1. Manuals
  2. Brands
  3. Invacare Manuals
  4. Wheelchair
  5. Topan
  6. User manual

Invacare Topan User Manual

Powerchair
Hide thumbs Also See for Topan:
Table of Contents

Advertisement

Quick Links

Download this manual
Invacare® Topan
Powerchair
User Manual

Advertisement

Table of Contents
loading

Related Manuals for Invacare Topan

Summary of Contents for Invacare Topan

  • Page 1 Invacare® Topan Powerchair User Manual...
  • Page 2 How can you get in touch with Invacare®? If you have any questions or need support, please contact your authorised Invacare® Dealer, who has the necessary know-how and equipment plus the special knowledge concerning your Invacare® product, and can offer you all-round satisfactory service. Should you wish to contact Invacare® directly, you can reach us in Europe at the following addresses and phone numbers.
  • Page 3 Bridgend Industrial Estate uk@invacare.com Mid Glamorgan - CF31-3PY eire@invacare.com United Kingdom WWW: www.invacare.co.uk Invacare Mecc San s.r.l. +39 - 0445 - 38 00 59 Via Dei Pini, 62 Fax: +39 - 0445 - 38 00 34 I - 36016 Thiene (VI) italia@invacare.com...
  • Page 4 +31 - (0)318 - 69 57 57 Celsiusstraat 46 Fax: +31 - (0)318 - 69 57 58 NL-6716 BZ Ede csede@invacare.com The Netherlands WWW: www.invacare.nl Invacare (Portugal) II +351-225105946 Rua Estrada Velha, 949 Fax: +351-225105739 4465-784 Leça do Balio portugal@invacare.com Portugal WWW: www.invacare.pt...

  • Page 5: Table Of Contents

    Safety Information on Electromagnetic Interference............18 Safety Information on Driving and Freewheel Mode............19 Key features Topan with Standard Seat ......................21 Topan with Laguna Seat ......................22 Getting in and out of the wheelchair Removing the padded armrest in order to side transfer .............23 Removing the ergonomic armrest in order to side transfer ..........24...
  • Page 6 Driving up and down gradients....................29 Pushing the wheelchair in freewheel mode Disengaging Motors ........................30 The Shark II Remote Assembly of the remote......................31 Battery charging display......................33 Adjusting speed........................34 Using the speedometer......................34 “5 Speed” and “VSP” modes ....................35 Status display ..........................36 Activate/de-activate the immobiliser ..................36 Using the remote to control the wheelchair .................37 7.8.1 How a wheelchair with "Indirect Steering"...
  • Page 7 Adjusting the trunk supports ....................53 8.3.1 Adjusting the width......................53 8.3.2 Adjusting the height ......................54 8.3.3 Adjusting the depth .......................55 Adjusting the headrest......................56 Legrests............................57 8.5.1 Modifying the seat depth in the front by adjusting the position of the legrest support brackets ........................57 8.5.2 Standard / Junior / Mini Legrests (firm seat)..............58 8.5.2.1...
  • Page 8 Electrical System Electronics Protection System ....................76 9.1.1 The main fuse .......................77 Batteries ...........................78 9.2.1 What you need to know about batteries ...............78 9.2.2 Charging the batteries ....................80 9.2.3 Removing and fitting batteries ..................82 9.2.3.1 Removing the batteries....................83 9.2.3.2 How to handle damaged batteries correctly ............85 10 Care and maintenance 11 Repair Instructions 11.1...

  • Page 9: Introduction

    The decision whether the model is suitable for the user may only be taken by medical specialists with appropriate expertise. Invacare® or their statutory representatives can accept no liability in cases in which the wheelchair has not been adapted to suit the users’ handicaps.
  • Page 10 This manual contains copyrighted information. This manual may not be reproduced or reprinted either partly or completely without previous written consent from Invacare® or its statutory representatives. We reserve the right to make any necessary alterations on the grounds of...

