four-Wheel Drive (4WD) • DO NOT flat tow any disabled vehicle if condition vehicles can be flat towed (all four wheels on the is related to the clutch, transmission or driveline. ground) with the transmission in NEUTRAL.
Page 476 474 WHAT TO DO IN EMERGENCIES All Transmissions Without The Ignition Key If you must use the accessories (wipers, defroster, etc.) Special care must be taken when the vehicle is towed while being towed, the key must be in the ON/RUN with the ignition in the LOCK/OFF position.
Page 477 MAINTAINING YOUR VEHICLE CONTENTS ENGINE COMPARTMENT — 2.0L ..477 ▫ Engine Oil Filter ..... .486 ENGINE COMPARTMENT —...
Page 478 476 MAINTAINING YOUR VEHICLE ▫ Automatic Transmission (Six-Speed) — If REPLACEMENT BULBS ....522 Equipped ......504 BULB REPLACEMENT .
Page 479: Engine Compartment - 2.0L
MAINTAINING YOUR VEHICLE 477 ENGINE COMPARTMENT — 2.0L 1 — Washer Fluid Reservoir 6 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 7 — Coolant Pressure Cap 3 — Engine Oil Fill 8 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 9 —...
Page 480: Engine Compartment - 2.4L
478 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.4L 1 — Washer Fluid Reservoir 6 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 7 — Coolant Pressure Cap 3 — Engine Oil Fill 8 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 9 —...
Page 481: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 479 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors further damage to the emission control system. It the performance of the emissions, engine, and automatic could also affect fuel economy and driveability.
Page 482: Emissions Inspection And Maintenance Programs
480 MAINTAINING YOUR VEHICLE persists, the message will appear the next time the Normally, the OBD II system will be ready. The OBD II vehicle is started. This might indicate a damaged cap. If system may not be ready if your vehicle was recently the problem is detected twice in a row, the system will serviced, recently had a dead battery or a battery replace- turn on the MIL.
Page 483: Replacement Parts
MAINTAINING YOUR VEHICLE 481 3. Approximately 15 seconds later, one of two things will system to update. A recheck with the above test routine happen: may then indicate that the system is now ready. • The MIL will flash for about 10 seconds and then Regardless of whether your vehicle’s OBD II system is return to being fully illuminated until you turn OFF ready or not, if the MIL is illuminated during normal...
Page 484: Dealer Service
482 MAINTAINING YOUR VEHICLE DEALER SERVICE WARNING! (Continued) Your authorized dealer has the qualified service person- have the knowledge and the proper equipment. If nel, special tools, and equipment to perform all service you have any doubt about your ability to perform a operations in an expert manner.
Page 485: Engine Oil
MAINTAINING YOUR VEHICLE 483 Engine Oil CAUTION! Checking Oil Level • Failure to properly maintain your vehicle or per- To assure proper engine lubrication, the engine oil must form repairs and service when necessary could be maintained at the correct level. Check the oil level at result in more costly repairs, damage to other regular intervals, such as every fuel stop.
Page 486 484 MAINTAINING YOUR VEHICLE low end of the indicated range will result in the oil level Engine Oil Selection at the full end of the indicator range. For best performance and maximum protection under all types of operating conditions, the manufacturer only CAUTION! recommends engine oils that are API Certified and meet the requirements of Chrysler Material Standard MS-6395.
Page 487 MAINTAINING YOUR VEHICLE 485 Synthetic Engine Oils CAUTION! You may use synthetic engine oils provided the recom- Do not use chemical flushes in your engine oil as the mended oil quality requirements are met, and the recom- chemicals can damage your engine. Such damage is mended maintenance intervals for oil and filter changes not covered by the New Vehicle Limited Warranty.
Page 488: Engine Oil Filter
486 MAINTAINING YOUR VEHICLE station or governmental agency for advice on how and WARNING! where used oil and oil filters can be safely discarded in your area. The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine Engine Oil Filter backfire.
