Table of Contents
Advertisement
AUTO FIND
If none of the codes in the code table operate your equip-
ment, use Auto Find to search for the proper code.
1. Turn on the product you want to operate.
2. Press and hold PRG using a blunt pointed object.
Release PRG after the indicator ligth turns on.
3. Press any key to be programmed
4. Enter "000", then press ENTER within two seconds.
Auto Find is active after the indicator light flashes
and remains lit.
5. Point the remote at the product.
6. Press and release POWER repeatedly, about once a
second, until your products turns off. The indicator
light turns off when you press POWER and on when
you release it.
7. Press ENTER immediately to save the code. The
indicator light flashes to indicate the code has been
saved.
8. Press POWER to turn On your product.
9. Test your product. If the remote fails to operate
some of the basic functions, use Auto Find again to
search for a better code. (Auto Find resumes its
search after the last code that was entered and
saved in step 7).
NOTE: If the indicator light stays on as you press POWER,
Auto Find has tried all of the codes. If the product
you want to control has not turned off, your
remote will not work with that product. To cancel
Auto Find, press PRG at any time during Auto
Find.
CABLE BOX
This remote can control the cable/converter box volume
and muting (instead of the TV's) is available on your
equipment.
1. Program the cable/coverter box normally.
2. After programming the cable/converter box. Press
and hold PRG again using a blunt pointed object.
Release PRG after the indicator light turns on.
3. Press and release the device button the cable box is
assigned to.
4.This time, enter the special code 3-9-9 instead of
the product code.
5. Press and release ENTER to save.
FA - REMOTES
REMOTE PROGRAMMING
(CAT, VCR, AUX, or TV).
1-4
VOLUME OVERRIDE
These remotes can override TV, VCR, or Video Disk
Player volume functions with an amplifier's volume and
muting.
1. Program the amplifier normally.
2. After programming the amplifier, Press and hold PRG
again using a blunt pointed object. Release PRG
after the indicator light turns on.
3. Press and release the device button whose volume
control is to be replaced by the amplifier volume
control. For example, pressing TV will operate the
amplifier's volume while the remote is in TV mode.
4. This time, enter the special code 4-9-9 instead of
the product code.
5. Press and release ENTER to save.
AUXILIARY CAPABILITY
This remote can control up to seven devices. If the
remote has been programmed for four components
using the TV, VCR, CABLE, and AUX keys, you may also
program it for up to three additional using AUX+1,
AUX+2 and AUX+3
To Program AUX+1, AUX+2 AND AUX+3
1. Locate three digit code for product in code table.
2. Press and hold PRG until indicator lights up
3. Press the AUX and 1 simultaneously to select
AUX+1.
4. Enter the three-digit code and press ENTER. The
indicator light should flash and then turn off to
indicate the code has been accepted. If the light
stays on, repeat steps 3 and 4 or try a different
code.
5. Repeat steps 2-4 for AUX+2 and AUX+3.
6. Write the codes on the labels inside battery
compartment for future reference. Hold down AUX
and press 1,2 or 3 to access AUX+1, +2 or +3
mode.
UNIVERSAL ERASER 911
To restore the transmitter back to its initial default
settings, enter the Programming Mode as usual (by
holding PRG until the LED indicator lights), and press 9
1 1, followed by ENTER. The LED indicator will flash
three times to indicate that the transmitter has
returned to its initial default brand codes. Universal
Erase will work in any mode.
Advertisement
Table of Contents
