Page 1 Rider’s Manual (US Model) K 1200 R BMW Motorrad...
Page 3: Welcome To Bmw
We congratulate you on your authorized BMW motorcycle choice of a motorcycle from retailer will gladly provide BMW and welcome you to the advice and assistance. community of BMW riders. Familiarize yourself with your We hope you enjoy reading new motorcycle so that you this Rider’s Manual and wish...
Page 4: Table Of Contents
Electronic immobilizer ... 35 First time out ....56 Hazard warning flashers 36 Before you start .... 57 Welcome to BMW ... 1 Tripmaster ....37 Starting ......61 General information ..4 Emergency ON/OFF Riding ......63 switch ......
Page 5 ....... 140 Clutch ......96 Riding specifications .. 141 Wheels ......98 9 Service ..... 143 Front-wheel stand ..107 BMW Motorrad Rear-wheel stand ..108 Service ....... 144 Bulbs ......109 Confirmation of Jump starting ..... 115 maintenance work ..148 Battery .......
Page 6: General Information
BMW When the time comes to sell motorcycle retailer; c Indicates the end of an your BMW, please remember optional accessories item of information. to hand over this Rider’s have to be retrofitted to Manual; it is an important part the motorcycle.
Page 7 ESA Electronic Suspension manual on account of country- Adjustment. specific differences. The high safety and quality If your BMW was supplied with standards of BMW motorcy- DWA Anti-theft alarm equipment not described in cles are maintained by this Rider’s Manual, you will...
Page 8 Have all maintenance and – Boots quential damage and thus repair work carried out con- constitute a safety risk. BMW firmed in the "Service" chapter This applies even to short recommends that you have 148) in this manual.
Page 9: Overview
General view, left side ....9 General view, right side ....11 Underneath the seat ....13 Handlebar fitting, left ....14 Handlebar fitting, right ....15 Instrument panel ......16 Headlight ........17 Overview...
Page 11: General View, Left Side
General view, left side 1 Clutch fluid reservoir 2 Rear spring preload adjustment ( 3 Seat lock ( 44) beneath rear light 4 Rear shock absorber damping adjustment 5 Power socket ( 6 Coolant fill opening (...
Page 13: General View, Right Side
General view, right side 1 Display for engine oil level 2 Fill location, fuel tank 3 Battery compartment 116) 4 Brake-fluid reservoir, front 5 Type plate 6 Vehicle identification number 7 Brake-fluid reservoir, rear...
Page 15: Underneath The Seat
Underneath the seat 1 Fill location, engine oil 2 Toolkit ( 3 Anti-theft alarm 4 Helmet holder (...
Page 16: Handlebar Fitting, Left
Handlebar fitting, left 1 Button, Tripmaster ( 2 Pushbutton, hazard warning flashers ( 3 Button, ESA 4 Pushbutton, horn 5 Pushbutton, left turn indicators ( 6 Switch, high-beam headlight and headlight flasher (...
Page 17: Handlebar Fitting, Right
Handlebar fitting, right 1 Emergency ON/OFF switch ( 2 Pushbutton, starter 3 Switch, grip heating 4 Pushbutton, right turn indicators ( 5 Pushbutton, turn indicators off (...
Page 18: Instrument Panel
Instrument panel 1 Speedometer 2 Rev. counter 3 Warning and indicator lights ( 4 Multifunction display 5 Indicator light DWA sensor for instrument panel lighting 6 Adjuster, clock ( The instrument panel lighting is equipped with an automatic day and night switchover.c...
Page 19: Headlight
Headlight 1 Low-beam headlight 2 High-beam headlight 3 Side lights...
Page 21: Status Indicators
Multifunction display ....20 Warning and indicator lights ..20 Function indicators ...... 20 Warning indicators ....... 21 warning indicators ..27 Status indicators...
Page 22: Multifunction Display
Multifunction display Warning and indicator Function indicators lights Fuel capacity The horizontal bars indi- cate the level of fuel in the tank. If only four bars are dis- played, the reserve level has been reached. Gear indicator The gear indicator shows which gear is selected.
Page 23: Warning Indicators
Warning indicators Warnings are displayed by means of symbols in the multifunction display. In some cases, an additional general warning light lights up red or yellow. A number of warnings may be issued simultaneously.
Page 24 Overview The warnings are listed in the table below, along with the page numbers of the pages you can refer to for more information. Light Symbol Meaning Explanations Ignition key not authorized. Low-beam headlight, high-beam headlight, parking light or turn indicator lamp defective.
Page 25 Light Symbol Meaning Explanations Battery is no longer being charged. Brake switch defective. 1 flash per second ABS starting-off test not completed. ( 4 flashes per second ABS self-diagnosis not completed. Relay for ABS warning lights defective. 1 flash per second ABS function not available.
Page 26 • If possible, ride in the part- authorized BMW motorcycle Do not run the fuel tank dry.c load range to cool down the retailer ( 36).
Page 27 2 seconds after the engine engine damage. preferably an authorized starts. If the "engine oil pressure" BMW motorcycle retailer. warning is issued, do not continue to ride if a check shows that the engine oil level is correct.c...
Page 28 BMW motorcycle retailer. preferably an authorized Low-beam headlight, high- BMW motorcycle retailer. Battery charge current beam headlight, side-light or General warning light Bulb failure turn-indicator bulb defective.