Page 489: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 487 Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. • Battery gas is flammable and explosive. Keep You will never have to add water, nor is periodic main- flame or sparks away from the battery. Do not use tenance required.
Page 490: Air Conditioner Maintenance
488 MAINTAINING YOUR VEHICLE the condenser fins and a performance test. Drive belt tension CAUTION! should also be checked at this time. • It is essential when replacing the cables on the battery that the positive cable is attached to the WARNING! positive post and the negative cable is attached to •...
Page 491 MAINTAINING YOUR VEHICLE 489 A/C Air Filter CAUTION! Refer to the “Maintenance Schedule” for the proper Do not use chemical flushes in your air conditioning maintenance intervals. system as the chemicals can damage your air condi- tioning components. Such damage is not covered by WARNING! the New Vehicle Limited Warranty.
Page 492: Body Lubrication
490 MAINTAINING YOUR VEHICLE 4. Disengage the two retaining tabs that secure the filter cover, make sure the retaining tabs fully engage the cover to the HVAC housing, and remove the cover. cover. CAUTION! The A/C air filter is identified with an arrow to indicate airflow direction through the filter.
Page 493: Windshield Wiper Blades
MAINTAINING YOUR VEHICLE 491 should be wiped clean to remove dust and grit; after Operation of the wipers on dry glass for long periods lubricating excess oil and grease should be removed. may cause deterioration of the wiper blades. Always use Particular attention should also be given to hood latching washer fluid when using the wipers to remove salt or dirt components to ensure proper function.
Page 494: Exhaust System
492 MAINTAINING YOUR VEHICLE When refilling the washer fluid reservoir, take some Exhaust System washer fluid and apply it to a cloth or towel and wipe The best protection against carbon monoxide entry into clean the wiper blades, this will help blade performance. the vehicle body is a properly maintained engine exhaust To prevent freeze-up of your windshield washer system system.
Page 495 MAINTAINING YOUR VEHICLE 493 WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions control and can eventually poison you.
Page 496 494 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
Page 497: Cooling System
MAINTAINING YOUR VEHICLE 495 Coolant Checks Cooling System Check engine coolant (antifreeze) protection every 12 WARNING! months (before the onset of freezing weather, where applicable). If the engine coolant (antifreeze) is dirty or • When working near the radiator cooling fan, rusty in appearance, the system should be drained, disconnect the fan motor lead or turn the ignition flushed, and refilled with fresh engine coolant (anti-...
Page 498 496 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush And Refill CAUTION! NOTE: Some vehicles require special tools to add coolant • Mixing of engine coolant (antifreeze) other than properly. Failure to fill these systems properly could lead specified Organic Additive Technology (OAT) en- to severe internal engine damage.
Page 499 MAINTAINING YOUR VEHICLE 497 you use the same engine coolant (OAT coolant conform- CAUTION! (Continued) ing to MS.90032) throughout the life of your vehicle. • Do not use water alone or alcohol-based engine Please review these recommendations for using Organic coolant (antifreeze) products.
Page 500 498 MAINTAINING YOUR VEHICLE (antifreeze) solution. The use of lower quality water • Mixing engine coolant (antifreeze) types is not recom- will reduce the amount of corrosion protection in the mended and can result in cooling system damage. If engine cooling system. HOAT and OAT coolant are mixed in an emergency, have a authorized dealer drain, flush, and refill with Please note that it is the owner’s responsibility to main-...
Page 501 MAINTAINING YOUR VEHICLE 499 rules for your community. To prevent ingestion by ani- WARNING! mals or children, do not store ethylene glycol-based engine coolant in open containers or allow it to remain in • The warning words “DO NOT OPEN HOT” on the puddles on the ground.
Page 502 500 MAINTAINING YOUR VEHICLE long as the engine operating temperature is satisfactory, • Do not overfill the coolant expansion bottle. the coolant bottle need only be checked once a month. • Check the coolant freeze point in the radiator and in the coolant expansion bottle.
Page 503: Brake System