  • Page 11: Important Symbols In This Manual

    Important symbols in this manual WARNING! This symbol warns you of danger! • Always follow these instructions to avoid injury to the user or damage to the product! EXPLOSION HAZARD! This symbol warns you of an explosion hazard, an example of which can be caused by excessive tyre pressure in a pneumatic tyre! •...

  • Page 12: Important Symbols Found On The Vehicle

    Important symbols found on the vehicle This product has been supplied from an environmentally aware manufacturer that complies with the Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/CE. This product may contain substances that could be harmful to the environment if disposed of in places (landfills) that are not appropriate according to legislation.

  • Page 13: Type Classification And Permissible Use

    Type classification and permissible use This vehicle was designed for persons whose ability to walk is impaired, but who are still physically and mentally able to operate an electric vehicle. It has been classified according to EN 12184 as a class B mobility product (for indoor and outdoor areas).

  • Page 14: Indications

    Indications The use of this mobility product is recommended for the following indications: The inability or a greatly restricted ability to walk within the scope of the basic requirement to be able to move within one’s own four walls. The need to leave the dwelling place in order to get some fresh air during a short walk or to reach those places generally to be found at close distance to the dwelling and where everyday business is carried out.

  • Page 15: Safety Notes

    Safety Notes • READ WELL BEFORE OPERATION! General Safety Notes Danger of injury if mobility device is used in any other way than the purpose described in this manual! • Only ever use the mobility device in accordance with the instructions in this User's Manual (see Chapter "Type classification and permissible use"...
  • Page 16 Danger of injury if the mobility device is switched off while driving, for example by pressing the On/Off Button or disconnecting a cable, due to it coming to an abrupt, sharp stop! • If you have to brake in an emergency, simply release the joystick which will bring you to a halt! (please Refer to the joystick operating manual for more information).
  • Page 17 Danger of fire or breaking down due to electric devices being connected! • Do not connect any electric devices to your mobility device that are not expressly certified by Invacare® for this purpose! Have all electrical installations done by your authorised Invacare® Dealer!

  • Page 18: Safety Information On Electromagnetic Interference

    Safety Information on Electromagnetic Interference This electric vehicle was successfully tested in accordance with International standards as to its compliance with Electromagnetic Interference (EMI) Regulations. However, electromagnetic fields, such as those generated by radio and television transmitters, and cellular phones, can influence the functions of electric vehicles.

  • Page 19: Safety Information On Driving And Freewheel Mode

    Safety Information on Driving and Freewheel Mode Danger of injury if the wheelchair tips over! • Inclines and declines can only be travelled up to the maximum safe slope (please see Chapter "Technical Specifications" from Page 103). • Always return the backrest of your seat or the seat tilt to an upright position before ascending slopes! We recommend that you position the seat backrest and the seat tilt (if fitted) slightly to the rear before descending slopes! •...
  • Page 20 Danger of breaking down in adverse weather conditions, i.e. extreme cold, in an isolated area! • If you are a user with severely limited mobility, we advise that in the case of adverse weather conditions DO NOT attempt a journey without an accompanying attendant! Danger of injury if your foot slides off the footrest and gets caught underneath the wheelchair when it is in motion! •...

  • Page 21: Key Features

    Key features Topan with Standard Seat 1) Push handle 2) Wing screw for adjusting the remote to the length of the arm 3) Hand wheel and fixation screw adjusting the angle of the backrest 4) Declutching lever of the drive motors...

  • Page 22: Topan With Laguna Seat

    Topan with Laguna Seat 1) Clamping lever for adjusting the headrest 2) Push handle 3) Fixation screw for adjusting the width of the trunk supports 4) Fixation screw for adjusting the remote to the length of the arm 5) Fixation screw for adjusting the height...

  • Page 23: Getting In And Out Of The Wheelchair

    Getting in and out of the wheelchair Important information for getting into and out of the wheelchair from the side! The armrest must be removed in order to get into or out of the wheelchair from the side. Removing the padded armrest in order to side transfer •...