Page 29: Abs Oe Warning Indicators
Brake switch defective or BMW motorcycle retailer. incorrectly adjusted. BMW Integral ABS detects the warning light driver’s braking request by the ABS warning light flashes pressure build-up from the once per second.
Page 30 ABS warnings not Avoid hard braking whenever available. The failure of Only residual braking function possible. Brake early, as functions of the BMW Integral available in both brake increased braking force is ABS cannot be displayed. circuits, because self-diagno- required.c...
Page 31 ABS function nor 1 time per second. the brake booster is available. Without the ABS func- Fluid level in BMW Integral tion, the wheels may lock Without the ABS func- ABS too low. up during very hard braking, tion, the wheels could causing accidents.
Page 32 • Check brake pad thickness signs of brake fluid preferably an authorized 94). escaping. BMW motorcycle retailer. • Have worn brake pads replaced as soon as If any of the above criteria are possible by a specialized General warning light...
Page 33 ABS warning light flashing 4 times per second. – Fluid level in the BMW Integral ABS is too low, indicated by the general and ABS warning lights flashing once per second.
Page 35: Operation
Ignition switch and Shock absorbers ......48 steering lock ......... 34 ........... 49 Electronic immobilizer ....35 Wheels ........... 51 Hazard warning flashers ....36 Operation Tripmaster ........37 Emergency ON/OFF switch ..38 Grip heating ......39 Clock ..........40 Handlebar levers ......
Page 36: Ignition Switch And
Ignition switch and Switching on ignition Switching off ignition steering lock Keys You receive one master key and one spare key. If a key is lost, please note the informa- tion on the electronic immobi- lizer (EWS) ( 24). Ignition key and steering •...
Page 37: Electronic Immobilizer
When you prop the motorcycle on the side The electronic immobilizer stand, the surface of the helps protect your BMW ground will determine whether motorcycle from theft, and this it is better to turn the handle- enhanced security is at your bars to the left or right.
Page 38: Hazard Warning Flashers
You can obtain replacement these signals are specific to keys only through an autho- your motorcycle and they are rized BMW motorcycle retailer. transmitted via the ring aerial The keys are part of an inte- in the ignition lock. The ignition...
Page 39: Tripmaster
Tripmaster » The hazard warning flashers continue to operate. Selecting display » Left/right turn indicator lights off. You can also switch on the hazard warning flash- ers by simultaneously pressing the buttons for the left and right turn indicators.c » The following appear in the The hazard warning display field 2 in this order: flashers place a strain on...
Page 40: Emergency On/Off Switch
Operating range The Tripmaster registers that you have refueled when approximately 3.2 quarts (3 liters) have been added. Resetting trip meter • Switch on the ignition. • Select the desired tripmeter. • Press the Tripmaster button 1 for longer than Actuating the emergency 2 seconds.
Page 41: Grip Heating Oe
ON/OFF switch to the B position while The increased power the ignition is switched on, the consumption caused by BMW Integral ABS remains operating the heated hand 1 Grip heating switch operational ( 75).c grips can lead to the battery discharging on journeys in the lower engine speed range.
Page 42: Clock
Clock » The hour increments by one each time you press the Attempting to set the button. clock while riding the mo- • Press button 1 for longer torcycle can lead to accidents. than 2 seconds. Set the clock only when the »...
Page 43: Lights
Adjusting handbrake Low-beam headlight » Turn clockwise: reach is lever increased. The low-beam headlight » Turn counter-clockwise: switches on automatically Adjusting the brake lever reach is reduced. when you start the engine. while the motorcycle is being ridden can lead to The adjusting screw has With the engine switched accidents.
Page 44 » High-beam headlight again. a specialized workshop, switched off. » Parking lights switched off. preferably an authorized • Press the bottom part of BMW motorcycle retailer. switch 1 for the high-beam headlight. » Headlight flasher.
Page 45: Turn Indicators
Turn indicators Switching off turn indicators Switching on turn indicators • Press right-hand turn indicator button 2. » Right-hand turn indicator • Press cancel button 3. switched on. » Turn indicator off. • Press left-hand turn indica- » Indicator light for right-hand »...
Page 46: Seat
Seat Installing seat • In doing so, press the seat downwards for support. If too much pressure is Removing seat applied in the forward direction, there is a danger that the motorcycle will be pushed off its stand. Make sure that the motorcycle is steady on its stand.c •...
Page 47: Helmet Holder
Helmet holder • Pull the steel cable through the helmet and hook it into the bracket. • Install the seat. On the right-hand side of the motorcycle, the helmet could be damaged by heat from the end muffler. Only attach the helmet to the •...
Page 48: Luggage Loops