MAINTAINING YOUR VEHICLE 501 • Keep the front of the radiator clean. If your vehicle is WARNING! equipped with air conditioning, keep the front of the condenser clean. Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or •...
Page 504 502 MAINTAINING YOUR VEHICLE when the pads are replaced. However, low fluid level WARNING! may be caused by a leak and a checkup may be needed. • Use only manufacturer’s recommended brake NOTE: If your vehicle is equipped with a manual trans- fluid.
Page 505 MAINTAINING YOUR VEHICLE 503 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contaminate moisture, use only new brake fluid or fluid that has the brake fluid. Brake seal components could be been in a tightly closed container.
Page 506: Maintaining Your Vehicle
504 MAINTAINING YOUR VEHICLE Automatic Transmission (Six-Speed) — If CAUTION! (Continued) Equipped in transmission shift quality and/or torque converter Selection Of Lubricant (Six-Speed Transmission) shudder. Refer to “Fluids, Lubricants, and Genuine Parts” in this section for fluid specifications. It is important to use the proper transmission fluid to ensure optimum transmission performance and life.
Page 507 MAINTAINING YOUR VEHICLE 505 CAUTION! CAUTION! Do not use chemical flushes in your transmission as If a transmission fluid leak occurs, visit your autho- the chemicals can damage your transmission compo- rized dealer immediately. Severe transmission dam- nents. Such damage is not covered by the New age may occur.
Page 508: Automatic Transmission (Cvt) - If Equipped
506 MAINTAINING YOUR VEHICLE Automatic Transmission (CVT) — If Equipped CAUTION! Selection Of Lubricant (CVT) Using a transmission fluid other than the manufac- It is important to use the proper transmission fluid to turer’s recommended fluid may cause belt slip and ensure optimum transmission performance and life.
Page 509 MAINTAINING YOUR VEHICLE 507 an improper fluid level can cause severe transmission CAUTION! damage. Do not use chemical flushes in your transmission as CAUTION! the chemicals can damage your transmission compo- nents. Such damage is not covered by the New If a transmission fluid leak occurs, visit your autho- Vehicle Limited Warranty.
Page 510: Manual Transmission - If Equipped
508 MAINTAINING YOUR VEHICLE NOTE: If contaminated with water, the fluid should be Manual Transmission — If Equipped changed immediately. Lubricant Selection Rear Drive Assembly (RDA) — AWD/4WD Models Use only the manufacturers recommended transmission Only fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle”...
Page 511: Power Transfer Unit (Ptu) - Awd/4Wd Models Only
MAINTAINING YOUR VEHICLE 509 Frequency Of Fluid Change Frequency Of Fluid Change Refer to the “Maintenance Schedule” for the proper Refer to the “Maintenance Schedule” for the proper maintenance intervals. maintenance intervals. Power Transfer Unit (PTU) — AWD/4WD Models Appearance Care And Protection From Corrosion Only Protection Of Body And Paint From Corrosion Lubricant Selection...
Page 512 510 MAINTAINING YOUR VEHICLE The following maintenance recommendations will enable Washing you to obtain maximum benefit from the corrosion • Wash your vehicle regularly. Always wash your ve- resistance built into your vehicle. hicle in the shade using MOPAR® Car Wash, or a mild car wash soap, and rinse the panels completely with What Causes Corrosion? clear water.
Page 513 MAINTAINING YOUR VEHICLE 511 • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will •...
Page 514 512 MAINTAINING YOUR VEHICLE Wheel And Wheel Trim Care CAUTION! • All wheels and wheel trim, especially aluminum and Do not use scouring pads, steel wool, a bristle brush, chrome plated wheels, should be cleaned regularly or metal polishes. Do not use oven cleaner. These with a mild soap and water to prevent corrosion.
Page 515 MAINTAINING YOUR VEHICLE 513 • For tough stains, apply MOPAR® Total Clean, or a Your leather upholstery can be best preserved by regular mild soap solution to a clean, damp cloth and remove cleaning with a damp soft cloth. Small particles of dirt stain.
Page 516 514 MAINTAINING YOUR VEHICLE Glass Surfaces CAUTION! All glass surfaces should be cleaned on a regular basis Do not use Alcohol and Alcohol-based and/or Keton with MOPAR® Glass Cleaner, or any commercial based cleaning products to clean leather seats, as household-type glass cleaner.