  • Page 24: Removing The Ergonomic Armrest In Order To Side Transfer

    Removing the ergonomic armrest in order to side transfer • Disconnect the cable (1) from the remote. • Release the hand knob (2). • Pull the side part out of the holder.
  • Page 25 Getting into the wheelchair: • Position your wheelchair as close as possible to your seat. This might have to be done by an attendant. • Switch your wheelchair off. • Apply the manual wheel lock of your wheelchair (if existing). •...

  • Page 26: Driving

    Driving NOTE The maximum load capacity that is stated in the technical data only states that the system is designed for this mass in total. However, this does not mean that one can sit a person with this body weight in the wheelchair without restrictions. Attention must be paid to the body proportions, such as height, weight distribution, abdominal girth, leg and calf girth and seat depth.

  • Page 27: Parking And Stationary

    • The rear mirror (if fitted) is fitted so that you can always look behind you without having to lean forward or change your seat position in any way. Parking and stationary When parking your vehicle or if your vehicle is stationary for a prolonged period: •...

  • Page 28: Taking Obstacles

    Taking Obstacles Your wheelchair can overcome obstacles and kerbs with the following heights. • 10 cm CAUTION: Danger of Tipping Over! • Never approach obstacles at an angle! • Put your backrest into an upright position before climbing an obstacle! Driving up over an obstacle Correct •...

  • Page 29: Driving Up And Down Gradients

    Driving up and down gradients For information concerning the maximum safe slope, please see chapter "Technical Specifications" starting on page 103. WARNING: Danger of tipping over! • Only ever drive downhill at a maximum of 2/3 of the top speed! Avoid sudden changes of direction or abrupt braking when driving on slopes! •...

  • Page 30: Pushing The Wheelchair In Freewheel Mode

    Pushing the wheelchair in freewheel mode The motors of the wheelchair are equipped with automatic brakes, preventing that the wheelchair starts rolling out of control when the joystick box is switched off. When pushing the wheelchair manually whilst freewheeling, the magnetic brakes must be disengaged. Disengaging Motors Danger of the vehicle running away! •...

  • Page 31: The Shark Ii Remote

    The Shark II Remote Assembly of the remote Top side (standard) Battery charging display ON/OFF button Activate / connect through / deactivate adjusting mode Reduce travel speed Travel speed display Horn Increase travel speed LED for “control unit activated for accompanying person“...
  • Page 32 Top side (including light option) 11) Warning indicator 12) Left hand indicator 13) Light 14) Right hand indicator 15) LED for “light activated“ Lower side 1) Combined charging socket / programming socket...

  • Page 33: Battery Charging Display

    Battery charging display • Battery charging All diodes illuminated: full range! display • Only the yellow and red diodes are illuminated: Reduced range! Charge batteries before a longer trip! • Only the red diodes are illuminated: Very low range! Charge batteries as soon as possible! •...

  • Page 34: Adjusting Speed

    Adjusting speed The user can adjust the chair’s top speed to suit their preferences and environment. The currently selected top speed is shown on the Speedometer and can be adjusted using the “Increase Speed” (2) and “Reduce Speed” (1) buttons. Using the speedometer Each of the speedometer’s 6 large LEDs typically represent 0%, 20%, 40%, 60%, 80% and 100% of the chair’s maximum speed.

  • Page 35: Speed" And "Vsp" Modes

    “5 Speed” and “VSP” modes Shark II supports 2 modes of top speed adjustment – “5 Speed” and “VSP” modes. In the “5 Speed” mode pressing the Increase Speed and Decrease Speed buttons steps between one of the 5 top speeds 20% to 100%. In the “VSP”...

  • Page 36: Status Display

    Status display The status display serves to display error messages. For error codes see chapter "Error Codes and Diagnostic Codes" on page 43. Activate/de-activate the immobiliser Activate the immobiliser Activate • Whilst the remote is switched on, press and hold the ON/OFF button (1) for 4 seconds.

  • Page 37: Using The Remote To Control The Wheelchair

    • Invacare® supplies all electric vehicles from the factory with a standard drive programme. Invacare® can only assume a warranty for the safe vehicle handling of the electric vehicle – in particular tipping stability - for this standard drive programme! Will the wheelchair not drive after switching on? Check the drive-away lock (see chapter "Activate/de-activate the immobiliser "...

