Blower Installation; Night Light Tm Replacement - Napoleon Castlemore GDS26N Installation And Operation Instructions Manual

ELECTRICAL INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be connected and grounded in
accordance with local codes. In the absence of local codes, use the current CSA C22.1
or the current ANSI/NFPA 70
!
This unit is equipped with a three prong grounding plug for your
protection against shock hazard and should be plugged directly into
a properly grounded three prong receptacle. Do not cut or remove
the grounding prong from this plug.
3. Ensure the thermodisc is touching the wall of the fi rebox. Secure the thermal disk assembly to the rear panel using
4 of # 8 screws supplied. Figure 37b
4. Connect the variable speed switch to the jumper wire (installed in the stove) located just inside the larger knock out
area. Figure 37b
5. Insert the blower assembly into the rear panel and secure using the
remaining #8 screws supplied.
VARIABLE SPEED SWITCH
JUMPER WIRE
VARIABLE
SPEED
SWITCH
KNOB
RED
BLOWER
BULB REPLACEMENT
The GDS26 comes equipped with our "Night Light™".
If in the event the lamp or lens needs to be replaced, follow
these instructions.
1. Turn off all electrical supply.
2. Remove the front and door from the fi rebox.
3. Unscrew the lens cover making sure the washer stays
in place.
Note: Do not handle the lamp (bulb) with bare fi ngers,
protect with a clean dry cloth.
4. The lamp will pull straight out of the socket. Replace with
Wolf Steel Ltd. parts only (W387-0006), as lamp and
l e n s a r e s p e c i a l " h i g h t e m p e r a t u r e " p r o d u c t s .
5. Replace lens with gasket, lense covers, attach wires to
quick connects and replace the door when fi nished.
THE FIREBOX MUST BE SEALED.
FIGURE 38
NorthlineExpress.com

BLOWER INSTALLATION

NATIONAL ELECTRICAL CODE
WARNING
GS67 WIRING DIAGRAM
LOCATED
IN WIRE
HOUSING
(installed in stove)
WHITE
BLACK
WHITE
WIRE
HARNESS
(included in GS67 kit)
GREEN
TO
(GROUND)
POWER
SUPPLY
NIGHT LIGHT
When re-assembling the
light assembly, care must
be taken. "Light Leakage"
from above the cast doors
may be noticed. The holes
in the lamp housing are
necessary for ventilation
and must not be covered.
http://www.northlineexpress.com
in the United States.
1. Break out the blower and thermal
disk knock-outs from the rear panel.
Figure 37a
2. Fish the wire extension through
the blower knock-out as shown
and connect to the prongs on the
thermodisc. Figure 37b
6. R e m o v e t h e
switch housing,
THERMAL DISK
c o n n e c t t h e
v a r i a b l e s p e e d
switch to the jumper
wire and mount the
WIRE
switch to the side
EXTENSION
of the housing.
Attach and secure
the variable speed
switch using the nut
provided. Reinstall
the switch housing.
Install the variable
s p e e d s w i t c h
knob.
FIGURE 36
REPLACEMENT
™
LENS ASSEMBLY INSTALLATION
1. Remove the door from
the fi rebox.
2. Run the wires up through
the lens hole.
3. Align key hole with lens
assembly.
4. Snap into place.
5. Replace light shields,
attach the wires and replace the door to the fi rebox.
LENS ASSEMBLY REPLACEMENT
1. Remove the front
door and top shield
f r o m t h e f i r e b o x .
2. Compress the retainer
fi ns in with a screw driver
while pressing fi rmly on the
top of the light assembly.
3. Once all the retainer
fi ns are pushed in the lens
assembly will snap out of
place.
in Canada
CANADIAN ELECTRICAL CODE
FIGURE 37a
FIGURE 37b
KEY HOLE
FIGURE 39
FIGURE 40
W415-0607 / A / 01.18.08
Toll-Free 1-866-667-8454
21