Page 517 MAINTAINING YOUR VEHICLE 515 Instrument Panel Bezels 1. Clean with a wet soft rag. A mild soap solution may be used, but do not use high alcohol content or abrasive CAUTION! cleaners. If soap is used, wipe clean with a clean damp rag.
Page 518: Fuses
516 MAINTAINING YOUR VEHICLE FUSES WARNING! WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system • When replacing a blown fuse, always use an ap- periodically, checking for cuts, frays, or loose parts. propriate replacement fuse with the same amp Damaged parts must be replaced immediately.
Page 519: Integrated Power Module (Ipm)
MAINTAINING YOUR VEHICLE 517 WARNING! (Continued) • If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, gearbox system) or steering system blows, contact an authorized dealer. Integrated Power Module (IPM) The Integrated Power Module is located in the engine compartment near the air cleaner assembly.
Page 520 518 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description 10 Amp Red Rear Center Brake Light Switch 10 Amp Red Ignition Switch/Occupant Classification Module 15 Amp Lt Blue Battery Feed For Power Tech 10 Amp Red Power Mirror/Steering Con- trol Satellite Radio/Hands- Free Phone 30 Amp Green Ignition Off Draw...
Page 521 MAINTAINING YOUR VEHICLE 519 Cavity Cartridge Fuse Mini-Fuse Description 20 Amp Yellow Cigar Lighter 10 Amp Red Instrument Cluster 40 Amp Green Radiator Fan 15 Amp Lt Blue Dome Lamp/Sunroof/Rear Wiper Motor 10 Amp Red Wireless Control Module 40 Amp Green Auto Shutdown Relay 20 Amp Yellow Radio Amplifiers...
Page 522 520 MAINTAINING YOUR VEHICLE Cavity Cartridge Fuse Mini-Fuse Description 15 Amp Lt Blue Auto Shutdown Relay 10 Amp Red Airbag Control Module 10 Amp Red Airbag Control Module/ Occupant Classification Mod- Hot Car (No Fuse Required) 20 Amp Yellow Heated Seat – If Equipped 10 Amp Red Headlamp Washer –...
Page 523 MAINTAINING YOUR VEHICLE 521 Cavity Cartridge Fuse Mini-Fuse Description 30 Amp Pink Headlamp/Washer Control/ Smart Glass – If Equipped 25 Amp Clear Diesel Heater and H2/MOD power top CAUTION! CAUTION! (Continued) • When replacing a blown fuse, it is important to use •...
Page 524: Vehicle Storage
522 MAINTAINING YOUR VEHICLE • Anytime you store your vehicle, or keep it out of VEHICLE STORAGE service (i.e., vacation) for two weeks or more, run the If you will not be using your vehicle for more than 21 air conditioning system at idle for about five minutes days, you may want to take steps to preserve your in the fresh air and high blower setting.
Page 525 MAINTAINING YOUR VEHICLE 523 Interior Bulbs Bulb Number Front Header Lamp T578 Center Dome Lamp T578 Rear Cargo Lamp/Flashlight 8–A35LF Exterior Bulbs Bulb Number Low Beam/High Beam Headlamp Front Park/Turn Signal/Side Marker Lamp 3757KA Front Fog Lamp PSX24W Center High Mounted Stop Lamp (CHMSL) LED Assembly (Serviced At Authorized Dealer) Rear Tail/Turn/Stop Lamp 3157...
Page 526: Bulb Replacement
524 MAINTAINING YOUR VEHICLE NOTE: These are halogen bulbs. Take care not to touch BULB REPLACEMENT the bulb with your fingers. Body oils from your fingers NOTE: Lens fogging can occur under certain atmo- could cause excessive heat buildup which reduces bulb spheric conditions.
Page 527: Rear Tail, Turn Signal And Backup Lamps
MAINTAINING YOUR VEHICLE 525 Rear Tail, Turn Signal And Backup Lamps License Lamps 1. Raise the liftgate. 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate. 2. Remove the two push-pins from the taillamp housing. 2.
Page 528: Fluid Capacities
526 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) 13.6 Gallons 51 Liters Engine Oil with Filter 2.0L and 2.4L Engine (SAE 5W-20, 4.5 Quarts 4.26 Liters API Certified) Cooling System * 2.0L and 2.4L Engine (MOPAR® 7.2 Quarts 6.8 Liters Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula or...
Page 529: Fluids, Lubricants And Genuine Parts
MAINTAINING YOUR VEHICLE 527 FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Chrysler Material Standard MS.90032. Engine Oil We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Ma-...
Page 530 528 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! (Continued) • Do not use water alone or alcohol-based engine • Mixing of engine coolant (antifreeze) other than coolant (antifreeze) products. Do not use additional specified Organic Additive Technology (OAT) en- rust inhibitors or antirust products, as they may not gine coolant (antifreeze), may result in engine be compatible with the radiator engine coolant and damage and may decrease corrosion protection.
