Reset To The Default Setting (Except For Parental Setting); Information; Troubleshooting Guide - Magnavox MWD200GA Owner's Manual

F

Reset to the Default Setting (Except for PARENTAL Setting)

1
Press [SETUP].
SETUP
STOP
<SETUP MENU>
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU

Troubleshooting Guide

If the unit does not perform properly when operated as instructed in this Owner's Manual, check the unit consulting the following checklist.
Problem
No power
No sound or picture
Distorted picture
Completely distorted picture or
black/white picture with DVD
No sound or distorted sound
No audio at digital output
No DTS audio is output.
Picture freezes momentarily during
playback.
Disc can't be played.
No return to start-up screen when
disc is removed.
The unit does not respond to
the remote control.
Buttons do not work or the unit stops
responding.
The unit does not respond to some
operating commands during playback.
The unit cannot read CDs / DVDs.
Angle does not switch.
Playback does not start
when the title is selected.
The password for rating level
has been forgotten.
NOTES:
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner's
Manual for more details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
• Some functions are prohibited on some discs.
E6C0SUD.indd 17 E6C0SUD.indd 17
2
Select "INITIALIZE".
ENTER
ENTER ENTER ENTER
Press
twice.
INITIALIZE_INITIALIZE
INITIALIZE YES

Information

Solution
– Check if the AC power cord is properly connected.
– Unplug the outlet once, and wait for 5-10 seconds and then plug it in again.
– Check if the TV is switched on.
– Check the video connection.
– Check the VIDEO/AUDIO cable connections to the TV.
(See page 6.)
– Sometimes a small amount of picture distortion may appear.
This is not a malfunction.
– Connect the unit directly to the TV.
– Connect the unit directly to the TV.
– Make sure the disc is compatible with the unit.
– Adjust the volume.
– Check that the speakers are connected correctly.
– Check the digital connections.
– Check if the audio format of the selected audio language matches your receiver capabilities.
– This unit does not support DTS audio.
This is not a malfunction.
– Check the disc for finger prints/scratches and clean with a soft cloth wiping from center to edge.
– Clean the disc.
– Ensure the disc is inserted in correct direction.
– Check if the disc is defective by trying another disc.
– Cancel the parental lock or change the control level.
– Insert a correct disc that plays on this unit.
– Handle a disc with special care so that it does not have fingerprints, scratches, or dusts on its surface.
– Reset the unit by switching the unit off, then on again.
– Aim the remote control directly at the sensor on the front of the unit.
– Reduce the distance to the unit.
– Replace the batteries in the remote control.
– Re-insert the batteries with their polarities (+/– signs) as indicated.
– Tune your radio to an empty AM station so that you hear a lot of noises. Then, turn the volume
up. If you hear some signal sound from the radio by pressing buttons on the remote control, the
remote control is working.
– Press and hold any button on remote control toward a digital camera. The remote control is
working if you confirm infrared light through the digital camera.
– To completely reset the unit, unplug the AC cord from the AC outlet for 5-10 seconds.
– Operations may not be permitted by the disc. Refer to the instructions of the disc.
– Use a commonly available cleaning CD / DVD to clean the lens before sending the unit for
repair.
– The angle cannot be switched for DVDs which do not contain multiple angles. In some cases
multiple angles are only recorded for specific scenes.
– Check the "PARENTAL" setting.
– Enter the default password "4737", then your forgotten password will be cleared.
– 17 –
3
Hint
Select the desired
PLAYER MENU
• When you cancel to
Language, using the
number buttons.
SELECT MENU LANGUAGE
1 ENGLISH
2 FRENCH
3 SPANISH
initialize at step 2.
Press [SETUP] to
exit the menu.
EN
2006/07/06 12:05:46 2006/07/06 12:05:46