Cisco Explorer 8540HD Quick Reference Manual

Notice to Installers
The servicing instructions in this notice are for use by qualifi ed service personnel only. To reduce risk of electric shock, do not perform any servicing other than that contained in
the operating instructions, unless you are qualifi ed to do so.
Note to System Installer
For this apparatus, the coaxial cable shield/screen shall be grounded as close as
practical to the point of entry of the cable into the building.For products sold in the
US and Canada, this reminder is provided to call the system installer's attention to
Article 820-93 and Article 820-100 of the NEC (or Canadian Electrical Code Part 1),
which provides guidelines for proper grounding of the coaxial cable shield.
This symbol is intended to alert you that uninsulated voltage within this product
may have sufficient magnitude to cause electric shock.Therefore, it is dangerous
to make any kind of contact with any inside part of this product.
Ce symbole a pour but d'alerter toute personne qu'un contact avec une pièce
interne de ce produit, sous tension et non isolée, pourrait être suffisant pour
provoquer un choc électrique. Il est donc dangereux d'être en contact avec toute
pièce interne de ce produit.
IMPORTANT SAFETY INSTRUCTIONS
Read These Instructions
Keep These Instructions
Heed All Warnings
Follow All Instructions
Power Source Warning
A label on this product indicates the correct power source for this product. Operate this product only from an elec-
trical outlet with the voltage and frequency indicated on the product label. If you are uncertain of the type of power
supply to your home or business, consult your service provider or your local power company.
The AC inlet on the unit must remain accessible and operable at all times.
Ground the Product
WARNING: Avoid electric shock and fi re hazard! Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.
If this product connects to coaxial cable wiring, be sure the cable system is grounded (earthed). Grounding provides
some protection against voltage surges and built-up static charges.
Outdoor Grounding System
If this product connects to an outdoor antenna or cable system, be sure the antenna or cable system is grounded
(earthed). This provides some protection against voltage surges and built-up static charges.
Article 810 of the National Electric Code (NEC) ANSI/NFPA No. 70-1990, provides the following information:
• Grounding of the mast and supporting structure
• Grounding the lead-in wire to an antenna discharge unit
• Size of the grounding conductors
• Location of the antenna-discharge unit
• Connection to grounding electrodes
• Requirements for the grounding electrodes (see the following antenna grounding diagram as recommended by
NEC ANSI/NFPA 70)
WARNING: Avoid electric shock and fi re hazard! Do not locate an outside antenna system in
the vicinity of overhead power lines or power circuits. Touching power lines or circuits might be fatal.
Protect the Product from Lightning
For added protection, unplug this apparatus during lightning storms or when unused for long periods of time. In
addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.
Antenna Lead In Wire
Ground Clamps
Antenna Discharge Unit
(NEC Section 810-21)
Grounding Conductors
Electric Service (NEC Section 810-20)
Equipment
Ground Clamps
NEC = National Electrical Code 1990 Power Service Grounding Electrode System
National Fire Protection Association (NEC Art 250, Part H)
TO CATV INSTALLER
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National Electrical
Code (NEC) that provides guidelines for proper grounding, and in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close to the point of entry as practical.
CAUTION: To reduce the risk of electric shock, do not remove cover (or back).
No user-serviceable parts inside. Refer servicing to qualified service personnel.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
This symbol is intended to alert you of the presence of important operating and
maintenance (servicing) instructions in the literature accompanying this product.
Ce symbole a pour but de vous avertir qu'une documentation importante sur le
fonctionnement et l'entretien accompagne ce produit.
20070131 SysInstaller 820 US/Canada/Intl
Verify the Power Source from the On/Off Power Light
When the on/off power light is not illuminated, the apparatus may still be connected to the power source. The light
goes out when the apparatus is turned off , regardless of whether it is still plugged into an AC power source.
Eliminate AC Power/Mains Overloads
WARNING: Avoid electric shock and fi re hazard! Do not overload AC power/mains, outlets,
extension cords, or integral convenience receptacles. For products that require battery power or other
power sources to operate them, refer to the operating instructions for those products.
Prevent Power Cord Damage
Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the
point where the cord exits from the apparatus.
