TV-F2400 SERVICE MANUAL COLOR TELEVISION • This Service Manual is the “Revision Publishing” and replaces “Simple Manual” (S/M Code No. 09-005-431-9T1). • This Service Manual does not include “ADJUSTMENT”. This item will be issued in the next Supplement. S/M Code No. 09-007-431-9R1...
SPECIFICATIONS Tuner System Frequency synthesized tuner TV System NTSC-M Channel Coverage VHF: 2 to 13 UHF: 14 to 69 CATV: 5A, A-1 to A-5, A to W, W+1 to W+84 Program Memory Antenna Input 75 ohms, unbalanced Picture Tube 24 in. Screen Size 478 (W) x 359 (H) mm x 14...
NOTICES BEFORE REPAIRING To make the best use of this equipment, make sure to obey the following items when repairing (or mending). 1. Do not damage or melt the tunicate of the leading Insulation resistance: 1 MΩ (500 V/s) wire on the AC1 side, including the power supply Voltage-withstand: 1 kV for 1 minute cord.
DISASSEMBLY INSTRUCTIONS 1. REAR CABINET REMOVAL Front cabinet (1) Remove four screws 1 , and three screws 2 , then remove the rear cabinet in the direction of the arrow. (See Figure1-1) Rear cabinet Figure 1-1 2. HIGH-VOLTAGE CAP (ANODE CAP) REMOVAL 2-1.
Page 5
(5) Push the anode cap with your thumb in the direction of arrow 1 as shown in the figure, then lift the cap in the direction of arrow 2 to release the hook on one side. (See Figure 2-3) Anode cap Hook Hook Figure 2-3...
Page 6
(3) Eliminate twisting, etc. of the high-voltage cable and High-voltage cable Anode cap arrange it so that no twisting occurs. (See Figure 3-3) Caution : If the cable is not arranged correctly, the anode cap could turn and cause an installation defect. Figure 3-3 (4) Turn over the rubber cap symmetrically on the left and right.
Page 7
(6) Apply the hook on one side to the anode button as shown on the figure. (See Figure 3-6) Caution : Check that the hook is held securely. (7) Apply the hook on the other side to the anode button as Hook shown in Figure 3-7.
Page 8
4. NK C.B REMOVAL (1) Disconnect CN903 (CRT GND). (2) Disconnect CN901, CN902, CN951, CN952. CN882 (3) Remove the NK C.B in the direction of arrow 1 . (Power cord) (See Figure 4-1) CN807 5. MAIN C.B REMOVAL (1) Remove connector (CN404). (2) Remove connector (CN882).
Page 9
ELETRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION MAIN C.B 8A-JE7-621-010 IC,M37272MA-052SP C001 87-010-405-080 CAP,E 10-50 M 11L SME 87-A91-538-010 RCR UNIT,SBX1981-72P C002 87-018-209-080 CAP,TC U 0.1-50 Z F UP050 87-A21-378-010 IC,S-24C04BDP-1A C003 87-018-134-080 CAP,TC U 0.01-16 N Y UP050...
Page 10
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C328 87-010-405-080 CAP,E 10-50 M 11L SME C807 87-A10-568-010 CAP,PP 1000P-630 J APH C329 87-018-134-080 CAP,TC U 0.01-16 N Y UP050 C808 87-010-384-080 CAP,E 100-25 M 11L SME C330 87-010-401-080 CAP,E 1-50 M 11L SME...
Page 11
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION L204 87-003-282-080 COIL,12UH J LAL02 C408 87-010-405-080 CAP,E 10-50 M 11L SME L205 8Z-JBH-610-010 COIL,PIF-SQ57EL349A 45.75MHZ C409 87-010-404-080 CAP,E 4.7-50 M 11L SME L206 87-005-614-080 COIL,100UH J LAV35 C410 87-010-404-080 CAP,E 4.7-50 M 11L SME...
Page 12
REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION C488 87-010-384-080 CAP,E 100-25 M 11L SME C915 87-010-260-080 CAP,E 47-25 M 11L SME C489 87-010-197-080 C-CAP,S 0.01-25 K B C2012 C916 87-018-134-080 CAP,TC U 0.01-16 N Y UP050 C492 87-010-197-080 C-CAP,S 0.01-25 K B C2012...
CHIP RESISTOR PART CODE Chip Resistor Part Coding Figure Resistor Code Value of resistor Chip resistor Dimensions (mm) Wattage Type Tolerance Symbol Resistor Code Form 1/16W 1005 0.35 1/16W 1608 0.45 1/10W 2125 1.25 0.45 1/8W 3216 0.55 TRANSISTOR ILLUSTRATION E C B B C E B C E...
Page 25
IC DESCRIPTION IC, M37272MA-0525SP Pin No. Pin Name Description BLK H Blanking H sync input. BLK V Blanking V sync input. A MUTE Audio Amp mute. L MUTE Audio mute. Q SUR Q surround switch. EEPROM Write protect. V MUTE Video mute BPF switch.