Remote Arming And Disarming; Emergency Keys; When Alarm Sounds; Intrusion (Burglary) Alarm Continuous Siren - DSC Alexor User Manual

Remote Arming and Disarming

The system can be armed and/or disarmed, if programmed by the installer, using a remote control
device (wireless key fob). When arming the system using the Arm button on a wireless key, the sys-
tem will acknowledge the command by sounding a single bell/siren squawk, if programmed to do
so by the installer. When disarming using the disarm button on a wireless key, the system will
acknowledge the command by sounding two bell/siren squawks. Three squawks, when disarming
with the disarm button, indicates that an alarm occurred while the system was armed. If you are
unsure of the cause of the alarm, proceed with caution (see section on 2-way Wireless Keys).

Emergency Keys

Fire
Press the (
Auxiliary, or Panic alarm. The keypad buzzer will beep indicating that the alarm input has been
accepted and transmission to the central station is underway. The
sound the siren depending on installer setup.
NOTE: The Fire button can be disabled by the installer.
NOTE: The Auxiliary Alarm button is not intended to be used for medical signals.

When Alarm Sounds

The system can generate 3 different alarm sounds:
• Continuous Siren = Intrusion/Burglary Alarm
• Temporal / Pulsed Siren = Fire Alarm
• 4 beeps, 5-second pause, 4 beeps = Carbon Monoxide alarm
NOTE: The priority of signals is fire alarm, carbon monoxide alarm then burglary alarm.

Intrusion (Burglary) Alarm Continuous Siren

If you are unsure of the source of the alarm, proceed with caution! If the alarm was accidental,
enter your access code or present your prox tag to silence the alarm. If the alarm system is dis-
armed within the programmed Abort Window (check with the installer if this option has been en-
abled on your system and what is the transmitter delay time programmed), no alarm transmission
to the Central Station will occur. Following the Abort Window there appears a 5-minute Cancel
Window, during which a user can cancel, by entering their access code or presenting their prox
tag, an alarm that has been previously transmitted. A cancel signal will be transmitted to the cen-
tral station and the alarm system will also announce that the cancel signal was transmitted. Call
your central station to avoid a dispatch.

Fire Alarm Pulsed Siren

Follow your emergency evacuation plan immediately!
If the fire alarm was accidental (burned toast, bathroom steam, etc.), enter your access code or
present your prox tag to silence the alarm. Call your central station to avoid a dispatch.

Carbon Monoxide Alarm

Activation of your CO alarm indicates the presence of carbon monoxide (CO), which can be
fatal. During an alarm, the red LED on the CO detector flashes rapidly and buzzer sounds with a
repeating cadence of: 4 quick beeps, 5-second pause, 4 quick beeps. If an alarm sounds:
1. Operate silence button.
2. Call emergency services or your fire department.
3. Immediately move outdoors or to an open door/window.
WARNING: Carefully review your Carbon Monoxide Installation/User Guide to determine the nec-
essary actions required to ensure your safety and ensure that the equipment is operating correctly.
Incorporate the steps outlined in the guide into your evacuation plan.
Time & Date Programming
HH:MM MM/DD/YY
09:06 01/31/09
programming. If you are viewing a 'Loss of Clock' trouble from within the trouble menu (
press to directly enter Date and Time programming (see Trouble Conditions).
,
NOTE: Your installer may have programmed your system to display the time and date while the
keypad is idle. Press the
Auxiliary
), ( ), or
Press
Functions. Use the
then press
(HH:MM), followed by the date (MM:DD:YY). Press
button to temporarily clear the date and time display if desired.
Panic
( ) button for 2 seconds to generate a Fire,
then your master access code to enter User
,
to select. Enter the time in 24-hr. format
,
4
button may or may not
buttons to find the menu option,
to exit
),
,