Provide Ventilation and Select a Location
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not place this apparatus on a bed, sofa, rug, or similar surface.
• Do not place this apparatus on an unstable surface.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifi ers) that produce heat.
• Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation provides proper
ventilation.
• Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or other objects
on top of this product.
Operating Environment
The set-top is designed for operation indoors with a temperature range from 32° to 104° F (0° to 40°C). Each set-
top should have adequate spacing on all sides so that the cooling air vents on the chassis are not blocked.
Protect from Exposure to Moisture and Foreign Objects
Do not use this apparatus near water.
WARNING: Avoid electric shock and fi re hazard! Do not expose this product to liquids, rain, or
moisture.
WARNING: Avoid electric shock and fi re hazard! Unplug this product before cleaning. Clean
only with a dry cloth. Do not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static
cleaning device (dust remover) to clean this product.
WARNING: Avoid electric shock and fi re hazard! Never push objects through the openings in
this product. Foreign objects can cause electrical shorts that can result in electric shock or fi re.
Accessories Warning
WARNING: Avoid electric shock and fi re hazard! Only use attachments/accessories specifi ed
by your service provider or the manufacturer.
Service Warnings
WARNING: Avoid electric shock! Do not open the cover of this product. Opening or removing
the cover may expose you to dangerous voltages. If you open the cover, your warranty will be void. This
product contains no user-serviceable parts. Refer all servicing to qualifi ed service personnel.
Servicing is required when the apparatus has been damaged in any way, such as a power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Explorer 8540HD and 8550HD DVR
CH+
VOL- VOL+
POWER SELECT
CH-
Check Product Safety
Upon completion of any service or repairs to this product, the service technician must perform safety checks to
determine that this product is in proper operating condition.
Protect the Product when Moving It
Always disconnect the power source when moving the apparatus or connecting or disconnecting cables.
WARNING: Avoid personal injury and damage to this product! Use only with the cart, stand,
tripod, bracket, or table specifi ed by the manufacturer or sold with the apparatus. When
a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from
tip-over.
20070320 Set-Top Cable US & Canada
FCC Compliance
United States FCC Compliance
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in
accordance with the instructions, it may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna, if applicable.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected.
• Consult the cable company or an experienced radio/television technician for help.
Any changes or modifi cations not expressly approved by Scientifi c-Atlanta, Inc., could void the user's authority to
operate the equipment.
The information shown in the FCC Declaration of Conformity paragraph below is a requirement of the FCC and is
intended to supply you with information regarding the FCC approval of this device. The phone numbers listed are for
FCC-related questions only and not intended for questions regarding the connection or operation for this device. Please
contact your cable service provider for any questions you may have regarding the operation or installation of this device.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) the device
may not cause harmful interference, and 2) the device must accept any interference received, including interference
that may cause undesired operation.
Explorer 8540HD and 8550HD Digital Video Recorders
Model: 8540HD and 8550HD
Manufactured by: Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 678 277-1120
Quick Reference Guide
EXPLORER ® 8550HD
GUIDE INFO EXIT LIST
L AUDIO IN R VIDEO IN
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.
Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions that may appear in this guide. We reserve the
right to change this guide at any time without notice.
AVC VIDEO LICENSE
With respect to each AVC/H.264 product, we are obligated to provide the following notice:
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF
A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN
COMPLIANCE WITH THE AVC STANDARD ("AVC VIDEO") AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED
BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM.
Accordingly, please be advised that service providers, content providers, and broadcasters may be required to
obtain a separate use license from MPEG LA prior to any use of AVC/H.264 encoders and/or decoders.
Cisco Systems, Inc.
5030 Sugarloaf Parkway, Box 465447
Lawrenceville, GA 30042
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affi liates in the U.S. and other countries.
To view a list of Cisco's trademarks, go to this URL: www.cisco.com/go/trademarks.
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
HDMI, the HDMI logo, and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
Other third party trademarks mentioned are the property of their respective owners.
The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)
©2007, 2010, 2012 Cisco Systems, Inc. All rights reserved.
October 2012 Printed in United States of America
™
20081121 FCC Standard
678 277-1120
800 722-2009
www.cisco.com
Part Number 78-4022346-01 Rev D