Diagrams; Circuit Boards Location - Sony RCD-W2000ES Sevice Manual
Compact disc recorder
Hide thumbs
Also See for RCD-W2000ES:
- Operating instructions manual (44 pages) ,
- Limited warranty (1 page)
Table of Contents
Advertisement
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and
1
/
W or less unless otherwise
4
specified.
•
%
: indicates tolerance.
•
: internal component.
¢
• C : panel designation.
• 5 : fusible resistor.
Note:
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• B : B– Line.
• H : adjustment for repair.
• AC voltage readings in the bias oscillator with a level
meter.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : STOP
(
) : PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
6-1. CIRCUIT BOARD LOCATION
CLAMP MOTOR board
BD board
SENSOR 2 board
SENSOR board
OUT SW board
INIT/COUNT SW board
LOAD MOTOR board
SECTION 6
DIAGRAMS
• Signal path.
F
: LINE (ANALOG)
J
: CD PLAY (ANALOG)
c : CD PLAY (DIGITAL)
I : CD REC
For printed wiring boards.
Note:
• X : parts extracted from the component side.
• x : parts extracted from the conductor side.
•
: parts mounted on the conductor side.
x
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B)
pattern face are indicated.
Parts face side:
Parts on the parts face side seen from the
(Side A)
parts face are indicated.
• Indication of transistor
C
Q
These are omitted
B
C
E
B
E
These are omitted
IN SW board
LED board
POWER SW board
RM board
HP board
CONNECTOR board
CD SW board
CD-R board
DISPLAY board
• WAVEFORMS
– BD BOARD –
1
IC101 el FE
VOL/DIV : 0.05V AC
TIME/DIV : 2msec
2
IC101 ra TE
VOL/DIV : 0.1V AC
TIME/DIV : 2msec
3
IC101 rd RFDC
VOL/DIV : 0.2V AC
TIME/DIV : 1 µ sec
4
IC101 t; RFAC
VOL/DIV : 0.5V AC
TIME/DIV : 1 µ sec
5
IC101 us
33.8688MHz
VOL/DIV : 1V AC
TIME/DIV : 20nsec
AC board
D-AUDIO board
MAIN board
53
53
– CDR BOARD –
1
IC101 9 TE
1.5 Vp-p
0.1 Vp-p
VOL/DIV : 0.5V AC
TIME/DIV : 1msec
2
IC101 0 FE
1.2 Vp-p
0.2 Vp-p
VOL/DIV : 0.5V AC
TIME/DIV : 1msec
3
IC101 rk MCLK1
4.4 Vp-p
0.6 Vp-p
34.5744MHz
VOL/DIV : 2V AC
TIME/DIV : 20nsec
4
IC101 i; EQRF
1.0 Vp-p
1.0 Vp-p
VOL/DIV : 0.5V AC
TIME/DIV : 500nsec
5
XTAL
IC201
168
3.7 Vp-p
5.8 Vp-p
33.8688MHz
VOL/DIV : 2V AC
TIME/DIV : 20nsec
6
IC501 yj XTAL
1.3 Vp-p
20MHz
VOL/DIV : 0.5V AC
TIME/DIV : 50nsec
RCD-W2000ES
– MAIN BOARD –
1
IC1 qd XOUT
3.9Vp-p
5MHz
VOL/DIV : 1V AC
TIME/DIV : 0.1 µ sec
– DISPLAY BOARD –
1
IC760 yh OSCO
5.0Vp-p
0.42 µ sec
VOL/DIV : 2V AC
TIME/DIV : 0.2 µ sec
Advertisement
Table of Contents