Luggage loops To make the loops accessible: • Remove the seat and turn it around. • Pull the loops 1 from the retaining brackets. 2 • Turn the seat over and refit. Mirrors Adjusting mirrors • Push the protective cap 1 up over the threaded fastener Loops 1 for attaching luggage on the mirror arm.
Page 49: Spring Preload
Spring preload Basic setting for one-up riding: • Turn handwheel 1 as far as Adjusting spring preload possible in direction of arrow on rear wheel LOW. • Turn handwheel 15 clicks in Adjusting the spring pre- direction of arrow HIGH. load while the motorcycle is being ridden can lead to One click corresponds to...
Page 50: Shock Absorbers
Shock absorbers • Adjust the rear shock Basic setting for one-up riding: absorber, using a screw- • Turn adjusting screw 1 all Adjusting rear shock driver to turn adjusting the way in the direction absorber screw 1. indicated by the H arrow. The damping must be adapted •...
Page 51: Esa Oe
Adjusting shock absorbers Using the ESA (Electronic Suspension Adjustment) you can conveniently adapt your motorcycle to different driving conditions. Calling up settings 2 set damping 3 set spring preload Three adjustments are possi- If button 1 is not pressed for ble;...
Page 52 If button 1 is not pressed for Solo operation longer than one second, the shock absorbers are set as Solo operation with displayed. luggage During the setting procedure, Operation with passen- the display flashes. ger (and luggage) Adjusting spring preload The spring preload cannot be adjusted while the motorcycle •...
Page 53: Wheels
– One-up The required tire pressure can – One-up with luggage be found in the technical data – Two-up (with luggage) section ( 130). At high road speeds, tire If button 1 is not pressed for valves have a tendency longer than one second, the to open as a result of centrifu- spring preload is set as dis-...
Page 55: Riding
Safety instructions ....... 54 Safety check ......... 56 First time out ......... 56 Before you start ......57 Starting .......... 61 Riding ..........63 Running in ........63 Shifting gear ......... 64 Placing on side stand ....67 Removing from side stand ..69 Placing on center stand ...
Page 56: Safety Instructions
Safety instructions Alcohol and drugs Inhaling the exhaust fumes therefore repre- Even small amounts of Speed sents a health hazard and can alcohol or drugs will ad- If you ride at high speed, even cause loss of conscious- versely affect your perception always bear in mind that ness with fatal consequences.
Page 57 Catalytic converter Risk of fire Tampering with engine management system If misfiring causes unburned Temperatures at the exhaust fuel to enter the catalytic are high. Modifications to the en- converter, there is a danger of If highly flammable mate- gine electronics control overheating and damage.
Page 58: Safety Check
Safety check At regular intervals: The description of the BMW – Engine oil level (every time Integral ABS starts on page Prior to every journey you refuel) ( 75). Use the following checklist to – Brake pads (every second/ BMW Integral ABS incor-...
Page 59: Before You Start
(EWS) symbol is displayed. 24). Battery charge current • Emergency ON/OFF symbol is displayed. switch 1 in operating position A. • Switch on the ignition. » Pre-ride check is performed. » With BMW Integral ABS ABS self-diagnosis is performed.
Page 60 Phase 2 Phase 3 Phase 4 (only with DWA General warning light A warning light defect is The "DWA" battery warn- lights up in yellow. displayed. ing for the anti-theft alarm Engine electronics appears if the voltage level of If one of the warning symbol is displayed.
Page 61 Once the pre-ride check com- 4 times per second. pletes, the various gauges and indicators show their current Self-diagnosis is in progress. The BMW Integral ABS per- values. forms self-diagnosis and a If the engine is started Phase 2 pull-away test to ensure its...
Page 62 When gear engaged. Switch on the BMW Integral ABS is still in the self-diagnosis completes, ignition before you pull the residual braking function apply the brakes, disengage clutch.
Page 63: Starting
Starting The start attempt is auto- matically interrupted if Do not turn the throttle the battery voltage is too low. twistgrip when starting Recharge the battery ( 117) the engine. At ambient tem- before you start the engine, or peratures below 32 °F (0 °C), use jump leads and a donor disengage the clutch after battery to start (...
Page 64: Troubleshooting Chart
Troubleshooting chart Fault: Engine does not start or only starts with difficulty. Possible cause Remedy see page Emergency ON/OFF switch Set the emergency ON/OFF switch to its activated RUN position Side stand extended, Retract the side stand fully gear engaged Gear engaged, clutch not Select neutral or pull clutch lever disengaged...
Page 65: Riding
The BMW Integral ABS checks wear. the ABS sensors when you Keep to the guideline values pull away after starting. The as stated below.c ABS warning light then goes out and the BMW Integral ABS is active.
Page 66: Shifting Gear
Brake pads Tires Shifting gear New brake pads must "bed New tires have a smooth sur- Engine speed down" and therefore do not face. This must be roughened Do not use the high end of the achieve their optimum friction by riding in a restrained man- engine-revolutions range in levels during the first 300 miles...
