Diagnostic Chart; Resetting From Lockout; Maintenance; Annual Inspection - Goodman GMV95 Installation Instructions Manual

recharge your body with static electricity; (i.e., do not move
or shuffle your feet, do not touch ungrounded objects, etc.).
If you come in contact with an ungrounded object, repeat
step 2 before touching control or wires.
4. Discharge your body to ground before removing a new
control from its container. Follow steps 1 through 3 if
installing the control on a furnace. Return any old or new
controls to their containers before touching any ungrounded
object.
D C
IAGNOSTIC HART
T
O AVOID ELECTRICAL SHOCK, INJURY OR DEATH, DISCONNECT ELECTRICAL
POWER BEFORE PERFORMING ANY SERVICE OR MAINTENANCE.
Refer to the Troubleshooting Chart at the end of this manual for
assistance in determining the source of unit operational problems.
The red diagnostic LED blinks to assist in troubleshooting the unit.
The number of blinks refers to a specific fault code.
R F L
ESETTING ROM OCKOUT
Furnace lockout results when a furnace is unable to achieve igni-
tion after three attempts. It is characterized by a non-functioning
furnace and a one flash diagnostic LED code. If the furnace is in
"lockout", it will (or can be) reset in any of the following ways.
1. Automatic reset. The integrated control module will
automatically reset itself and attempt to resume normal
operations following a one hour lockout period.
2. Manual power interruption. Interrupt 115 volt power to the
furnace for 1 - 20 seconds.
3. Manual thermostat cycle. Lower the thermostat so that
there is no longer a call for heat then reset to previous setting.
Interrupt thermostat signal to the furnace for 1 - 20 seconds.
NOTE: If the condition which originally caused the lockout still
exists, the control will return to lockout. Refer to Section XVIII,
Troubleshooting - Diagnostic Chart for aid in determining the cause.
XIX. MAINTENANCE
T
O AVOID ELECTRICAL SHOCK, INJURY OR DEATH, DISCONNECT ELECTRICAL
POWER BEFORE PERFORMING ANY MAINTENANCE. IF YOU MUST HANDLE THE
T
IGNITER, HANDLE WITH CARE.
FINGERS, ROUGH HANDLING, OR VIBRATION COULD DAMAGE THE IGNITER
RESULTING IN PREMATURE FAILURE.
EVER HANDLE THE IGNITER.
A
NNUAL INSPECTION
The furnace should be inspected by a qualified installer, or service
agency at least once per year. This check should be performed at
the beginning of the heating season. This will ensure that all fur-
nace components are in proper working order and that the heating
system functions appropriately. Pay particular attention to the fol-
lowing items. Repair or service as necessary.
•
Flue pipe system. Check for blockage and/or leakage. Check
the outside termination and the connections at and internal
to the furnace.
•
Heat exchanger. Check for corrosion and/or buildup within
the heat exchanger passageways.
•
Burners. Check for proper ignition, burner flame, and flame
sense.
*NOTE: Please contact your distributor or our website for the applicable product data book referred to in this manual.
WARNING
WARNING
OUCHING THE IGNITER ELEMENT WITH BARE
O
NLY A QUALIFIED SERVICER SHOULD
•
Drainage system. Check for blockage and/or leakage.
Check hose connections at and internal to furnace.
•
Wiring. Check electrical connections for tightness and/or
corrosion. Check wires for damage.
•

Filters.

F
ILTERS
T
O ENSURE PROPER UNIT PERFORMANCE, ADHERE TO THE FILTER SIZES
RECOMMENDED
GIVEN IN THE
P D B
RODUCT ATA OOK APPLICABLE TO YOUR MODEL*.
M
AINTENANCE
Improper filter maintenance is the most common cause of inadequate
heating or cooling performance. Filters should be cleaned (perma-
nent) or replaced (disposable) every two months or as required.
When replacing a filter, it must be replaced with a filter of the same
type and size.
F R
ILTER EMOVAL
Depending on the installation, differing filter arrangements can be
applied. Filters can be installed in either the central return register
or a side panel external filter rack (upflow only). A media air filter or
electronic air cleaner can be used as an alternate filter. Follow the
filter sizes given in the Recommended Minimum Filter size table to
ensure proper unit performance.
To remove filters from an external filter rack in an upright upflow
installation, follow the directions provided with external filter rack kit.
To remove internal filters see Internal Filter Removal section. Inter-
nal filters are an accessory item and are not included with your
furnace. For further details, see your distributor.
H U F R
ORIZONTAL NIT ILTER
Filters in horizontal installations are located in the central return reg-
ister or the ductwork near the furnace.
To remove:
1. Turn OFF electrical power to furnace.
2. Remove filter(s) from the central return register or ductwork.
3. Replace filter(s) by reversing the procedure for removal.
4. Turn ON electrical power to furnace.
M A F E
EDIA IR ILTER OR LECTRONIC
Follow the manufacturer's directions for service.
B
URNERS
Visually inspect the burner flames periodically during the heating
season. Turn on the furnace at the thermostat and allow several
minutes for flames to stabilize, since any dislodged dust will alter
the flames normal appearance. Flames should be stable, quiet, soft,
and blue (dust may cause orange tips but they must not be yellow).
They should extend directly outward from the burners without curl-
ing, floating, or lifting off. Flames must not impinge on the sides of
the heat exchanger firing tubes.
I D C
NDUCED RAFT AND IRCULATOR
The bearings in the induced draft blower and circulator blower mo-
tors are permanently lubricated by the manufacturer. No further lu-
brication is required. Check motor windings for accumulation of
dust which may cause overheating. Clean as necessary.
34
CAUTION
M F S T
INIMUM ILTER IZE ABLE OR
EMOVAL
A C R
IR LEANER EMOVAL
B
LOWERS