Advertisement
BOX CONTENTS
Unpacking
As listed below, each ScanX System is shipped in a
single carton containing the ScanX main assembly and
associated accessory kit. Unpack each component of
the ScanX and inspect for physical damage such as
scratched panels, damaged connectors, etc.
If any damage is noted, immediately notify your ALLPRO
Imaging authorized dealer immediately so corrective action
can be taken. Save all cartons and packing materials to
protect the ScanX in the event of future transport or shipping.
Included System Components
Each ScanX system consists of the indicated main assembly
and accessory kit as listed. Refer to the TECHNICAL DATA
section of the Operator's Manual included on the Drivers
and Utilities Disk for ratings and identification for specific
ScanX models. Verify that all listed items were received. If
any item is missing, notify your dealer.
Make sure to read and follow the Operator's Manual (P/N D5471) included as a PDF file on the
Drivers and Utilities Disk (P/N D5475) to ensure that your ScanX gives the highest level of service
SETUP & OPERATION
ScanX Drivers and Utilities Installation
Before connecting the ScanX to your computer or attempting to use it for the first time, run the Setup program on the ScanX
Drivers and Utilities Disk (P/N D5475) included with the ScanX. Normally, this program runs automatically when the CD is inserted
into the drive for the first time. If not, run the Setup program located in the root directory of the CD (typically D:\AutoRun.exe).
ScanX Connections
As shown by the illustration at right, connecting
the ScanX for operation consists of the following
Setup program on the ScanX
1. Connect the ScanX to the computer
via supplied USB cable.
2. Connect the ScanX to power source
via supplied line cord.
ScanX Operation
Operate the ScanX connected to a properly set up computer as follows:
1. Place the ScanX rocker switch to the ON (I) position.
2. Press the READY switch to turn ON the ScanX.
3. Verify that the READY indicator illuminates.
4. Activate the scanner via the Imaging Software.
5. Verify that all track status indicators illuminate green.
6. Minimize exposure to ambient light and insert the PSP into the ScanX
inlet with the sensitive (front) side of PSP towards the ScanX.
7. Verify that all track status indicators illuminate yellow.
8. Observe that the scanned PSP exits through the scanner arch.
Quick Start Instructions
Accessory Kit containing:
Brush Kit
Dust Cover
6-Foot USB Cable
10-Foot Power Cord
Size 0 Plate Guides, Pack of 4
Size 1 Plate Guides, Pack of 4
Size 2 Plate Guides, Pack of 4
Size 3 Plate Guides, Pack of 4
Size 4 Plate Guides, Pack of 4
Accessory Literature Kit:
Important
Note:
The Main Power Switch is the
Mains disconnect device.
Corporate:
1295 Walt Whitman Road
Phone: 800-247-8324
West Coast:
291 Bonnie Lane, Suite 101
Phone: 800-247-8324
Website: a llpr oi m agi ng.c o m
System Components - ScanX Quantum, P/N D5000-Q
Sample ScanX Cleaning Sheet Kit
CD Disk containing Drivers, Utilities and
Operator's Manual
Main Power
Switch (1/0)
Eraser
Status
Indicator
|
Melville, New York 11747- 3062
|
Fax: 888-247-8481
|
Corona, CA 92880 - 2804
|
Fax: 951-898-7646
D5471Q
D5492
D5027
D5262
D5226
61035
D5231
D5232
D5233
D5234
D5235
D5492-LIT
B2030
D5475
.
Type B USB Connector
Type A USB
Connector to
IEC Connector
Computer
Line Cord
From
Mains
Outlet
ERASER
Switch
READY
Switch
Scanner
Ready/Standby
Track Status
Status Indicator
Indicators
Advertisement
