Page 1
SX-WNT929 RC-ZAS04 • This Service Manual is the “Revision Publishing” and replaces “Simple Manual” of NSX-T929 (LH), (S/M Code No. 09-00C-440-2T1). • If requiring information about the CD mechanism, see Service Manual of 6ZG-1, (S/M Code No. 09-001-338-7N8). S/M Code No. 09-013-440-2R1...
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully CAUTION the instructions below when servicing. Use of controls or adjustments or performance of proce- dures other than those specified herin may result in WARNING!! hazardous radiation exposure.
NOTE ON BEFORE STARTING REPAIR 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed.
Page 5
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
ELECTRICAL MAIN PARTS LIST REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION MAIN C.B 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A12-317-080 C-CAP,U 0.1-50 Z F 8B-NF4-635-010 C-IC,LC876596W-5T96 87-A12-317-080 C-CAP,U 0.1-50 Z F 87-A21-831-010 IC,SPS-422-1-F1 87-A12-317-080 C-CAP,U 0.1-50 Z F 87-A20-355-010 IC,CXA1553P 87-A12-317-080 C-CAP,U 0.1-50 Z F...
TRANSISTOR ILLUSTRATION E C B E C B B C E G D S CDA1585BC CC5551 2SB1370 2SK3053 CSA952K 2SA1981Y 2SB1375 CSC4115BC 2SA1979O/Y 2SB1649 KTA1266GR 2SD2562 KTC3198GR FN1016 FP1016 E C B E C B 2SB1237Q 2SA933S 2SA1235F DTA114EKA 2SK2158 2SC2714O DTA144EKA 2SC3052F...
Page 32
IC DESCRIPTION LC876596W-5T96 Pin No. Pin Name Description Common serial clock output. DATA Common serial data output. Common serial strobe output. CS-RHYTHM Rhythm IC chip select output. I-RDSDATA RDS input data (Connected to ground). HP-MUTE Headphone plug-in detect input (output "L" at HOLD). O-POWER System power ON / OFF output.
Page 35
ADJUSTMENT 2 <TUNER / FRONT> < TUNER SECTION > 1. Clock Frequency Check 7. DC Balance / Mono Distortion Adjustment Settings : • Test point : TP6 (CLK) Settings : • Test point : TP4, TP5 (DC balance) Method : Set to AM 1710kHz and check that the test point is TP8 (Lch), TP9 (Rch) 2160kHz ±...
CD TEST MODE 1. How to Activate CD Test Mode While pressing and holding the function button, insert the AC plug. When the test mode starts, the message, “ TEST” appears on the display. 2. How to Cancel CD Test Mode Press the POWER button or remove the AC plug.
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) Type.1 Type.4 Insert a flat-bladed screwdriver into the position indicated by the TOOLS arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer unit and then remove the speaker units. 2 (() flat head screwdriver 3 Cut chisel How to Remove the PANEL, FR...