Page 67: Gear Shifts
Gear shifts Attempting to shift gear with the clutch engaged can damage the transmission. Always disengage the clutch in order to shift gears.c The gear indicator in the multifunction display tells you which gear is engaged.c...
Page 69: Placing On Side Stand
Placing on side stand If the motorcycle is on the The side stand is de- side stand, it depends on signed to support only No secure stance is the features of the ground the weight of the motorcycle. possible on poor ground whether it is better to turn the Do not lean or sit on the conditions.
Page 71: Removing From Side Stand
Removing from side • Hold the motorcycle upright and balanced. stand • Seat yourself and fold back With the ignition switched the side stand with your left off, there is no brake foot. power assistance; the motor- An extended side stand cycle can begin to roll.
Page 73: Placing On Center Stand Oe
Placing on center • Place the full weight of your body on the center stand, stand while pulling the motorcycle No secure stance is to the rear (arrow). possible on poor ground • Check that the motorcycle is conditions. standing firmly. Always check that the ground The center stand can re- under the stand is level and...
Page 75: Removing From Center Stand Oe
Removing from center Fuel grade • Make sure that the center stand is fully retracted.. stand Leaded fuel destroys the catalytic converter. Fuel Brake servo assistance is Use only unleaded fuel.c not available when the Fuel is a fire hazard and ignition is off;...
Page 76: Brake System
Capacity Brake system • Open the protective cap. – Usable volume of fuel: 5 gal • Open the fuel tank cap with General (19 liters) the ignition key by turning – Of which reserve volume: counter-clockwise. Descending mountain approx. 1 gal (4 liters) passes The fuel gauge in the If only the rear brake is...
Page 77 It is particularly important to BMW Integral ABS applied.c check the brake pads and In extreme situations, it takes discs after repair and Salt on brakes...
Page 78 The hydraulic pump in the Making full use of the motorcy- weight and momentum take BMW Integral ABS boosts the cle’s technical braking capac- over and even BMW Integral braking force acting on the ity will minimize braking...
Page 79 BMW Integral ABS, the brake Without the ABS function Consequently, ABS does not circuits concerned only have the wheels may lock up intervene until very late, if at all.
Page 80 As the residual braking function means that the lever path before the brake pressure is built up can be longer, we recommend setting a larger lever path at the hand- brake lever ( 41).c In the case of residual braking function in both brake circuits, no pump noise can be heard when the brake lever is operated.c...
Page 81: Accessories
General instructions ....80 Power socket ........ 80 Luggage system ...... 83 Accessories...
Page 82: General Instructions
Power socket motorcycle that are approved tion with BMW motorcycles by BMW for this purpose. Your without constituting a safety authorized BMW motorcycle hazard. County-specific offi- retailer is the right source for...
Page 83 Operating electrical – do not impede the rider accessories – do not restrict or obstruct You can start using electrical the steering angle and han- accessories only when the dling characteristics ignition is switched on. The – cannot be trapped accessory remains operational Improperly routed cables if the ignition is subsequently...
Page 85: Luggage System Oa
Luggage system • Pack heavy items at the bottom and toward the Correct loading inboard side. • Load the left-hand and right- Fitting a luggage system hand cases with a maxi- will affect the handling of mum of 18 lbs (8 kg) each. your motorcycle.
Page 86 Removing cases • Pull the case out of the upper mounting. • Lift the case out of the lower mounting. Adapting cases • Open the case. • Turn lock barrel toward • Loosen screw 1. RELEASE. • Set the height of the bracket. •...
Page 87 • Turn lock barrel toward » The catches can be heard to OPEN. lock into place. • Pull the gray release lever • Press the catches 3 of the upwards. lock straps into the retainers 2. » The catches can be heard to lock into place.
Page 88 • Pull out the lock straps upwards. » The maximum volume has been set. • Close the lock straps. • Press the lock straps against the case body. » The case volume is adapted to the contents.
Page 89: Maintenance
Toolkit ..........89 Engine oil ........89 Coolant .......... 92 Brakes ........... 93 Clutch ..........96 Wheels ........... 98 Front-wheel stand ...... 107 Rear-wheel stand ....... 108 Bulbs ..........109 Jump starting ......115 Battery ......... 116 Splash guard ....... 120 Maintenance...
Page 90 You can obtain a The types of screws used for copy from your authorized the components concerned BMW motorcycle retailer. are listed in ( 128). You can use this chart to set aside the required tools.
Page 91: Toolkit
The oil level depends on from your authorized the oil temperature. The BMW motorcycle retailer. higher the temperature the higher the oil level in the oil Contents of supplement kit tank. 1 Screwdriver blade...