Page 531: Chassis
MAINTAINING YOUR VEHICLE 529 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission (CVT) — If Use only MOPAR® CVTF+4® Continuously Variable Transmission Fluid or Equipped equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Automatic Transmission (Six-Speed) Use only MOPAR®...
Page 532 I n f o r ma t i o n P r o v i d e d b y :...
Page 533: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS MAINTENANCE SCHEDULE ....532 ▫ Maintenance Chart.....534 I n f o r ma t i o n P r o v i d e d b y :...
Page 534 532 MAINTENANCE SCHEDULES On Non-EVIC equipped vehicles, “Change Oil” will flash MAINTENANCE SCHEDULE in the instrument cluster odometer and a single chime Your vehicle is equipped with an automatic oil change will sound, indicating that an oil change is necessary. indicator system.
Page 535 MAINTENANCE SCHEDULES 533 Once A Month Or Before A Long Trip: At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Check engine oil level • Change oil and filter. • Check windshield washer fluid level • Rotate the tires. Rotate at the first sign of irregu- •...
Page 536 534 MAINTENANCE SCHEDULES Maintenance Chart Refer to the Maintenance Schedules on the following pages for the required maintenance intervals. Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, boot seals. tie rod ends, and replace if necessary.
Page 537 MAINTENANCE SCHEDULES 535 Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Additional Maintenance Replace engine air cleaner filter. Replace air conditioning/cabin air filter. Replace spark plugs** Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first.
Page 538 536 MAINTENANCE SCHEDULES Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Change the automatic transmission fluid and filter. (CVT only) Change the automatic transmission fluid and filter (six-speed only) if you frequently drive: on rough or unpaved roads, on mountain roads, on short trips, in heavy city traffic during hot weather, or if you use the vehicle for police, taxi, fleet, or frequent...
Page 539 MAINTENANCE SCHEDULES 537 Mileage or time passed (whichever comes first) Or Years: 2 Or Kilometers: Change the manual transmission fluid if using your vehicle for any of the following: trailer towing, heavy loading, taxi, police, delivery service (com- mercial service), off-road, desert operation or more than 50% of your driving is at sustained high speeds during hot weather, above 90°F (32°C).
Page 540 538 MAINTENANCE SCHEDULES WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 541 IF YOU NEED CONSUMER ASSISTANCE CONTENTS SUGGESTIONS FOR OBTAINING SERVICE FOR ▫ Customer Assistance For The Hearing Or Speech YOUR VEHICLE ..... . .541 Impaired (TDD/TTY).
Page 542 540 IF YOU NEED CONSUMER ASSISTANCE DEPARTMENT OF TRANSPORTATION UNIFORM ▫ Traction Grades ..... . .547 TIRE QUALITY GRADES ....547 ▫...
Page 543: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 541 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 544: Fca Us Llc Customer Center
542 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and • Authorized dealer name the latest information to ensure the vehicle is fixed • Vehicle Identification Number (VIN) correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to an authorized FCA US LLC Customer Center dealer service manager first.
Page 545: In Mexico Contact
IF YOU NEED CONSUMER ASSISTANCE 543 Canadian residents with hearing difficulties that require In Mexico Contact assistance can use the special needs relay service offered Av. Prolongacion Paseo de la Reforma, 1240 by Bell Canada. For TTY teletypewriter users, dial 711 Sante Fe C.P.
Page 546: Warranty Information
544 IF YOU NEED CONSUMER ASSISTANCE The manufacturer will not stand behind any service WARNING! contract that is not the manufacturer’s service contract. It is not responsible for any service contract other than the Engine exhaust (internal combustion engines only), manufacturer’s service contract.
Page 547: Mopar® Parts
IF YOU NEED CONSUMER ASSISTANCE 545 campaign. However, NHTSA cannot become involved in MOPAR® PARTS individual problems between you, your authorized MOPAR® fluids, lubricants, parts, and accessories are dealer, and the manufacturer. available from an authorized dealer. They are recom- mended for your vehicle in order to help keep the vehicle To contact NHTSA, you may either call the Auto Safety operating at its best.