  • Page 38: How A Wheelchair With "Indirect Steering" Reacts To Joystick Movements

    7.8.1 How a wheelchair with "Indirect Steering" reacts to joystick movements. "Indirect Steering" occurs by individually applying power to the drive wheels, and is found on wheelchairs with front, rear and middle wheel drive. Travel direction The further the joystick is moved in a particular direction, the more dynamically the wheelchair reacts.

  • Page 39: Operating The Electric Adjustment Options

    7.8.2 Operating the electric adjustment options Electric adjustment options are operated using the joystick. • Press the adjustment mode button once in order to activate the first adjustment option. Press the adjustment mode button twice in order to activate the second adjustment option.

  • Page 40: Control Unit For An Accompanying Person (Option)

    Control unit for an accompanying person (option) The control unit for an accompanying person enables the control of the wheelchair to be handled by an accompanying person. 7.9.1 Layout of the remote Joystick Change over control unit to accompanying person/occupant Activate/connect through/deactive adjustment mode Set travel speed...

  • Page 41: Operating The Electric Adjustment Options

    7.9.2 Operating the electric adjustment options Electric adjustment options are operated by means of the joystick. The control unit must be switched over to ’accompanying person’ for the adjustment options to be operated via the control unit for the accompanying person. •...

  • Page 42: Error Diagnosis

    7.10 Error diagnosis If the electronic system shows a failure, please use the following guide to locate the fault. NOTE: Ensure that the drive electronics system is switched on before starting any diagnosis. If the status display is OFF: Check whether the drive electronics system is SWITCHED ON. Check whether all cables are correctly connected.

  • Page 43: Error Codes And Diagnostic Codes

    7.11 Error Codes and Diagnostic Codes FLASH FAULT EFFECT Comments CODE User error or drive Stops driving • Ensure that the joystick is in the neutral motors overloaded central position (simply release the joystick) and switch on again. • Drive motors overloaded. Shut electronics down and then switch on again.
  • Page 44 FLASH FAULT EFFECT Comments CODE Error in Shark Stops driving • Check remote bus cable and all remote connecting plugs. • Replace remote. Error in Shark Stops driving • Check all cables and connecting plugs in power module the Shark system. •...

  • Page 45: Adjusting The Wheelchair To The User's Seating Posture

    Adjusting the wheelchair to the user's seating posture Adjusting the armrests and the joystick box 8.1.1 Adapting the remote to the length of the user’s arm • Loosen the wing screw (1). • Set the remote to the desired length by pushing forward or backward.

  • Page 46: Adjusting The Height Of The Remote (Option)

    8.1.2 Adjusting the height of the remote (option) Pre-requisites: • 1x 4 mm Allen key • Use the Allen key to loosen the fastening screw (1) of the skirt guard. • Use the Allen key to loosen the fastening screw (2) of the remote fixation. •...

  • Page 47: Adjusting The Height Of The Armrest

    8.1.3 Adjusting the height of the armrest Pre-requisites: • 1x Phillips screwdriver • Disconnect the cable (1) from the remote. • Loosen the wing screw (2). • Pull the side part out of the holder.
  • Page 48 The stop screw (1) of the side part has six different positions. • Loosen and remove the stop screw (1) of the side part, using the Phillips screwdriver. • Position the stop screw to the desired height and re-tighten.

  • Page 49: Adjusting The Width Of The Armrests

    8.1.4 Adjusting the width of the armrests The distance between the side sections can be adjusted by 1.5 cm on both sides (3 cm in total). Where to find the clamping levers? The picture below shows the position of the clamping levers (1) that enable adjustment of the width of the armrests.
  • Page 50 Doing the adjustment • Loosen the clamping lever (1). • Set the armrest to the desired position. • Re-tighten the clamping lever. • Check that the armrest is fastened firmly. • Repeat the procedure for the other armrest.