Page 92 After longer motorcycle • Switch off the ignition. 2 maximum engine oil level immobilization periods, • Read off the oil level. 3 minimum engine oil level oil can collect in the oil pan; this must be pumped into the The oil level must be located oil tank before the reading is between the MIN and taken.
Page 93 Draining off engine oil The engine can seize if the oil level is low, and • Remove the seat ( 44). this can lead to accidents. • Press the retainer of the Always make sure that the oil clear hose 2 on the left and level is correct.c right and pull out of the oil tank upwards.
Page 94: Coolant
Coolant Topping up coolant Checking coolant level Check the coolant level at regular intervals. 2 maximum coolant level 3 minimum coolant level Do not add coolant to the cooling system when the The coolant level must be engine is hot. Escaping located between the MIN and coolant can cause burns.c 1 Display for coolant level.
Page 95: Brakes
» The hydraulic pump must be Brakes authorized BMW motorcycle heard to run. retailer. A properly functioning brake Brake pads system is a basic requirement Vehicles without ABS...
Page 96 • Have the brake pads replaced by a specialized workshop, preferably an authorized BMW motorcycle • Visually inspect the left and • Perform a visual inspection retailer. right brake pads to ascertain of the brake pad thickness Checking brake pad their thickness.
Page 97 • Have the brake pads • Place the handlebars in a replaced, preferably by an straight ahead position. authorized BMW motorcycle • Read off the brake fluid level retailer. at the reservoir. Checking brake fluid...
Page 98: Clutch
• Check the brake system for preferably an authorized certified workshop, leaks. BMW motorcycle retailer. preferably an authorized • Have the fault rectified as BMW motorcycle retailer. soon as possible by a specialized workshop, preferably an authorized BMW motorcycle retailer.
Page 99 MIN mark, the clutch system straight ahead position. must be checked immediately. • Read off the clutch fluid level • Have the fault remedied as at the reservoir. quickly as possible by a certified workshop, prefera- bly an authorized BMW motorcycle retailer.
Page 100: Wheels
Wheels Checking rims The handling characteris- • Place the motorcycle on the tics of your motorcycle For each size of tire BMW center stand or side can deteriorate even before Motorrad tests certain makes, stand, ensuring that the the legally prescribed mini- and approves those that it ground is firm and level.
Page 101: Removing Front Wheel
We recommend using BMW Integral ABS, in the the BMW rear-wheel course of the procedure stand for this purpose.c described below. Take care not to damage the •...
Page 102 • Force brake calipers 3 • Lift the motorcycle using the stand : if the motorcycle is slightly apart by rocking BMW Motorrad front-wheel raised too far at the front the them back and A against the stand ( 107) until the front center stand will lift clear of the brake disks 4.
Page 103: Installing Front Wheel
22 open-end or ring wrench. The left-hand axle tightening torques, on The BMW special tool number clamping screw fixes the 128).c is 363690 and the adapter is threaded bush in place in the...
Page 104 • Roll the front wheel into the work, parts of the front front wheel guide. brake, in particular of the BMW Integral ABS, can be damaged. Take care not to damage the brake system, in particular the ABS sensor with cable and the ABS sensor ring.c...
Page 105: Removing Rear Wheel
With BMW Integral ABS We recommend using • Switch on the ignition. the BMW rear-wheel • Wait for self-diagnosis to stand ( 108) for this complete ( 59). purpose.c • Firmly pull the handbrake lever a number of times, until the pressure point is perceptible.
Page 106: Installing Rear Wheel
• Roll the rear wheel out Do not remove the seal- toward the rear. ing grease from the • If the BMW Motorrad rear- clamp.c • Remove the mounting wheel stand is used: ( 108) bolts 5 of the rear wheel,...
Page 107 Screw connections tight- • Lift the rear wheel onto the ened with the incorrect rear wheel hub. torque can come loose or • If the BMW Motorrad rear- damage the screw connection wheel stand is used: attach itself. the retaining disk again.
Page 108 • Tighten screw 4 for the bracket of the end silencer in the rear footrest to 16 Nm. • Align the clamp 3 on the end • Push the muffler cover 2 with muffler with the mark A guides A into the (arrow) on the Lambda brackets B.
Page 109: Front-Wheel Stand
Front-wheel stand A front-wheel stand for simple, safe changing of the front wheel is available from BMW Motorrad. The BMW special tool number is 363971 • Place the motorcycle on the and the front-wheel stand is center stand or suitable available from your authorized auxiliary stand, e.g.
Page 110: Rear-Wheel Stand
Installing rear-wheel In the case of BMW Inte- When the motorcycle is stand gral ABS, the ABS sensor standing on its center ring can be damaged. stand: if the motorcycle is Only push the mounting pin so raised too far at the front the...
Page 111: Bulbs
Bulbs Information on bulbs The "bulb defect" symbol appears in the display if a bulb is defective. If the brake or rear light fails, the general warning light also lights up in yellow. If the rear light fails, the brake light is used as a substitute in •...
