IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. The laser beam is emitted from the location shown in the figure. When checking the laser diode, be sure to keep your eyes at least 30 cm away from the pickup lens when the diode is turned on.
IMPORTANT SAFETY PRECAUTIONS Product Safety Notice Also check areas surrounding repaired locations. J. Be careful that foreign objects (screws, solder Some electrical and mechanical parts have special droplets, etc.) do not remain inside the set. safety-related characteristics which are often not K.
Page 6
Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards. 1.
STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is When soldering, be sure to use the Pb free solder. indicated as shown. How to Remove / Install Flat Pack-IC Top View Bottom View 1.
Page 8
3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
Page 9
2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
Page 10
Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart About tightening screws When tightening screws, tighten them with the This flowchart indicates the disassembly steps to gain following torque. access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and Screws Torque dress the cables as they were originally.
Page 12
(S-3B) (S-3A) CN201 CN601 CN301 CN401 [4] DVD Main (L-1) CBA Unit (L-1) (L-2) [2] Front Assembly Fig. D2 Short the three short lands by soldering. (Either of two places.) (S-2) (S-2) [3] Reinforce Plate View for A Connector Fig. D4 Fig.
Page 13
[6] AV CBA (S-4) [5] DVD Mecha (S-4) (S-5) (S-4) (L-3) (S-6) (L-3) Fig. D5 Fig. D6 3. How to Eject Manually 1. Turn the unit over. 2. Insert the shaft less than a diameter of 3 mm (e.g. screwdriver) straightly into the opening as shown. 3.
HOW TO INITIALIZE THE DVD PLAYER To put the program back at the factory-default, initialize the DVD player as the following procedure. 1. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. a appears on the screen. "...
FIRMWARE RENEWAL MODE 1. Turn the power on and remove the disc on the tray. the checksum in (*2) of Fig. e. 2. To put the DVD player into version up mode, press " ******* " differ depending on the models. [9], [8], [7], [6], and [SEARCH MODE] buttons on the remote control unit in that order.
SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 21
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED.
Page 22
DVD Main 1/3 Schematic Diagram 1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT. DVD MAIN 1/3 Ref No. Position IC201 IC202 IC301 IC461 IC462 TRANSISTORS Q251 Q252 Q253 Q254 CONNECTORS CN201 CN301 CN401 E6161SCD1 1-9-3...
Page 23
DVD Main 2/3 Schematic Diagram E6161SCD2 1-9-4...
Page 24
IC101 Voltage Chart ~ : Voltage is not consistent ----- : Not used Unit : Volts PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP PIN.NO PLAY STOP ----- ----- -----...
Page 25
DVD Main 3/3 Schematic Diagram DVD MAIN 3/3 Ref No. Position IC103 IC501 IC502 IC601 CONNECTOR CN601 E6161SCD3 1-9-6...
Page 26
AV 1/2 Schematic Diagram CAUTION ! CAUTION ! For continued protection against fire hazard, Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. replace only with the same type fuse. NOTE: If Main Fuse(F1001)is blown , check to see that all components in the power supply ATTENTION : Pour une protection continue les risqes The voltage for parts in hot circuit is measured using circuit are not defective before you connect the AC plug to the AC power supply.
Page 27
AV 2/2 Schematic Diagram AV 2/2 Ref No. Position IC1201 IC1403 TRANSISTORS Q1201 Q1202 Q1204 Q1351 Q1352 CONNECTOR CN1601 E6161SCAV2 1-9-8...
Page 28
AV CBA Top View CAUTION ! CAUTION ! For continued protection against fire hazard, NOTE: Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. replace only with the same type fuse. The voltage for parts in hot circuit is measured using If Main Fuse(F1001)is blown , check to see that all components in the power supply ATTENTION : Pour une protection continue les risqes hot GND as a common terminal.
Page 29
AV CBA Bottom View CAUTION ! CAUTION ! For continued protection against fire hazard, NOTE: Fixed voltage ( or Auto voltage selectable ) power supply circuit is used in this unit. replace only with the same type fuse. The voltage for parts in hot circuit is measured using If Main Fuse(F1001)is blown , check to see that all components in the power supply ATTENTION : Pour une protection continue les risqes hot GND as a common terminal.
SYSTEM CONTROL TIMING CHARTS Tray Close ~ Play / Play ~ Tray Open Tray Disc Disc Tray Play Close Rotation Stop Open 3.3V Tray IN (TL221) Sled Drive 1.65V (TP303) 1.65V Disc Drive (TP301) 1.65V Focus Drive (TP304) 1.65V Tracking Drive (TP302) 1-12-1 E6NTI...
LEAD IDENTIFICATIONS KTA1267(Y) KTA1266(Y) 2SK3498 KTC3199(GR,Y) KTC3203(Y) G D S E C B E C B KIA4558P MM1636XWRE KIA431-AT K A R LTV-817B-F LD1117SC-R Note: A: Anode K: Cathode 1 2 3 E: Emitter C: Collector B: Base R: Reference G: Gate D: Drain S: Source...
EXPLODED VIEWS Cabinet 2L011 2L011 2L081 2L081 AC1001 2L021 DVD MAIN CBA UNIT 2L021 F1001 2L021 2L105 JK1402 JK1401 JK1201 JK1202 2L031 AV CBA See Electrical Parts List for parts with this mark. 2L041 Some Ref. Numbers are 2L041 not in sequence. 1-14-1 E6161CEX...
MECHANICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C1240 CERAMIC CAP .(AX) B K 1000pF/50V CCA1JKT0B102 Before replacing any of these components, read C1245 CHIP CERAMIC CAP .(1608) F Z 0.1µF/ 50V CHD1JZ30F104 carefully the product safety notice in this service C1246...