  • Page 51: Adjusting The Backrest

    Adjusting the backrest 8.2.1 Adjusting the backrest electrically The angle of the electrically adjustable backrest is continuously adjustable between -2° and +30°. The actuator is controlled via the remote. Please see chapter "Operating the electric adjustment options" on page 39.

  • Page 52: Adjusting The Backrest Manually

    8.2.2 Adjusting the backrest manually The angle of the manually adjustable backrest is continuously adjustable between +2° and +22°. Pre-requisites: • 1x Open-end spanner 13 mm • 1x Phillips screwdriver The angle of the manually adjustable backrest is adjusted on both sides by means of a knurled adjustment screw (1) and a limiting screw (2), which is fitted with a counter nut (3).

  • Page 53: Adjusting The Trunk Supports

    Adjusting the trunk supports The trunk supports can be adjusted in three different ways: • Width • Height • Depth 8.3.1 Adjusting the width • Loosen the knurled screws (1). • Set the trunk supports to the desired position. • Re-tighten the knurled screws.

  • Page 54: Adjusting The Height

    8.3.2 Adjusting the height Requirements: • Allen key 5 mm • Loosen the Allen screw of the height adjustment (1). • Set the trunk supports to the desired height. • Re-tighten the screws.

  • Page 55: Adjusting The Depth

    8.3.3 Adjusting the depth Requirements: • Allen key 5 mm • Loosen the screws (1) that allows the support pads to slide forwards and backwards. • Adjust the supports to the desired position. • Re-tighten the screws.

  • Page 56: Adjusting The Headrest

    Adjusting the headrest • Loosen the clamping lever (1,2 or 3). • Adjust the headrest to the required position. • Retighten clamping lever.

  • Page 57: Legrests

    Legrests 8.5.1 Modifying the seat depth in the front by adjusting the position of the legrest support brackets The seat depth in the front can be modified by adjusting the position of the legrest support brackets. Adjusting the position of the legrest support brackets is the same for all types of legrests. Pre-requisites: •...

  • Page 58: Standard / Junior / Mini Legrests (Firm Seat)

    8.5.2 Standard / Junior / Mini Legrests (firm seat) 8.5.2.1 Adjusting the length of the legrest WARNING: Danger of injury and danger of damage to the wheelchair if the legrests do not have sufficient ground clearance! • Always make sure the legrests have sufficient ground clearance when adjusting the length, keeping in mind that the necessary ground clearance is increased when overcoming obstacles! Pre-requisites:...

  • Page 59: Angle Adjustable Legrest

    8.5.3 Angle adjustable legrest 8.5.3.1 Adjusting the angle of the legrest Pre-requisites: • 1x open-ended spanner 13 mm • 1x open-ended spanner 10 mm • 1x Allen key 4 mm • Loosen the fixation screws (1) of the pivotal points of the angel adjustment, using the open-ended spanner 10 mm and the Allen key 4 mm.
  • Page 60 On the underside of the legrest hanger there is a slit (A) in the outer tube, which allows visual inspection. When adjusting the angle, the inner tube (D) should only ever be pulled out so far that its end is flush with the edge (B) of the clamp (C).

  • Page 61: Adjusting The Length Of The Legrest

    8.5.3.2 Adjusting the length of the legrest WARNING: Danger of injury and danger of damage to the wheelchair if the legrests do not have sufficient ground clearance! • Always make sure the legrests have sufficient ground clearance when adjusting the length, keeping in mind that the necessary ground clearance is increased when overcoming obstacles! Pre-requisites:...

  • Page 62: Manually Height Adjustable Legrest

    8.5.4 Manually height adjustable legrest 8.5.4.1 Adjusting the angle of the legrest • To raise the legrest, slowly pull it upwards. • To lower the legrest, press the lever (1) down and adjust the legrest to the desired position.

  • Page 63: Adjusting The Length Of The Legrest

    8.5.4.2 Adjusting the length of the legrest WARNING: Danger of injury and danger of damage to the wheelchair if the legrests do not have sufficient ground clearance! • Always make sure the legrests have sufficient ground clearance when adjusting the length, keeping in mind that the necessary ground clearance is increased when overcoming obstacles! Pre-requisites:...

