SATO CL4NX UHF Configuration Manual

UHF Inlay Configuration Guide
In order to successfully configure your CL4NX UHF printer,
you will need the following information about your label.
Feed direction will affect encoding.
This is signified using the inlay
images in the following table.
Region Manufacturer
Technology
Technology
Technology
CL4NX UHF Inlay Placement & Configuration Table
This recommendation has been tested successfully at SATO. Results may vary in the actual customer installation due to overall system tolerances. Validation of
functionality in the actual system is therefore recommended.
In no event shall SATO be liable for any faults arising out of use of or inability to use the product.
Placement and Configurations
globally valid with minor variation.
Valid for Frequencies that fall
within the FCC range, 902-928MHz
Inlay
Region Manufacturer
[IC Chip]
Alien ALN-9640 "Squiggle"
Technology [Alien Higgs3]
Alien ALN-9662 "Short"
Technology [Alien Higgs3]
Alien ALN-9762 "Short"
Technology [Alien Higgs4]
Alien ALN-9610 "Squig"
Technology [Alien Higgs3]
Alien ALN-9710 "Squig"
Technology [Alien Higgs4]
Alien ALN-9720 "HiScan"
Technology [Alien Higgs4]
Alien ALN-9654 "G Tag"
Technology [Alien Higgs3]
ALN-9728
Alien
"Garment Tag"
Technology
[Alien Higgs4]
ALN-9728-90
Alien
"Garment Tag"
Technology
[Alien Higgs4]
Alien ALN-9730 "Squiglette"
Technology [Alien Higgs 4]
Alien ALN-9630 "Squiglette"
Technology [Alien Higgs 3]
AZ-9762
Arizon
[Alien Higgs4]
Avery AD-110m5
Dennison [Impinj Monza5]
Inlay
Feed Direction
[IC Chip]
Alien ALN-9640 “Squiggle”
[Alien Higgs3]
Alien ALN-9662 “Short”
[Alien Higgs3]
Alien ALN-9762 “Short”
[Alien Higgs4]
Feed Direction
The arrow in the header of table
indicates the direction in which labels
are output from the printer.
Feed Direction
X: Liner Edge to Center of Chip
Y: Optimum Encoding Position*
S: Minimum Inlay Separation
*Y: Measured from tail edge of I-mark to lead edge of inlay when
I-mark sensor is used.
Measured from lead edge of label to edge of inlay when Gap
sensor is used.
Standard Antenna Position determined by value of Y.
When Antenna Pitch is "Short", Standard Antenna Position
can be set to any position; "Blue", "Yellow", or "Green".
(Y=) Standard Antenna Position
Position(mm) Power (dBm)
Antenna
X Y S Write Read
Pitch
47.5-57 3-5 21 24 14 Short
47.5-57 18-36 33 16 7 Standard
35-45 0-5 23 24 18 Short
35-65 10-24 50 24 16 Standard
50-60 0-5 20 24 13 Short
50-60 15-22 43 24 10 Standard
The value of "Y" will affect printer configuration of
Antenna Selection and Antenna Position.
Position(mm) Power (dBm)
X Y S Write Read
47.5-57 3-5 21 24 14
47.5-57 18-36 33 16
35-45 0-5 23 24 18
35-65 10-24 50 24 16
50-60 0-5 20 24 13
50-60 15-22 43 24 10
22.5-42 2-5 21 24 13
22.5-62 15-24 85 24 15
22.5-62 3-6 21 24 15
22.5-37 14-28 80 23 20
19.5-59 0-3 31 24 18
34.5-59 14-32 80 24 17
46.5-56.5 1-10 25 20 17
46.5-61.5 14-30 58 14 10
22.5-37.5 0-5 36 23 15
22.5-62.5 6-19 105 24 18
- - - -
15-35 24-37 85 18 10
- - - -
55 17-24 26 24 11
40-55 0-4 22 24 16
40-70 15-33 59 24 17
35-50 0-3 25 24 19
40-65 11-36 48 24 17
21.5-46.5 4-11 22 24 16
36.5-46.5 11-32 65 24 20
(mm)
Blue Yellow Green
- - -
18-23 24-29 30-36
- - -
10-14 15-20 21-24
- - -
15-18 19-22 -
(Y=) Standard Antenna Position
(mm)
Antenna
Blue Yellow
Pitch
Short - -
7 Standard 18-23 24-29
Short - -
Standard 10-14 15-20
Short - -
Standard 15-18 19-22
Short - -
Standard 15-18 19-24
Short - -
Standard 14-18 19-24
Short - -
Standard 14-17 18-24
Short - -
Standard 14-18 19-24
Short - -
Standard 6-9 10-14
- Short - -
Standard - 24-30
- Short - -
Standard 17-20 21-24
Short - -
Standard 15-23 24-28
Short - -
Standard 11-19 20-28
Short - -
Standard 11-17 18-25
First edition: Mar 2014 Q04502000
©2014 SATO CORPORATION
Green
-
30-36
-
21-24
-
-
-
-
-
25-28
-
25-32
-
25-30
-
15-19
-
31-37
-
-
-
29-33
-
29-36
-
26-32