Page 112 Replacing low-beam You will find an overview headlight bulb of the types of bulb used on ( 139).c If it is not standing firmly, Do not touch the glass of the motorcycle could new bulbs with your fin- topple in the course of the gers.
Page 113 • Disconnect plug 4. • Remove bulb 6. • On assembly, make sure that the lug 7 points Installation is the reverse of the upwards. removal procedure. Replacing high-beam headlight bulb If it is not standing firmly, the motorcycle could topple in the course of the operations described below.
Page 114 The bulb is pressurized • Pull out the light housing and can cause injuries toward the front and tilt it when damaged. slightly downward. Wear protective goggles and • Remove the bulb holder 2 gloves when changing from the headlight housing bulbs.c by turning it counter-clock- wise.
Page 115 Replacing brake light and rear light bulbs If it is not standing firmly, the motorcycle could topple in the course of the operations described below. Make sure that the motorcycle is steady on its stand.c • Press the light housing into •...
Page 116 • Press the bulb into its socket and turn it counter-clock- wise to remove. Installation is the reverse of the removal procedure. • Use a clean, dry cloth to hold the new bulb. Replacing front/rear turn • Remove screw 1. •...
Page 117: Jump Starting
Jump starting Use only jump leads fitted with discharged battery and the fully insulated crocodile clips other end to the positive The wires leading to the at both ends.c terminal of the donor battery. power socket do not • Then connect one end of the Jump-starting with a have a load-capacity rating black jump lead to the nega-...
Page 118: Battery
Touching live parts of the BMW Motorrad has de- – Keep the surface of the ignition system with the veloped a trickle-charger battery clean and dry.
Page 119 The motorcycle's on- battery is completely flat. Your authorized BMW board electronics know motorcycle retailer will be when the battery is fully • Charge the disconnected happy to provide information charged.
Page 120 Charging disconnected Removing battery battery The types of screw used The battery has to be are listed on ( 128).c recharged at regular If it is not standing firmly, intervals in the course of a the motorcycle could lengthy period of disuse. topple in the course of the See the instructions for caring operations described below.
Page 121 Installing battery • Remove the negative cable 2 • Install the positive cable first first. and tighten hand-tight. The types of screw used • Then remove the positive • Then install the negative are listed, complete with cable 3. cable and tighten hand-tight. tightening torques, on •...
Page 122: Splash Guard
Splash guard A splash guard is supplied with the motorcycle; if required, this can be fitted to the license plate holder. • Use the screws 1 to fit the splash guard on the license plate holder from below.
Page 123: Care
Cleaning and care ...... 122 Storing ......... 125 Returning to use ......125 Care...
Page 124: Cleaning And Care
We recommend that you use We recommend that you use After washing the motorcycle, the cleaning and care prod- BMW insect remover to soften dry the brakes by braking.c ucts you can obtain from your and wash off insects and...
Page 125 BMW paint, especially if your motor- parts. Even fly-remover pads vehicle shampoo. Use chrome cycle is ridden in areas with or cleaning pads with hard polish for additional treatment.
Page 126: Tire Pressures
BMW vehicle wax works specifications with occur. These include, e.g., or agents that contain car- original BMW paints.
Page 127: Storing
• Remove the battery ( 118). shop, preferably your autho- • Spray the brake and clutch rized BMW motorcycle retailer. lever pivots and the center Combine work for storing/re- and side stand pivots with a turning to use with a mainte- suitable lubricant.
Page 129: Technical Data
Threaded fasteners ..... 122 Tire pressures......124 Engine .......... 125 Power transmission ....126 Frame and suspension ....127 Wheels and tires......129 Fuel and lubricants ..... 130 Electrical system ......132 Dimensions and weights .... 134 Riding specifications ....135 Technical data...
Page 130: Threaded Fasteners
Threaded fasteners Tightening Activity Type of threaded fastener torque Front wheel ® Mudguard Internal TORX T25 (1) hand-tight ® Suspension cover Internal TORX T25 (1) hand-tight ® Brake caliper Internal TORX 30 Nm ® Axle clamping screw Internal TORX 19 Nm Quick-release axle Allen screw 22 50 Nm...
Page 131 Threaded fasteners Tightening Activity Type of threaded fastener torque Battery ® Battery compartment lid Internal TORX T25 (1) hand-tight Battery-terminal clamps External hexagon 10 or hand-tight slotted head screw, large (1) ® Securing bracket Internal TORX hand-tight Splash guard Splash guard Phillips screw, large (1) hand-tight (1) in the toolkit...
Page 132: Tire Pressures
Tire pressures Tire pressure measured when tires are cold. Accessories and loads Front Rear One-up 36.3 psi (2.5 bar) 42 psi (2.9 bar) One-up with luggage 36.3 psi (2.5 bar) 42 psi (2.9 bar) Two-up (with luggage) 36.3 psi (2.5 bar) 42 psi (2.9 bar)
Page 133: Engine