  • Page 64: Adjusting The Height Of The Swing-Away Calf Plate

    8.5.4.3 Adjusting the height of the swing-away calf plate Pre-requisites: • 1x Open-ended spanner 13 mm The calf support has three height adjustments (1). • Use the open-ended spanner to loosen the nut (2). • Set the calf support to the desired height. •...

  • Page 65: Electrically Height Adjustable Legrest

    8.5.5 Electrically height adjustable legrest 8.5.5.1 Adjusting the angle of the legrest The electrically height adjustable legrests are operated via the remote. Please see chapter "Operating the electric adjustment options" on page 39. 8.5.5.2 Adjusting the length of the legrest WARNING: Danger of injury and danger of damage to the wheelchair if the legrests do not have sufficient ground clearance! •...
  • Page 66 • Loosen the wing screw (1). • Set the legrest to the desired length. • Re-tighten the wing screw.

  • Page 67: Adjusting The Height Of The Swing-Away Calf Plate

    8.5.5.3 Adjusting the height of the swing-away calf plate Pre-requisites: • 1x Phillips screwdriver The height adjustment the calf support is infinitely variable. • Loosen the screws (1) using the Phillips screwdriver. • Set the calf support to the desired height. •...

  • Page 68: Rea Legrest

    8.5.6 REA Legrest 8.5.6.1 Adjusting the angle of the legrest • To adjust the angle of the legrest, pull the lever (1) outward and rotate approximately half a turn counterclockwise to release the clamping screw. • Adjust legrest to the desired angle. •...

  • Page 69: Adjusting The Length Of The Legrest

    8.5.6.2 Adjusting the length of the legrest • Loosen the wing screw (1). • Set the legrest to the desired length. • Re-tighten the wing screw.

  • Page 70: Adjusting The Height Of The Swing-Away Calf Plate

    8.5.6.3 Adjusting the height of the swing-away calf plate The height adjustment the calf support is infinitely variable. • Loosen the clamping screw (1). • Set the calf support at the desired height. • Re-tighten the screw.

  • Page 71: Adjusting The Position Of The Swing-Away Calf Support

    8.5.6.4 Adjusting the position of the swing-away calf support The calf support has three depth adjustments (1). • Loosen and remove the fixation screws (1) of the calf pad..
  • Page 72 • Use the Allen key 5 mm to loosen and remove the lateral fixation screw (1) of the calf support. • Set the calf support to the desired depth. • Re-position and tighten the screw. • Re-position the calf pad and fasten with the screws.

  • Page 73: Adjusting And Removing The Tray

    Adjusting and removing the tray CAUTION: Injury hazard or material damage if an electric wheelchair which is fitted with a table is transported in a vehicle! • If a table is fitted, always remove it before transporting the wheelchair! 8.6.1 Laterally adjusting the tray •...

  • Page 74: Adjusting The Depth Of The Tray / Removing The Tray

    8.6.2 Adjusting the depth of the tray / removing the tray • Loosen the wing-screw (1). • Adjust the table to the desired depth (or remove it entirely). • Re-tighten the screw. 8.6.3 Swinging the tray away to the side CAUTION! Risk of injury! When the tray is raised it does not lock in place in this position! •...

  • Page 76: Electrical System

    Electrical System Electronics Protection System The vehicle's electronics are equipped with an overload-protection system. If the motors are put under considerable strain for a longer period of time (for example, when driving up a steep hill) and especially when the ambient temperature is high, then the electronic system could overheat.

  • Page 77: The Main Fuse

    NOTE A defective main fuse may be replaced only after checking the entire electric system. An Invacare® specialised dealer must perform the replacement. You can find information on the fuse type in chapter "Technical Specifications" starting on page 103. The entire electric system of the wheelchair is protected by the main fuse against overloading.

  • Page 78: Batteries

    Batteries 9.2.1 What you need to know about batteries Power is supplied by two 12V batteries. The batteries are maintenance-free and only need regular charging. New batteries should always be fully charged once before their first use. New batteries will be at their full capacity after having run through approx.
  • Page 79 The batteries cannot be overcharged with the specified charger. Please use only charging devices in Class 2. This class of chargers may be left unattended during charging. All charging devices which are supplied by Invacare® comply with these requirements.