Page 548: Publication Order Forms
546 IF YOU NEED CONSUMER ASSISTANCE Diagnostic Procedure Manuals PUBLICATION ORDER FORMS To order the following manuals, you may use either the Diagnostic Procedure Manuals are filled with diagrams, website or the phone numbers listed below. Visa, Mas- charts and detailed illustrations. These practical manuals tercard, American Express, and Discover orders are ac- make it easy for students and technicians to find and fix cepted.
Page 549 IF YOU NEED CONSUMER ASSISTANCE 547 Call toll free at: Treadwear The Treadwear grade is a comparative rating, based on • 1-800-890-4038 (U.S.) the wear rate of the tire when tested under controlled • 1-800-387-1143 (Canada) conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded Visit us on the Worldwide Web at:...
Page 550 548 IF YOU NEED CONSUMER ASSISTANCE Vehicle Safety Standard No. 109. Grades B and A repre- WARNING! sent higher levels of performance on the laboratory test wheel, than the minimum required by law. The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not WARNING! include acceleration, cornering, hydroplaning, or...
Page 551 INDEX I n f o r ma t i o n P r o v i d e d b y :...
Page 552 550 INDEX ABS (Anti-Lock Brake System) ....361 Air Bag Light ......73 Adding Engine Coolant (Antifreeze) .
Page 553 INDEX 551 Anti-Lock Warning Light ....218 Keyless Transmitter Replacement (RKE) ..25 Appearance Care ......509 Belts, Seat.
Page 554 552 INDEX Capacities, Fluid ......526 Changing A Flat Tire ..... . .440 Caps, Filler Chart, Tire Sizing .
Page 555 INDEX 553 Clean Air Gasoline ......410 Coolant (Antifreeze) ..... . .526 Cleaning Coolant Pressure Cap (Radiator Cap) .
Page 556 554 INDEX Defroster, Rear Window.....209 Driving ....... .346 Defroster, Windshield .
Page 557 INDEX 555 Air Cleaner ......486 Exhaust System......101 Block Heater .
Page 558 556 INDEX Power Steering ......356 Materials Added ......411 Fluids, Lubricants And Genuine Parts .
Page 559 INDEX 557 Gear Select Lever Override ....468 Heater, Engine Block ..... . .324 General Information .
Page 560 558 INDEX Integrated Power Module (Fuses) ....517 Lane Change And Turn Signals ....525 Interior Appearance Care .
Page 561 INDEX 559 Cargo .......203 Seat Belt Reminder ..... .218 Center Mounted Stop .
Page 562 560 INDEX Lumbar Support ......157 Automatic Dimming .....110 Electric Powered .
Page 563 INDEX 561 Oil Change Indicator ..... . .237 Overheating, Engine ..... . .437 Oil Change Indicator, Reset .
Page 564 562 INDEX Windows ......35 Rear Window Features .....208 Power Steering Fluid .
Page 565 INDEX 563 Restraints, Child ......77 Engage The Automatic Locking Mode ..56 Retractable Cargo Area Cover .
Page 566 564 INDEX Untwisting Procedure .....52 Settings, Personal ......240 Seats .
Page 567 INDEX 565 Starting Procedures ......321 Tilt Steering Column ..... . .176 Steering Tire And Loading Information Placard .
Page 568 566 INDEX Replacement ......397 Towing Vehicle Behind A Motorhome ...433 Rotation .
Page 569 INDEX 567 Tread Wear Indicators ..... .395 Uconnect® 130 With Satellite Radio Trip Computer ......232 Multimedia Satellite Radio .
Page 570 568 INDEX Vehicle Security Alarm (Security Alarm) ..18 Wheel And Wheel Trim .....512 Vehicle Storage .
Page 571 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 572 FCA US LLC 15MK74-126-AD Fourth Edition Printed in U.S.A. I n f o r ma t i o n P r o v i d e d b y :...

Jeep Patriot 2015 Owner's Manual

Introduction

! Introduction

! Rollover Warning

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Instrument Panel Features

Instrument Cluster

Instrument Cluster Descriptions

Mini-Trip Computer - if Equipped

Electronic Vehicle Information Center (Evic) - if Equipped

UNDERSTANDING YOUR INSTRUMENT PANEL ▫ Operating Instructions - Radio Mode

Uconnect® 230 - AM/FM STEREO RADIO and 6-DISC CD/DVD CHANGER

Jack)

Uconnect® 130

Uconnect® 130 with SATELLITE RADIO

Ipod®/Usb/Mp3 CONTROL - if EQUIPPED

Steering Wheel Audio Controls

CD/DVD Disc Maintenance

Radio Operation and Mobile Phones

Climate Controls

Starting and Operating

Quick Links

Chapters

Related Manuals for Jeep Patriot 2015

Summary of Contents for Jeep Patriot 2015