Engine Engine Type 4-cylinder inline engine, fitted crossways, inclined 55 Displacement 1,157 cc Bore/stroke 3.1/2.3 in (79/59 mm) Compression ratio 13.0 : 1 Power output Maximum rated output 120 kW - at engine speed 10,250 rpm Torque Max. torque - at engine speed 8,250 rpm Engine speeds Engine speed, maximum...
Page 134: Power Transmission
Power transmission Clutch Type Hydraulic multi-disk wet clutch Transmission Type 6-speed transmission Overall ratios 1st gear = 2.524 2nd gear = 1.842 3rd gear = 1.455 4th gear = 1.287 5th gear = 1.143 6th gear = 1.015 Rear-wheel drive Transmission from transmission to rear wheel Universal shaft with integrated torsional drive...
Page 135: Frame And Suspension
One fixed brake disk with 2-piston floating caliper Brake pads Organic Front suspension Type BMW Duolever Steering lock angle 2 x 30.3 Front wheel castor in normal-load position 4 in (101 mm) Rear suspension Type BMW EVO Paralever swinging arm...
Page 136: Frame And Suspension
Frame and suspension Front suspension system Type Central suspension strut with single-tube emulsion shock absorber Spring travel (bump) 2.36 in (60 mm) Spring travel (rebound) 2.17 in (55 mm) Total suspension travel 4.53 in (115 mm) Rear suspension system Type Central suspension strut with single-tube gas pressure shock absorber Spring preload and rebound-stage damping...
Page 137: Wheels And Tires
Wheels and tires Front wheel Type MTH2 angled rim shoulder with double tire retaining hump Rim size 3.50 x 17“ Tire size 120/70-ZR17 Rear wheel Type MTH2 angled rim shoulder with double tire retaining hump Rim size 5.50 x 17“ (OE: 6.00 x 17“) Tire size 180/55-ZR17 (OE: 190/50-ZR17)
Page 138: Fuel And Lubricants
When using special motorcycle oils, ensure suitability for wet clutches. Oil additives may not be used. Only synthetic engine oils approved for this motorcycle by BMW Motorrad may be used. Capacity with filter change 3.7 quarts (3.5 l) Top-up volume between MIN and MAX 0.53 quart (0.5 l)
Page 139 Fuel Fuel grade Premium grade unleaded fuel, minimum octane content 98 ((RON + MON) / 2) Capacity of fuel tank 5 gal (19 l) Reserve volume 1 gal (4 l) Brakes Brake fluid DOT 4 We recommend BMW brake fluid...
Page 140: Electrical System
Electrical system Battery Type Maintenace-free AGM battery Capacity 12 V 14 Ah Spark plugs Spark plugs BOSCH YR5DDE Fuses All circuits are electronically protected, so plug-in fuses are not necessary. If an electronic fuse trips and de-energizes a circuit, the circuit is active as soon as the ignition is switched on after the fault has been rectified.
Page 141 Electrical system Bulbs High-beam headlight H7 halogen bulb 12 V 55 W Low-beam headlight H7 halogen bulb 12 V 55 W Side lights 12 V 5 W Brake/rear light 12 V 21/5 W Turn indicators 12 V 10 W Power socket Ratings 12 V 5 A...
Page 142: Dimensions And Weights
Dimensions and weights Dimensions Maximum length (luggage rack) 87.7 in (2,228 mm) Maximum width (across mirrors) 33.7 in (856 mm) Maximum width (across mirrors) 48.4 in (1,230 mm) Seat height 32 in (820 mm) Height of seat (low seat 31.1 in (790 mm) Wheelbase in normal-load position 62.2 in (1,580 mm) Ground clearance in normal-load position...
Page 143: Riding Specifications
Riding specifications Speed Top speed over 125 mph (200 km/h) Acceleration 0-100 km/h 2.9 s Noises Riding noise to EU specification 80 dB (A) Stationary noise to EU specification 94 dB (A) at 5,125 rpm...
Page 145: Service
BMW Motorrad Service ..... 144 Confirmation of maintenance work ..........148 Confirmations of service ... 152 Service...
Page 146: Bmw Motorrad Service
To ensure that your BMW is lems. By having the necessary always in optimum condition, repairs done properly and in Important country-specific...
Page 147 50,000 km, 70,000 km, etc.) if BMW Running-in Check alone, you have the best pos- this distance is covered within The BMW running-in check sible access to approximately a year. has to be performed when the 200 authorized BMW motorcy-...
Page 148 Your authorized BMW motorcycle retailer will be happy to supply a copy of the current mainte- nance schedule for your motorcycle on request.
Page 149 BMW Running-In Pre-delivery Check Check Carried out in accordance with manufacturer’s instructions Carried out in accordance with manufacturer’s instructions Odometer reading Brake fluid changed: BMW Integral ABS Wheel circuit Control circuit Date, stamp, signature Date, stamp, signature...
Page 150: Confirmation Of Maintenance Work
Confirmation of maintenance work BMW Service BMW Service BMW Service BMW Annual Inspection BMW Annual Inspection BMW Annual Inspection BMW Service BMW Service BMW Service BMW Inspection BMW Inspection BMW Inspection Carried out in accordance with Carried out in accordance with Carried out in accordance with manufacturer’s instructions...
Page 151 Confirmation of maintenance work BMW Service BMW Service BMW Service BMW Annual Inspection BMW Annual Inspection BMW Annual Inspection BMW Service BMW Service BMW Service BMW Inspection BMW Inspection BMW Inspection Carried out in accordance with Carried out in accordance with Carried out in accordance with manufacturer’s instructions...
