Page 1
Thank you for purchasing the DLP Projector. Please read this user’s guide to ensure correct use of the device. Save this user’s guide for future reference. OUTLINE This DLP Projector can display various computer signals and NTSC/PAL/SECAM video signals. FEATURES 1. High Brightness 2.
ATE YOUR PROJECTOR. SAVE THIS USER’S GUIDE FOR FUTURE REF- ERENCE . Safety Instructions Read this user’s guide before you operate your projector and save it for future reference. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
• Do not touch the ventilation grill when the projector is under operation. Save this user’s guide: The information contained in this manual will assist you in operating and maintaining your personal projector. FCC Statement FCC STATEMENT - CLASS A: This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
Shipping Contents The Projector is shipped with the cables required for connection to standard PC or laptop computers. Carefully unpack and verify that you have all the items shown below. If any of these items are missing, please contact personnel at the place of purchase.
IR remote sensor Ventilation grill Speaker Projection lens adjuster Computer signal input Computer signal output connector DLP Personal Projector 10 11 14 15 Audio/ Video connector Computer Audio IN USB mouse connector S-Video jack RS-232C control port Rear adjuster feet...
External Control Panel Power Presses the Power key to turn the projector on or off. Auto Automatically determines the best picture settings for current received signals. Left/ Keystone - Right/ Keystone + Menu will display the menu system on screen. Press Menu again to access the sub-menus.
Adjuster The projector is equipped with 2 quick-release adjuster feet. Push the buttons to adjust its tilt angle. Lift the projector up and press the adjuster button to release the adjuster. The adjuster will drop into position and be locked.
Remote Control Description The remote control sensors are located in the front/ back of the projector. The distance between the sensor and the remote control should not exceed 6 meters. Power Menu 3 Left/ Keystone - 4 Right/ Keystone +...
Dispose of used batteries accord- ing to the manufacturer’s instructions. Install batteries as indicated by the diagram inside the compartment. DLP Personal Projector Position the lid over the compartment and snap it back into place.
INSTALLATION Screen Size Place the projector at the required distance from the screen according to the desired picture size (see the table below). Screen Size (Max.) Diagonal A. Width (in) (cm) 30.4 61.8 60.8 123.7 91.2 185.3 121.5 247.0 151.9 308.7...
Page 14
Please refer to "Menu System" on page 13 for information on the HDTV OSD selections. Connecting to Various Equipment It only takes a few seconds to connect your projector to your desktop or notebook computer, VCR, or other systems. However, a Mac adapter (an optional accessory) is needed for connection to Macintosh computers.
Press POWER to start the unit. The back-lit POWER key flashes green and stays green when the power is turned on. (When the power is turned off, there is a 120-second cooling period before the projector can be re-started.) Switch on all connected equipment. Remote Control...
In some cases, you may need to optimize the picture quality. To do this, press the AUTO key on the control panel of the projector or on the remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust settings to provide the best picture quality.
Source Selection When several input sources are available, press the SOURCE key to make a selection from the control panel of the projector or the remote control. Projector Auto Menu System Press Menu for the main menu, and then press Press Menu again to select items in the sub-menu.
Increases or decreases the color range (R, G, B) of the image. Color *This function is not available when the input mode is PC. Adjusts the image to make it appear more red or blue. Tint *This function is not available when the input mode is PC. DLP Personal Projector...
*This function is not available when the input mode is PC. Adjusts the image to make it appear more red or blue. Tint *This function is not available when the input mode is PC. DESCRIPTION 2. 16:9 DLP Personal Projector...
3. Rear screen projection 4. Ceiling mounted and rear- screen projection Selects the input source from among PC, YP Video and S- Source Video. Adjusts the volume level. Volume Adjusts the treble level. Treble Adjusts the bass level. Bass Mute DLP Personal Projector...
User logo Enables the user to define the logo screen that will dis- play during strat-up. Three modes are available: Default (LG logo), black screen and blue screen. Returns all settings to their factory preset values. Default Selects video mode.
Increases or decreases the color range (R, G, B) of the image. Adjusts the image to make it appear more red or blue. Adjusts the image to make it appear sharper or softer Selects PIP image systems: NTSC, PAL, SECAM DLP Personal Projector...
Please do not unplug the power cord before POWER is shut down or during the two-minute cooling process. • If the projector is not properly shut down, to protect the lamp, the sys- tem will detect this and cool the lamp for two minutes automatically before turning on again.
Lamp Replacement Please check with LG service center for the information of lamp replacement. When the LED lights up red, it is warning you that lamp uage has exceeded 1500 hours. Replace the projection lamp with a new one immediately.
Caution To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp. To reduce the risk of injuries to fingers and damage to internal compo- nents, use caution when removing lamp glass that has shattered into sharp pieces.
Select the correct video system. Adjust brightness, contrast, or saturation. Press Auto on the control panel of the projector or the remote control unit to get better picture quality. Adjust the focus. Reposition the unit to improve its projection angle.
20 hours. The lamp has been in operation for over 1500 hours. The warning message will display for 30 sec- onds every 5 minutes after you turn on the projector and the power will turn off automatically after 10 minutes.
0°C ~ 40°C 7 lbs (3.2 Kg) D-sub 15-pin (female) Mini DIN 4-pin port x1 RCA jack x1 RCA jack x3 Mini jack stero port RCA jack L, R x2 A/B series x1 3 watt x 1 9-pin x1 DLP Personal Projector...
31.5 37.9 31.5 37.9 31.5 37.9 35.0 43.3 35.2 37.9 48.1 46.9 53.7 49.7 48.4 56.5 60.0 68.7 64.0 DLP Personal Projector Remark 70.1 85.1 VESA 70.0 85.1 VESA 60.0 VESA 72.8 VESA 66.7 Macintosh 85.0 VESA 56.3 VESA 60.3 VESA 72.2...