Page 1
220 - 230 V AC, 50 Hz For the power back-up function: 9 V DC, one 6F22 battery Battery life Approx. 20 hours (for clock backup), using Sony S-006P (6F22) battery Dimensions Approx. 215 × 106.4 × 99.8 mm (w/h/d) ×...
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ICF-C411 SECTION 1 SERVICING NOTES 1-1. CORD DRESSING (POWER CORD) 1) Set the power cord as shown in the figure. power cord 1-2. POINTER ALIGNMENT Align is the projection. 7 screws (P 3x10) pointer gear (VC) 6 MAIN board 4 gear (VC)
ICF-C411 SECTION 3 DISASSEMBLY • The equipment can be removed using the following procedure. Cabinet (Upper) Section Main Board Key Board, LED Board Note : Follow the disassembly procedure in the numerical order given. 3-1. CABINET (UPPER) SECTION 5 cabinet (upper) section...
ICF-C411 SECTION 4 ELECTRICAL ADJUSTMENTS FM SECTION 0 dB = 1 µV FM FREQUENCY COVERAGE ADJUSTMENT Setting: Adjust for a maximum reading on level meter. BAND switch: FM VOLUME control: MIN 86.5 MHz 109.5 MHz FM RF signal FM lead wire...
Page 8
ICF-C411 Adjustment Location: – MAIN board (component side) – ADJUSTMENT LEAD WIRE ANTENNA (SPEAKER) CT2, L2 TUNING CT3, L3 TRACKING FREQUENCY ADJUSTMENT COVERAGE ADJUSTMENT CT1, L1 TRACKING ADJUSTMENT BAND CT4, L4 FREQUENCY COVERAGE ADJUSTMENT...
ICF-C411 SECTION 5 DIAGRAMS 5-1. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. Common Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics KEY board and tantalums.
ICF-C411 5-2. BLOCK DIAGRAM MAIN BOARD VREG w VOLUME BAND 10.7MHz LEAD WIRE ANTENNA DISCRI BAND SW DISCRIMINATOR FM ANT CV1-2 FM RF MIX OUT IF IN DET OUT AF IN AF OUT CT2,L2 FM IF AF POWER (SPEAKER) TRACKING...
ICF-C411 5-3. PRINTED WIRING BOARDS — MAIN, POWER SECTION — • Refer to page 9 for Common Note on Printed Wiring Boards and for Circuit Boards Location. • Semiconductor Location Ref. No. Location D302 D-11 D303 D-11 D305 POWER BOARD...
ICF-C411 SECTION 6 EXPLODED VIEWS • IC Block Diagrams NOTE: • Color Indication of Appearance Parts The components identified by • The mechanical parts with no reference mark 0 or dotted line with mark Example : number in the exploded views are not supplied.
ICF-C411 6-3. CABINET (LOWER) SECTION T301 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark...
ICF-C411 SECTION 7 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark the parts list may be different from the they are seldom required for routine service.
Page 18
ICF-C411 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S104 1-692-014-11 SWITCH, KEYBOARD (TIME SET FAST +) 1-781-861-71 FILTER, CERAMIC (COMBINATION) S105 1-692-014-11 SWITCH, KEYBOARD (TIME SET FAST –) S106 1-692-014-11 SWITCH, KEYBOARD (OFF/ALARM RESET) <...
Page 20
ICF-C411 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...