Radio Receiver Programming - Chamberlain CSW200UL8 Owner's Manual

ADJUSTMENTS

RADIO RECEIVER PROGRAMMING

The receiver can be used as a single, two, or three channel
receiver and is compatible with Security+ 2.0™ remote controls
ONLY. Each channel is compatible with a certain number of
remote controls and keypads. Refer to the list below:
• CH1: 50 remote controls and 2 keypads
• CH2: 20 remote controls and 2 keypads
• CH3: 20 remote controls and 2 keypads
When the channel has reached full capacity for remote controls,
all LEDs will blink 3 times. When the channel has reached full
capacity for keypads, all LEDs will blink 4 times. Additional
accessories can be programmed, however, the newly programmed
accessory will replace the first programmed accessory.
NOTE: The receiver will only allow you to program a button on the
remote control to one channel at a time. For example, if the button
on the remote control is already programmed to channel 1 and
then is programmed to channel 3, the button will be erased from
channel 1 and will only work on channel 3.
IMPORTANT: Remote control is NOT provided.
Program a Single Button Remote Control
1 Press and release the Learn button for the selected channel on
the receiver. The corresponding LED will glow steadily for 30
seconds.
2 Within 30 seconds press and hold the button on the remote
control that you wish to program to the receiver.
3 Release the remote control button when the LED on the receiver
blinks, then turns off. Programming is complete.
Repeat the steps above for each remote control you would like to
program.
Program a 3-Button Remote Control as OPEN, CLOSE,
and STOP
NOTE: In order for the operator to function with a 3 button remote,
the OmniControl™ Board must be installed. Connect CH1 to the
Open input, connect CH2 to the CLOSE input, and connect CH3 to
the STOP input of the OmniControl™ Board.
1 Press and release the CH1 Learn button on the receiver.
2 Within 30 seconds press the desired OPEN button on the
remote control.
3 Press and release the CH2 Learn button on the receiver.
4 Within 30 seconds press the desired CLOSE button on the
remote control.
5 Press and release the CH3 Learn button on the receiver.
6 Within 30 seconds press the desired STOP button on the remote
control.
NOTE: If a remote control button is not pressed within 30 seconds,
the LED next to the selected Learn button will turn OFF. In that
case, repeat the programming.
To Erase the Memory
1 Press and hold the Learn button for the channel you want to
erase. Release the button when the corresponding LED turns
off; the memory has been erased.
Optional Remote Controls - See Accessories
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is NOT connected BEFORE installing the
receiver.
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is
properly adjusted, and there are no obstructions to door
travel.
• ALWAYS keep gate or garage door in sight until completely
closed. NEVER permit anyone to cross path of moving gate or
door.
NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada (IC) license-exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
CH1 Learn Button
NOTE: Disconnect the
secondary receiver
when using a primary/
secondary setup.
29
CH2 Learn Button
CH3 Learn Button
CH1 CH2 CH3