Related Manuals for McIntosh LCR80
Summary of Contents for McIntosh LCR80
- Page 1 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com LCR80 Loudspeaker System Owner’s Manual...
-
Page 2: Safety Instructions
WARNING - TO REDUCE RISK OF NO USER-SERVICEABLE PARTS FIRE OR ELECTRICAL SHOCK, DO INSIDE. REFER SERVICING TO NOT EXPOSE THIS EQUIPMENT TO QUALIFIED PERSONNEL. RAIN OR MOISTURE. To prevent the risk of electric shock, do not remove cover or back. -
Page 3: Table Of Contents
Customer Service General Information Your decision to own this McIntosh LCR80 Loud- If it is determined that your McIntosh product is in 1. For additional connection information, refer to the speaker System ranks you at the very top among need of repair, you can return it to your Dealer. You owner’s manual(s) for any component(s) connected... -
Page 4: Introduction
Order Designed Network utilizes Capacitors and The two Woofers incorporate McIntosh’s Patented Inductors with high current capacity. Refer to figure LD/HP Magnetic Circuit Design. Finite Element ® 1 F. The LCR80 uses low loss (DCR) Inductors in the LD/HP Pat. No 5,151,943... -
Page 5: Performance Features
The Loudspeaker Elements and Crossover Compo- wire and spade lugs. Banana plugs may also be used. nents of the LCR80 are all chosen for use with ampli- fiers up to 300 watts, yet can be driven with a 75 watt amplifier. -
Page 6: Dimensions
Dimensions Dimensions The following dimensions can assist in determining the best location for your LCR80. Location of Bracket Mounting Holes Front View of the LCR80 Rear View of the LCR80 Front View of the LCR80 (without Grille) End View of the... -
Page 7: Unpacking The Loudspeaker And
10. Attach the two rubber bumpers into bottom side 6. Close the top flaps of the shipping carton and of the LCR80 and two onto the bottom side of the place the top and bottom foam pads on top of the Rear Stabilizers. -
Page 8: Installing The Lcr80 On The Wall
Installing the LCR80 on the Wall The supplied On Wall Mounting Brackets allow for 2. If the LCR80 is to be mounted in a horizontal screw location. Also, be sure to orient the bracket different mounting positions of the LCR80 Loud- position proceed to step 3. - Page 9 Installing the LCR80 on the Wall Horizontal Mounting Vertical Mounting Vertical Mounting with with Flush Hardware with Flush Hardware Angled Hardware Figure 10 Figure 12 Figure 14 Figure 8 -1/8” 7.9cm ” 15/16 7.8cm ” -1/8 7.9cm 16” 16” Figure 11 40.6cm...
-
Page 10: Room Acoustics And Loudspeaker Placement
McIntosh Dealer for more information about this new Figure 20 exciting advance in sound reproduction technology. If a McIntosh product with room correction is not part of your system nor professional measurement of Locating Loudspeakers for use in Home Theater... -
Page 12: How To Connect
8 Ohms to figures A and B. of the terminal to the 2. Insert the Loudspeaker hookup LCR80 COM (Negative [-] ) Input Terminal and 8 Opening 1. Prepare Loudspeaker cables by choosing one of the cable into the Input Terminal Ω... -
Page 13: How To Connect
Note: It is important to maintain the correct po- larity at both ends of the Loudspeaker cables. 8. Connect the other end of the Loudspeaker cables coming from the LCR80 COM (Negative [-] ) and Power Amplifier 8 Ω (Positive [+] )Input Terminals to the Negative (-) and Positive (+) 8 Ω... -
Page 14: Specifications
Specifications Specifications General Specifications System Driver Complement Enclosure Finish Two 6 inch Woofers (incorporating LD/HP Available in various real wood veneers with Two 2 inch Titanium Inverted Dome Midranges a high gloss polyester finish One 3/4 inch Titanium Dome Tweeter Grille Finish Impedance Black Knit Cloth... -
Page 15: Packing Instruction
Loudspeaker a shipping carton or any of the interior part(s) are Grille needed, please call or write Customer Service Depart- Protective Poly ment of McIntosh Laboratory. Please see the Part List Cover for the correct part numbers. Protective Fiber Quantity... - Page 16 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 www.mcintoshlabs.com The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A. McIntosh Part No. 04129900...