  • Page 80: Charging The Batteries

    • Only ever use the battery charger supplied with your vehicle, or a charger that has been approved by Invacare®! Danger of electric shock and damage to the battery charger if it is allowed to get wet! • Protect the battery charger from water! •...
  • Page 81 Charging the batteries • Switch off the electric wheelchair on the remote. • Connect the charging device to the remote. The charging socket is to be found on the underside of the remote (1). • Connect the charging device to the power supply and switch on if necessary.

  • Page 82: Removing And Fitting Batteries

    9.2.3 Removing and fitting batteries WARNING: Danger of injury if the batteries are not handled correctly during assembly and maintenance work! • New batteries should be installed by authorised technicians! • Observe the warnings on the batteries! • Take into account the heavy weight of the batteries! •...

  • Page 83: Removing The Batteries

    9.2.3.1 Removing the batteries CAUTION: Risk of fire and burns if battery poles are bridged! • When replacing the batteries the battery poles MUST NOT come into contact with metal parts of the wheelchair causing bridging. • Be sure to replace the battery pole caps after the batteries have been replaced. Pre-requisites: •...
  • Page 84 • Pull the battery pole caps (1) upward and push back in order to reach the battery poles. • Use the open-ended spanner to loosen the battery pole clamps. • Remove the batteries to the rear.

  • Page 85: How To Handle Damaged Batteries Correctly

    Only ever transport damaged batteries in an appropriate acid-resistant receptacle. • Wash all objects that have come into contact with acid with lots of water. Disposing of dead or damaged batteries correctly Dead or damaged batteries can be given back to your dealer or directly to Invacare®.

  • Page 86: Care And Maintenance

    Care and maintenance NOTE: Have your vehicle checked once a year by an authorised Invacare® dealer in order to maintain it's driving safety and roadworthiness. Cleaning the vehicle When cleaning the vehicle, pay attention to the following points: • Only use a damp cloth and gentle detergent.
  • Page 87 Maintenance Jobs Seat and backrest padding: - Check for perfect condition. Side part and armrest: - Are all fastening elements installed? - Can armrests / side parts be removed and installed without too much physical effort? - Are armrests secured in their positions? Legrests: - Do legrests lock into place without any problem? (Only applies to detachable legrests)
  • Page 88 - Clean all parts carefully. When necessary Have your vehicle inspected and serviced once a year by your authorised dealer. A complete checklist of necessary maintenance work can be found in the Service Manual, which can be obtained from Invacare®.

  • Page 89: Repair Instructions

    "Technical Specifications" on page 103, or consult the Service Manual, available from Invacare® (in this connection please see the addresses and phone numbers in section "How can you get in touch with Invacare®?" on page 2). In case you require assistance, please contact your Invacare® Dealer.

  • Page 90: Repairing A Flat Tyre At The Back (Tyre Type 3.00-8")

    11.1.1 Repairing a flat tyre at the back (tyre type 3.00-8") Injury hazard! If the wheel has been insufficiently secured during assembly, it can become loosened during driving! • When refitting the drive wheels, tighten the Torx screw that secures the wheel to the hub to a torque of 30 Nm! •...
  • Page 91 Removing the wheel • Jack the vehicle up and place a block of wood underneath it to prop it up. • Remove the countersunk screw (1) using the Torx bit. • Remove the wheel from the axle. EXPLOSION HAZARD! The wheel will explode if the air pressure is not released from the tyre before disassembling the wheel rim! •...
  • Page 92 NOTE In case the old inner tube is to be repaired and used again, and it happens to get wet during repair, then it is easier to re-fit it if you powder it lightly with talcum powder. NOTE Re-assembly is done in reverse order. Make sure that the wheel is put back on the same side it was on, and that it runs in the same direction it did before it was removed.

