Table of Contents
Advertisement
SAVE THIS BOOK
This book is valuable. In addition to instructing you on
how to install and maintain your appliance, it also
contains information that will enable you to obtain
replacement parts or accessory items when needed.
Keep it with your other important papers.
WARNING: Always leave glass doors fully opened or fully closed when operating this fireplace.
ALL DIMENSIONS IN THIS MANUAL ARE IN
INCHES UNLESS OTHERWISE SPECIFIED
DESA
2701 INDUSTRIAL DRIVE
P.O. BOX 90024
BOWLING GREEN, KY 42101-9004
www.desatech.com
INSTALLATION INSTRUCTIONS
This fireplace is approved for use as a wood burning fireplace or for
use with a vented gas log approved to ANS Z21.60, Z21.84 or RGA
2-72 standards or for use with a vent-free gas log heater approved to
ANS Z21.11.2 standard. A DESA hood must be installed when
using a vent-free gas log heater (see Accessories, p. 12).
ICBO # ER-3507
OMNI Test Laboratories
(V)B36
(V)B36I
36" smooth face with insulation
(V)B36L, CWB36C
(V)B36LI
36" circulating with insulation
36" smooth face
36" circulating
P/N 109034-01
REV E
9/03
Advertisement
Table of Contents
Related Manuals for Desa B36
Summary of Contents for Desa B36
-
Page 1: Installation Instructions
2-72 standards or for use with a vent-free gas log heater approved to contains information that will enable you to obtain ANS Z21.11.2 standard. A DESA hood must be installed when replacement parts or accessory items when needed. using a vent-free gas log heater (see Accessories, p. 12). -
Page 2: Table Of Contents
CONTENTS INTRODUCTION ------------------------------------------------------------- PG. 2 SELECTING LOCATION ------------------------------------------------------------- PG. 2 MINIMUM CLEARANCES ------------------------------------------------------------- PG. 2 FRAMING AND INSTALLING ------------------------------------------------------------- PG. 3 HEARTH EXTENSION ------------------------------------------------------------- PG. 3 OUTSIDE AIR KIT INSTALLATION ------------------------------------------------------------- PG. 3 FAN/BLOWER KIT ASSEMBLY ------------------------------------------------------------- PG. 4 CHIMNEY PIPE AND OFFSET INSTALLATION ------------------------------------------------------------- PG. -
Page 3: Introduction
Back and side of fireplace -------------- ¾” minimum designed and tested for the fireplace system, you may Note: The ¾” clearance is not required at the nailing flanges cause a fire hazard. ♦ The DESA warranty will be voided by and DESA • Floor* ------------------------------------- 0” minimum disclaims any responsibility for the following actions: *See step 2 of “Installing the Fireplace”... -
Page 4: Framing And Installing
FRAMING AND INSTALLING THE FIREPLACE HEARTH EXTENSION A hearth extension projecting a minimum of 16” in front of STEP 1: Frame the opening for the fireplace using the and a minimum of 8” beyond each side of the fireplace dimensions shown in figures 1 & 2. opening is required to protect combustible floor construction STEP 2: If the fireplace is to be installed directly on carpeting, in front of the fireplace. -
Page 5: Fan/Blower Kit Assembly
Chimney weight above offset rests on return elbow. CHIMNEY PIPE Straps must be securely nailed to rafters or joists (see figure 8, The DESA chimney system consists of 12, 18, 24, 36 and 48 details a & b). inch, snap-lock double-wall pipe segments, planned for Maximum length of pipe between supports (return elbow maximum adaptability to individual site requirements. -
Page 6: Firestop Spacers
All pipe connections between the offset and return must be secured with two screws, only on the outer Figure 7 *TYPICAL OFFSET INSTALLATION pipe, and shall not penetrate the inner stainless. Figure 9 ELBOW OFFSET *For systems with two elbow sets, the minimum height is 22 feet. -
Page 7: Flashing And Termination
PENETRATING THE ROOF INSTALLING FLASHING ON A METAL ROOF To maintain a 1-inch clearance to the pipe on a roof with a When installing the flashing on a metal roof, it is required that pitch, a rectangular opening must be cut. putty tape be used between the flashing and the roof. -
Page 8: Finishing Your Fireplace
TERMINATIONS / SPARK ARRESTOR The fireplace system must be terminated with the listed round top or chase terminations. In any case, refer to the installation instructions supplied with the termination. The terminations approved for this fireplace are the RT-8DM and RTL-8DM that can be used for flashing or chase and ET-8DM, ETO- 8DM, ETL-8DM and ETLO-8DM for chase style termination only. -
Page 9: Mantels
MANTELS OPERATING GUIDELINES AND MAINTENANCE INSTRUCTIONS A mantel may be installed if desired (see figure 18), GLASS DOORS woodwork such as wood trims, mantels, or any other Glass doors are optional with the fireplace. When the combustible material projecting from the front face must not fireplace is in operation, doors must in FULLY OPENED or be placed within 9 inches of the fireplace opening. -
Page 10: Gas Line Installations
Remove fragmented portions of refractory (see figure 21). NOTE: A DESA hood must be installed when using an unvented gas log set (see accessories on page 12). WARNING: Do not operate an unvented gas log set in this fireplace with the chimney removed. -
Page 11: Damper Operation
(see figure 24). Figure 24 DAMPER ROD WARNING: Risk of fire! Replace grate with DESA model 107001-01 grate only. This grate has been designed to keep the operation of your fireplace safe and efficient. -
Page 12: Illustrated Parts
107128-01 CONDUIT, GAS 27253 NOTICE: INDENTATION 106953-01 BOTTOM, WRAPPER 110037-01 ELECTRICAL DUCT ASSEMBLY 106943-01 WRAPPER, FIREBOX 54199 LABEL-REMOVE GAS KNOCKOUT * ITEMS NOT SHOWN FOR CLARITY **FOR MODELS (V)B36L, (V)B36LI, CWB36C ***FOR MODELS (V)B36, (V)B36I For more information, visit www.desatech.com... - Page 13 ILLUSTRATED PARTS For more information, visit www.desatech.com...
-
Page 14: Replacement Parts
REPLACEMENT PARTS ACCESSORY PARTS For more information, visit www.desatech.com...