Items Needed - THUNDER TIGER Tiger Trainer MKIII Assembly Instruction Manual

INTRODUCTION
Introduction
All of us at Thunder Tiger want to thank you for choosing the best looking, easiest
building and best flying ARF trainer available the Tiger Trainer 40.The kit features state-
of-the-art engineering that provides quick and easy assemble of a strong, yet lightweight
airplane that will give you an enjoyable and educational experience.
To gain the most from this airplane kit, it is important that you read the instructions
thoroughly and then follow them exactly. This instruction manual has been written with a
novice modelers in mind, but includes many hints and modeling tips that even
experienced modeler can benefit from. We strongly suggest that you read through the
construction sequence and eliminate many questions you might have if you did not read
the manual prior to starting the actual construction.
The first thing you should do before beginning assembly is to check the contents of your
kit against the parts list on pages 4 and 5. If any parts are missing, contact your dealer or
authorised Thunder Tiger Distributors immediately for replacement.
TABLE OF CONTENTS
INTRODUCTION...........................................................................................2
OTHER ITEMS REQUIRED............................................................................2
ITEMS NEED CHECK LIST.............................................................................3
PARTS LIST...............................................................................................4-5
PRE-ASSEMBLE NOTES...............................................................................6
WING.........................................................................................................6-8
FUSELAGE...................................................................................................8
INSTALL THE ENGINE................................................................................8-9
INSTALL FUEL TANK...................................................................................10
TAIL.......................................................................................................10-12
INSTALL THE RADIO..............................................................................12-13
BALANCE & FINAL ASSEMBLY FLIGHT..................................................14-16
OTHER ITEMS REQUIRED FOR
ASSEMBLY
A checklist is also provided on the next page which
will make shopping for these items easier.
Radio - A 4- channel radio with 4 standard servos is
required. Most lower priced 4-channel radios only
come with three standard servos so you may need to
purchase the fourth servo separately.
Tiger Trainer
ACCESSORIES
No.1263-65
Carry Master-Thunder
Tiger offer a complete
organizer of field
equipment. All you
need is included.
No.2674
12V DC Starter- Provides high
torque starting power to start
your outboard engine.
No.2624
Sealed Battery- 7Ah 12V
Sealed Battery.
2
MK
Adhesives- You will need two types of adhesives for the
Tiger Trainer - Epoxy and
adhesives. We recommend that you purchase both 5-
minute and 30-minute epoxy to cut down on assembly
time, but you can get by with only 30-minute epoxy if time
is no important. You will also need a small bottle of both
"Thick" and "Thin" instant adhesive.
Tools-Model assembly can be much easier if the proper
tools are used. Therefore we have included in our
checklist to above, a complete listing of all the tools we
used to assemble our prototype models. As you will
notice, many household tools can be utilized during
construction.
No.9041
No.9800
Engine The Thunder Tiger GP-42 and F-54S are the ideal
engines for this airplane. These quiet running engines are
easy to start, require no special break in periods, are very
easy to maintain and will last for years.
Instant ( cyanoacrylate )
Flight Equipment
that you will need to purchase in order to get your engine
running and your plane in the air. These are listed at the
bottom.
Flight Equipment Needed Check List
Foam Rubber Padding for the radio
Stick on Lead Strip for balancing the plane
3 or 4 Props (see engine instructions)
10%-15% Glow Fuel
Fuel Pump or Bulb
Electric Starter or " Chicken Stick"
Glow starter
Extra Glow Plug(s)
Silicon Tubing
Comprehensive Items Needed Check List
4-Channel Radio with 4 Standard Servos
5-Minute Epoxy (4 ounces or so)
30-Minute Epoxy (4 ounces or so)
"Thin" Instant Adhesive (1/2 ounce)
"Thick" Instant Adhesive (1/2 ounce)
Hobby Knife and Blades
Epoxy Mixing Sticks and/or Brushes
Sandpaper (150 grit)
Masking Tape
Rubbing Alcohol
Paper Towels
Ruler
90 Degree Triangle
Waxed Paper
Fine-Point, Felt-Tip Pen
Misc. Household Tools
Drill and Bits (1/16", 5/64", 3/32")
3

ITEMS NEEDED

There are several "support" items