Kenwood KDC-MP628 Service Manual page 15

● Audio adjust mode
Model with no DSP
• By pressing [AUD] key for less than 1 second, the audio
adjustment mode can be entered.
• Using the remote controller [∗] key and [AUD] key, the au-
dio adjustment mode can be entered.
• Adjustment items of both the AUDIO FUNCTION MODE
and SETUP MODE are included.
• The initial item will be Fader, which is followed by : Balance
→ Bass Level → Middle Level → Treble Level → (Sub Woofer
Level) → HPF Front → HPF Rear → LPF Sub Woofer (Af-
ter this, it will be arbitrary)
• With the remote controller, continuous forwarding is pro-
hibited.
• Using the VOL knob, the Fader can be adjusted in 3 steps :
R15 ↔ 0 ↔ F15 (The initial value is 0)
• Using the VOL knob, the Balance can be adjusted in 3 steps
: L15 ↔ 0 ↔ R15 (The initial value is 0)
• Using the VOL knob, the Bass / Middle / Treble Level can
be adjusted in 3 steps : –8 ↔ 0 ↔ +8 (The initial value is 0)
• Using the VOL knob, the Sub Woofer Level can be adjusted
in 3 steps : –15 ↔ 0 ↔ +15 (The initial value is 0)
• Using the VOL knob, the Volume Offset can be adjusted in
2 steps : –8 ↔ 0 (The initial value is 0)
• Using the VOL knob, the HPF Front / Rear can be adjusted
in 2 steps : Through ↔ 180Hz (or 220Hz) (The initial value
is Through)
• Using the VOL knob, the LPF Sub Woofer can be adjusted
in 2 steps : 60Hz (or 50Hz) ↔ Through (The initial value is
Through)
• Using the VOL knob, the Sub Woofer Phase can be ad-
justed in 2 steps : Reverse ↔ Normal (The initial value is
Normal)
• Using the VOL knob, the Volume Offset can be adjusted in
2 steps : –8 ↔ 0 (The initial value is 0)
• Using the VOL knob, the Loudness ON/OFF can be ad-
justed in 2 steps : OFF ↔ ON (The initial value is OFF)
• 2-Zone ON/OFF can be adjusted in 2 steps : OFF ↔ ON
(The initial value is OFF)
• Bass f / Bass Q / Bass EXT / Middle f / Middle Q / Treble f
do no appear in audio adjustments.
TEST MODE
● MENU items
• Push the [
MENU.
• The [DNPP/SBF] and [DIRECT] keys on the remote con-
troller can also be used to enter the MENU.
• With the remote controller, continuous forwarding is pro-
hibited.
• When a CD is used as a source, the default item will be the
ACD F/W Version.
● 2-ZONE (Dual Zone) items
• When using sources other than the STANDBY source, us-
ing a short-press on [AUTO] or [TI] key, 2-ZONE ON/OFF
is achieved.
● Backup current measurement
When reset in Acc OFF (Back Up ON) condition, MUTE termi-
nal goes off after 2 seconds, instead of 15 seconds. (During
this time, the CD mechanism does not function.)
● OPEL communication items
During the test mode, OPEL communication line outputs the
following (At every 500msec, the output condition of the com-
munication line will be switched.)
CE
DATA
CLK
500msec
500msec
● G sensor display items
When source is STANDBY, by short-pressing [ATT] key, the
display is switched to analogy meter display, in which vertical
G and horizontal G are displayed.
KDC-MP628/MP7028/MP728
MP8029/W7031/W7031Y
] (NEXT) key for at least 1 second to enter the
500msec
15