Electrical Adjustments; Basic Adjustments - Toshiba MD9DL1 Service Manual

1. BEFORE MAKING ELECTRICAL
ADJUSTMENTS
Read and perform these adjustments when repairing the
circuits or replacing electrical parts or PCB assemblies.
CAUTION
• Use an isolation transformer when performing any
service on this chassis.
• Before removing the anode cap, discharge electricity
because it contains high voltage.
• When removing a PCB or related component, after
unfastening or changing a wire, be sure to put the wire
back in its original position.
Inferior silicon grease can damage IC's and transistors.
• When replacing IC's and transistors, use only specified
silicon grease.
Remove all old silicon before applying new silicon.
Prepare the following measurement tools for electrical
adjustments.
1. Oscilloscope
2. Digital Voltmeter
3. AC Voltmeter
4. Pattern Generator
On-Screen Display Adjustment
1. In the condition of NO indication on the screen.
Press the VOL. DOWN button on the set and the
Channel button (9) on the remote control for more than
1 second to appear the adjustment mode on the screen
as shown in Fig. 1-1.
Function
01 RCUT
Step No.
2. Use the Channel UP/DOWN button or Channel button
(1-0) on the remote control to select the options shown
in Fig. 1-2.
3. Press the MENU button on the remote control to end
the adjustments.

ELECTRICAL ADJUSTMENTS

3E
NO.
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

2. BASIC ADJUSTMENTS

2-1: CONSTANT VOLTAGE
1. Input DC12V to DC Jack and turn the Power ON.
2. Connect the digital voltmeter to the TP401.
3. Set condition is AV MODE without signal.
Adjust the VR501 until the digital voltmeter is 101 ± 0.5V.
4.
5. Input AC100V to AC cord and remove the DC Jack cord.
Check if the Power is ON before doing the above
procedure.
Adjust the VR502 until the digital voltmeter is 102 ± 0.5V.
6.
2-2: RF AGC
Fig. 1-1
1. Receive the VHF HIGH (63dB).
2. Place the set with Aging Test for more than 15 minutes.
3. Connect the digital voltmeter between the pin 5 of
CP101 and the pin 1 of CP101.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (29) on the remote control to
select "AGC".
5. Press the RIGHT/LEFT button on the remote control
until the digital voltmeter is 2.6 ± 0.05V.
2-3: CUT OFF
1. Place the set with Aging Test for more than 15 minutes.
2. Set condition is AV MODE without signal.
3. Using the remote control, set the brightness and contrast
to normal position.
4. Activate the adjustment mode display of Fig. 1-1 and
press the channel button (72) on the remote control to
select "CUT OFF".
5. Adjust the Screen Volume until a dim raster is obtained.
FUNCTION NO
.
R CUT OFF 37
G CUT OFF 38
B CUT OFF 39
G DRIVE 40
B DRIVE 41
BRIGHTNESS(CENT.) 42
BRIGHTNESS(MAX) 43
BRIGHTNESS(MIN) 44
COLOR(CENT.) 45
COLOR(MAX) 46
COLOR(MIN) 47
TINT 48
SUB CONTRAST 49
CONTRAST(CENT.) 50
CONTRAST(MAX) 51
CONTRAST(MIN) 52
SHARPNESS 53
RGB CONTRAST 54
H POSITION 55
V POSITION 56
V SIZE 57
V LINEARITY 58
V S CORRECTION 59
EW PARABOLA CORR. 60
EW TRAPEZIUM CORR. 61
H SIZE 62
V EHT 63
H EHT 64
RF AGC 65
V CENTERING 66
CORNER CORR. TOP 67
CORNER CORR. BTM 68
OSD H 69
FM LEVEL 70
TEST PWM 71
TEST TONE CONTROL 72
FUNCTION
BRI. AV(CENT.)
BRI. AV(MAX)
BRI. AV(MIN)
COL. AV(CENT.)
COL. AV(MAX)
COL. AV(MIN)
TINT AV
SUB CONTRAST AV
CONT. AV(CENT.)
CONT. AV(MAX)
CONT. AV(MIN)
SHARPNESS AV
BRI. DVD(CENT.)
BRI. DVD(MAX)
BRI. DVD(MIN)
COL. DVD(CENT.)
COL. DVD(MAX)
COL. DVD(MIN)
TINT DVD
SUB CONTRAST DVD
CONT. DVD(CENT.)
CONT. DVD(MAX)
CONT. DVD(MIN)
SHARPNESS DVD
BRI. GAME(CENT.)
BRI. GAME(MAX)
BRI. GAME(MIN)
CONT. GAME(CENT.)
CONT. GAME(MAX)
CONT. GAME(MIN)
TUNING V MUTE
POWER ON V MUTE
INPUT LEVEL
SEPARATION L
SEPARATION H
CUT OFF
Fig. 1-2