  • Page 93: Transport

    Transport CAUTION: Injury hazard or material damage if an electric wheelchair which is fitted with a table is transported in a vehicle! • If a table is fitted, always remove it before transporting the wheelchair! 12.1 Transferring the wheelchair to a vehicle WARNING: Danger of tipping over, if the wheelchair is transferred to a vehicle using a ramp that exceeds the maximum safe slope, or if the backrest is not in an upright position during transfer!
  • Page 94 • Drive or push your wheelchair into the transport vehicle using a suitable ramp.

  • Page 95: Use Of The Wheelchair As A Seat In A Vehicle

    (UK for example), but may also be obtained from Invacare® as an option in other countries. This electric wheelchair complies with the requirements of ISO 7176-19:2001 and may be used as a vehicle seat in connection with an anchoring system that has been checked and approved in accordance with ISO 10542.
  • Page 96 Caution: There is a danger of injury if the wheelchair is not properly secured during use as a vehicle seat! • If possible, the user should always leave the wheelchair to use a vehicle seat and the safety belts provided with the vehicle! •...

  • Page 97: 12.2.1 How The Wheelchair Is Anchored In A Vehicle For Use As A Vehicle Seat

    12.2.1 How the wheelchair is anchored in a vehicle for use as a vehicle seat The electric wheelchair is fitted with four anchoring points, which are labelled with the symbol shown on the right. Snap hooks or belt loops can be used for fixation.

  • Page 98: 12.2.2 How The User Is Secured Within The Wheelchair

    12.2.2 How the user is secured within the wheelchair CAUTION: there is a danger of injury if the user is not properly secured within the wheelchair! • Even if the wheelchair is fitted with a posture belt, this is no substitute for a proper safety belt which complies with ISO 10542 in the transport vehicle! Always use the safety belt installed in the transport vehicle ! •...
  • Page 99 Seat belts may not be held at a distance The pelvic belt should be positioned in the from the user's body using parts of the area between the user's pelvis and thighs wheelchair such as armrests or wheels. so that it is unobstructed and not too loose. The ideal angle of the pelvic belt to the horizontal is between 45°...

  • Page 100: Securing The Wheelchair For Transport Without Passengers

    12.3 Securing the wheelchair for transport without passengers CAUTION: Injury hazard! • If you are unable to fasten your electric wheelchair securely in a transport vehicle, we recommend that you do not transport it! • Before transporting your wheelchair, make sure the motors are engaged and that the Joystick Box is switched off.

  • Page 101: Refurbishment

    Cleaning and disinfection. Please see chapter "Care and maintenance" on page 86. • Inspection according to service plan. Please consult service instructions, available from Invacare®. • Adaptation to the user. Please see chapter "Adjusting the wheelchair to the user's seating...

  • Page 102: Disposal

    Electric components and printed circuit boards are disposed of as electronic scrap. • Exhausted or damaged batteries can be returned to your medical equipment supplier or Invacare®. • Disposal must be carried out in accordance with the respective national legal provisions.

  • Page 103: Technical Specifications

    Technical Specifications Permissible Operating and Storage Conditions Temperature range for operation • -25 … +50 °C according to ISO 7176-9: Temperature range for storage • -40 … +65 °C according to ISO 7176-9: Electrical System Motors • 2 x 220 W Batteries •...
  • Page 104 Driving Characteristics Speed • 8 km/h Max. tilt-resistant climbing power • 11,4% Max. surmountable obstacle • 10 cm height Turning radius • 83 cm Range according to ISO 7176 *** • 30 km Dimensions Max. Overall height • 106 cm Width of the drive unit •...
  • Page 105 **** Measured without seat cushion ***** The actual kerb weight depends on the fittings your mobility aid has been supplied with. Every Invacare® mobility aid is weighed when leaving the works. Please refer to the nameplate for the kerb weight (including batteries) measured.

  • Page 106: Inspections Performed

    It is confirmed by stamp and signature that all jobs listed in the inspection schedule of the Service and Repair Instructions have been properly performed. The list of the inspection jobs to be performed can be found in the Service Manual which is available through Invacare®. Delivery Inspection...

Table of Contents