Page 152 Confirmation of maintenance work BMW Service BMW Service BMW Service BMW Annual Inspection BMW Annual Inspection BMW Annual Inspection BMW Service BMW Service BMW Service BMW Inspection BMW Inspection BMW Inspection Carried out in accordance with Carried out in accordance with Carried out in accordance with manufacturer’s instructions...
Page 153 Confirmation of maintenance work BMW Service BMW Service BMW Service BMW Annual Inspection BMW Annual Inspection BMW Annual Inspection BMW Service BMW Service BMW Service BMW Inspection BMW Inspection BMW Inspection Carried out in accordance with Carried out in accordance with Carried out in accordance with manufacturer’s instructions...
Page 154: Confirmations Of Service
Confirmations of service The list is intended as a record of maintenance, warranty and repair work, the installation of optional accessories and, if appropriate, special campaign (recall) work. Record of all work carried out in workshop Odometer Work details reading Date...
Page 155 Confirmations of service Record of all work carried out in workshop Odometer Work details reading Date...
Page 156 Confirmations of service Instrument cluster Instrument cluster Instrument cluster replaced replaced replaced at distance at distance at distance _______________________ _______________________ _______________________ (odometer reading) (odometer reading) (odometer reading) ________________________ ________________________ ________________________ Date, stamp, signature Date, stamp, signature Date, stamp, signature...
Page 157: Index
Replacing bulb, 113 Warning light, 20 Technical data, 138 Brake pads, 64 Accessories Warning indicator for charge Brakes BMW optional equipment, 4 current, 26 Brake pads, 93 Cable routing, 81 BMW Service Checking front brake pad General instructions, 80 Annual inspection, 145...
Page 158 Center stand Care Electronic engine-management Extending, 71 Care products, 122 system Retracting, 73 Chrome, 123 Tampering with control unit, 55 Checklist, 56 Paint, 123 Electronic immobilizer Clock Plastics, 123 Display, 24 Display, 20 Protective wax coating, 124 Explanations, 35 Setting, 16, 40 Radiator, 123 Emergency ON/OFF Clutch...
Page 159 General view, Ignition Adjusting shock absorbers, 49 left side, 9 Switching off, 34 Adjusting the spring Grip heating, 15, 39 Switching on, 34, 57 preload, 50 Indicator lights, 16, 20 Calling up settings, 49 Handlebar fitting Inflation pressures, 130 Explanations, 49 Left, 14 Instrument cluster, 16 Operation, 14...
Page 160 Rider’s equipment, 6 Spark plugs, technical data, 138 Motorcycle equipment, 5 Running in Speed Multifunction display, 16 Brake pads, 64 Safety information, 54 General information, 63 Technical data, 141 Speedometer, 16 Neutral, indicator light, 20 Splash guard, 120 Safety check before a Starter, 15 journey, 56 Operating range, 38...
Page 161 Tightening torques, 128 Warning lights, 16, 20 Toolkit, 89 Warnings, 4 Transmission Wheels Gear shifts, 64 Checking rims, 98 Position on starting, 57 Checking tire pressure, 51 Technical data, 132 Checking tread depth, 98 Tripmaster, 14, 20, 37 Installing front wheel, 101 Turn indicator Installing rear wheel, 104 Left, 14...
Page 162 Vehicle/dealership data Vehicle data Dealership data Model Contacts in Service Department Vehicle identification number Ms./Mr. Color code Phone number First registration Registration number Dealership address/phone (company stamp)
Page 163 Errors and omissions the accessories fitted or the excepted. national-market specification. © 2004 BMW Motorrad Not to be reproduced either No claims will be entertained as a result of such discrepan- wholly or in part without written cies.
Page 164 BMW recommends Castrol The most important data for a filling station stop can be found in the following chart: Fuel Grade Premium grade unleaded fuel Fuel tank capacity 5 gal (19 l) Tire pressures Front Rear One-up 36.3 psi (2.50 bar) 42 psi (2.90 bar)
Page 165 Please attach this sticker to the inside back cover page of your Rider’s Manual Reporting Safety Defects individual problems between you, your dealer, or BMW of North If you believe that your vehicle has America, LCC. a defect which could cause a crash...
Page 166 Information on BMW Motorrad Integral ABS How does ABS work? resulting in a danger of falling. ensure driving stability when The maximum braking force Before this situation occurs, contact with the road surface which can be transferred to the ABS intervenes and is restored.
Page 167 ON/OFF During driving-safety training Field observations by BMW switch, the light and all elec- courses an unusually high Motorrad show that no com- tronic systems remain...
Page 168 This optimally utilizes the rider to brake the motor- A fault in the BMW Motorrad the dynamic load increase on cycle. Integral ABS is indicated by a the front wheel. At the same...
Page 169 • Always brake with the front How important is regular How is the BMW Motorrad maintenance? Integral ABS designed? and rear brakes Any technical system is The BMW Motorrad Integral • In clear situations, carry out always only as good as...

BMW K 1200 R Rider's Manual

1 Overview

2 Status Indicators

3 Operation

4 Riding

5 Accessories

6 Maintenance

7 Care

8 Technical Data

9 Service

Index

Quick Links

Related Manuals for BMW K 1200 R

Summary of Contents for BMW K 1200 R

Table of Contents